Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Node.js Modules for MySensors

wpreul last edited by

Here are a couple of node.js modules I wrote a while back for mysensors you all may find useful:

https://www.npmjs.com/package/sensors <- Parse and Stringify the protocol

https://www.npmjs.com/package/cowboymouth <- streams support for the protocol
Reply Quote 1
1 Reply Last reply
tbowmo Admin last edited by

@wpreul

There are also modules available for node-red: http://forum.mysensors.org/topic/1965/nodered-injected-between-domoticz-and-mysensors

https://www.npmjs.com/package/node-red-contrib-mysensors
Reply Quote 0
1 Reply Last reply

2
Posts

1233
Views

Log in to reply

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3307
Views

No one has replied
Gateway without a radio
Development • • OldSurferDude

3

0
Votes

3
Posts

25
Views

@OldSurferDude yes, just run the configure command with --my-transport=none
[mysensors] Not a valid message: invalid literal for int() with base 10: '\x00\x000'
Development • • kiesel

3

0
Votes

3
Posts

18
Views

Thanks, I'll keep this in mind if I decide to debug it. I realized that I am also tired of patching the gateway through to the doctor container inside an LXC so now I am looking at creating an esp gateway. Just need to check if I can find a pcb on here. Thanks again!
MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

6

0
Votes

6
Posts

28
Views

@bgunnarb I like @eiten 's solution for you. Personally, I am not a fan of using cloud/public brokers. Thus I am curious about your system and there is something about it from which I can learn. I would like to understand why you cannot deploy your own mosquitto broker. I see your set up as 3 sensor groups defined by the channel used #define MY_RF24_CHANNEL ChannelOfSensorGroup Each sensor group has some number of sensors and one MQTT GW on ESP8266. On the MQTT side, do you distinguish between gateways by using a different host name? Something like: #define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway-nOf3-out" #define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway-nOf3-in" #define MY_MQTT_CLIENT_ID "mysensors-nOf3" #define MY_HOSTNAME "ESP8266_MQTT_GW_nOf3" //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_URL_ADDRESS "test.mosquitto.org" #define MY_PORT 1883 I must assume your controller (aka Home Assistant) discriminates between through which gateway the data is to flow by way of the different topic names. If my "something like" is correct, then changing brokers is changing the IPaddress/URL in your gateways and in your controller (though if the controller is Home Assistant, it may be a bother because the device-id's may change which will make a mess of all the work you've done in HA. This is why I like @eiten 's solution.) I hope it's all working for you again. OSD
Radio waking up for no reason.
Development • • Sasquatch

3

0
Votes

3
Posts

35
Views

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!

72
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1