[n00b]]Ethernet GW - without NF24

afick

gr8 but do you have any documentation or help-docs for this or anything what can help me in setting up this?

hek

Currently no documentation for this branch but all the examples has been updated.

You should be able to use any one of the examples and add:

#define MY_GATEWAY_SERIAL

and remove

#define MY_RADIO_NRF24

before the MySensors.h-include.

brix7be

Hello Hek, Hello Everyone,

I've actually one arduino uno and an ethernet shield Wizenet W5100 and for exemple a temp sensor DS18B20 directly connected to it.
I can send to a serial terminal the temperature value. It's working properly :-).
I would to know how I could simplify the code of the "Ethernet GW" Sketch for send the value of a sensor directly from the GW to Domoticz. (Without using an urduino dedicated to the sensor acquisition and without an RF module).

Could you give me an exemple of the code or the command to send to domoticz?
Or do you have a documentation link?
Because the link you posted before is dead https://github.com/mysensors/Arduino/tree/gateway-refactoring.

I've made many rescearch, and i don't find the protocol documentation to discuss with domoticz!

I appreciate if you could help me to the right way :-).

Awayting your answer, thanks very much in advance.

PS: Sorry for my bad english...

hek

The code has been merged into development-branch now:

https://github.com/mysensors/Arduino

brix7be

Thanks for your quickly answer.

I'm sorry but I didn't found the code or information regarde my question into the repository you noticed.

Could you please give me the complete link?

Thanks you again.

hek

We can't have all permutations of examples ready available...

So you'll have to put it together by combining:

https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/examples/GatewayW5100/GatewayW5100.ino

and

https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/examples/DallasTemperatureSensor/DallasTemperatureSensor.ino

You'd basically only have to copy the #defines from the gateway to the DallasTemp-sketch.

brix7be

Hi Hek,

Sure, you can't realise every solutions or exemple for everyone :-).
So it's a good advice for me to begin my tests.

When i merge the both codes, i receive an error "sendSketchInfo was not declared in this scope"!
I've checked and normally all the librairies are available for the code.
(When i'm building the GatewayW5100 only it works) but not for the dallas.

Do you have an idea?

Thanks :-).

Gwen.

hek

Just did a quick test calling sendSketchInfo in the gateway and it compiles fine for me.

brix7be

hum, strange.
I continue to search a solution.
I'll give you a feed back ;-).

Thanks

brix7be

It doesn't work.
But i found the code of Bram81 http://forum.mysensors.org/topic/1591/how-to-add-a-sensor-to-the-serial-gateway/22
and I can compile it well.
And it calls the gw.sendSketchInfo("Soil_Moist_Sensor_grb", "1.15");

Do you have another tip?

hek

remove "gw." from the call.

brix7be

You are right, it blocks when i call sendSketchInfo directly (without to be an attribute of gw) !?!

brix7be

Here is the merged code
Thanks for the advices

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24 
//#define MY_RADIO_RFM69 // I DONT WANT TO USE THE RADIO MODULE

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with 
// radio on the same spi bus.
//#if !defined(MY_W5100_SPI_EN)
//  #define MY_SOFTSPI
//  #define MY_SOFT_SPI_SCK_PIN 14
//  #define MY_SOFT_SPI_MISO_PIN 16
//  #define MY_SOFT_SPI_MOSI_PIN 15
//#endif  

// When W5100 is connected we have to move CE/CSN pins for NRF radio
//#define MY_RF24_CE_PIN 5
//#define MY_RF24_CS_PIN 6

// Enable to UDP          
//#define MY_USE_UDP

//#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
//#define MY_PORT 5003 
     
#define IP_PORT 5003        // The port you want to open 
IPAddress myIp (192, 168, 1, 100);  // Configure your static ip-address here    COMPILE ERROR HERE? Use Arduino IDE 1.5.7 or later!

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
//#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };  // DEAD BEEF FEED

// a R/W server on the port
EthernetServer server = EthernetServer(IP_PORT);
// handle to open connection
EthernetClient client = EthernetClient();

// Flash leds on rx/tx/err
//#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
//#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3 

//#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>

#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>


//-------------------------------------------------------------
//Below the Dallas temp sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
//#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensor.h>  
#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
int inputPos = 0;
bool sentReady = false;

void output(const char *fmt, ... ) {
   va_list args;
   va_start (args, fmt );
   vsnprintf_P(serialBuffer, MAX_SEND_LENGTH, fmt, args);
   va_end (args);
   Serial.print(serialBuffer);
   server.write(serialBuffer);
}

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(mac, myIp);

  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

hek

Looks like you added your own stuff..

@brix7be said:

IPAddress myIp (192, 168, 1, 100); // Configure your static ip-address here COMPILE ERROR HERE? Use Arduino IDE 1.5.7 or later!

Should simply be
#define MY_IP_ADDRESS 192, 168, 1, 100 // If this is disabled, DHCP is used to retrieve address

And what the following doing here?

// a R/W server on the port
EthernetServer server = EthernetServer(IP_PORT);
// handle to open connection
EthernetClient client = EthernetClient();

And you include <SPI.h> and <MySensor.h> twice.

brix7be

to be honnest, i don't know ...

brix7be

With the #define MY_IP_ADDRESS i can't compile the projet.
With the arduino command it works now, i can ping it on 192.168.1.100.
But still nothing in domoticz.
Am I on the right way?
thanks again :-)

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable to UDP          
//#define MY_USE_UDP

//#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
byte ip[] = { 192, 168, 1, 100 }; 
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
//#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
byte mac [] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};

#include <SPI.h>
#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>

//-------------------------------------------------------------
//Below the Dallas temp sketch

#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(mac , ip);
  wait(1000);
  
    // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

hek

I don't understand.. why do you declare ip and mac like that? It most surely isn't picked up by the library. You're probably just getting an ip from your DHCP server.

What compile error do you get when using the defines?

brix7be

i've changed as before and it won't compile.
The error is:
no matching function for call to 'EthernetClass::begin(int, int, int, int, int, int, int, int, int, int)'
No it takes the ip I put on the code before, cause the ping respond at this one.
Thks

// BELOW the gateway W5100 sketch

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable to UDP          
//#define MY_USE_UDP

#define MY_IP_ADDRESS 192,168,1,100   // If this is disabled, DHCP is used to retrieve address
//byte ip[] = { 192, 168, 1, 100 }; 
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
//byte mac [] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};

#include <SPI.h>
#if defined(MY_USE_UDP)
  #include <EthernetUdp.h>
#endif
#include <Ethernet.h>
#include <MySensor.h>

//-------------------------------------------------------------
//Below the Dallas temp sketch

#include <DallasTemperature.h>
#include <OneWire.h>

#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
boolean receivedConfig = false;
boolean metric = true; 
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup()  
{ 
  // ////Prepare the ethernet connection 
  Ethernet.begin(MY_MAC_ADDRESS , MY_IP_ADDRESS);
  wait(1000);
  
    // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {
 
    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;
 
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  sleep(SLEEP_TIME);
}

brix7be

The final goal for me is the build ethernet sensor(s) (2 or 3 one each arduino board) connected to domoticz by lan gw.

brix7be

Is there anyone who have done a sketch to connect sensor directly on an ethernet gateway ?
Iam searching a working exemple or a working draft to see the process to build my own code.
Thank everyone for your advices.

[n00b]]Ethernet GW - without NF24

16

11.7k

11.2k

113.0k