💬 Sensebender Gateway

[tbowmo]

@stefaanv

No, it doesn't need a driver..

I get the same for mine, if I use setserial:

thomas at jarvis in ~ 
>sudo setserial /dev/ttyNRF24 
/dev/ttyNRF24, UART: unknown, Port: 0x0000, IRQ: 0, Flags: low_latency
thomas at jarvis in ~ 
>ll /dev/ttyNRF24 
lrwxrwxrwx 1 root root 7 nov 11 13:39 /dev/ttyNRF24 -> ttyACM1

Btw. the permission problem.. You are logged in using your normal user (stefaan) and then you set permissions for openhab user? (see below). Have you tried setting the permissions for your user, and then cat /dev/ttyACM0?

@stefaanv said in 💬 Sensebender Gateway:

There seems to be a premissions problem om the port :
stefaan@home:~$ cat /dev/ttyACM0
cat: /dev/ttyACM0: Permission denied

doing 'sudo usermod -a -G dialout openhab' doesn't help

Anyone any ideas ?

[stefaanv]

@tbowmo OK, is working now after restarting the bundle in OH.
Must have been the permission problem after all.
Thanks for your help !!

[rzylius]

When I try to compile SensebenderGW sketch with signing features, I receive a bunch of errors. What am I missing?

Arduino: 1.8.5 (Windows Store 1.8.10.0) (Windows 10), Board: "Sensebender Gateway"

In file included from C:\Users\rzylius\AppData\Local\Temp\arduino_modified_sketch_737033\SensebenderGatewaySerial.ino:88:0:

C:\Users\rzylius\Documents\Arduino\libraries\MySensors/drivers/ATSHA204/ATSHA204.cpp:6:16: error: redefinition of 'uint8_t device_pin'

static uint8_t device_pin;

            ^

In file included from C:\Users\rzylius\Documents\Arduino\libraries\MySensors/MySensors.h:131:0,

             from C:\Users\rzylius\AppData\Local\Temp\arduino_modified_sketch_737033\SensebenderGatewaySerial.ino:86:

C:\Users\rzylius\Documents\Arduino\libraries\MySensors/drivers/ATSHA204/ATSHA204.cpp:6:16: error: 'uint8_t device_pin' previously declared here

static uint8_t device_pin;

            ^

In file included from C:\Users\rzylius\AppData\Local\Temp\arduino_modified_sketch_737033\SensebenderGatewaySerial.ino:88:0:

C:\Users\rzylius\Documents\Arduino\libraries\MySensors/drivers/ATSHA204/ATSHA204.cpp: In function 'void swi_set_signal_pin(uint8_t)':

C:\Users\rzylius\Documents\Arduino\libraries\MySensors/drivers/ATSHA204/ATSHA204.cpp:24:13: error: redefinition of 'void swi_set_signal_pin(uint8_t)'

static void swi_set_signal_pin(uint8_t is_high)

         ^

In file included from C:\Users\rzylius\Documents\Arduino\libraries\MySensors/MySensors.h:131:0,

             from C:\Users\rzylius\AppData\Local\Temp\arduino_modified_sketch_737033\SensebenderGatewaySerial.ino:86:

C:\Users\rzylius\Documents\Arduino\libraries\MySensors/drivers/ATSHA204/ATSHA204.cpp:24:13: error: 'void swi_set_signal_pin(uint8_t)' previously defined here

static void swi_set_signal_pin(uint8_t is_high)

         ^

and the same type of errors reoccurs multiple times.

[Anticimex]

@rzylius I think you have an #include in the sketch for the atsha driver. Try to remove that #include from the sketch.

[rzylius]

@Anticimex yes, when I delete #include atsha driver line, it compiles well. thanks.

[Fabien]

@tbowmo After 2 month on the dev version, no more problem with the gateway. Perhaps it's time to made a new stable release ?

[tbowmo]

@Fabien

It's on the todo list.. :)

[8667]

I am looking for Gateway that will get me the results to MQTT but will support encryption + signing. That mean it should be easy to add new signatures (recompile/reflash) the module

I suppose if I use Sensebender with LAN module it will be a pain to do that

Is this doable if I use Orange zero as USB host for the Sensbender and let it act as serial gateway, then convert serial to mqtt with software on the Linux side? Also is it possible to reflash it easily this way? I do not want to rewire the hardware each time a add new node.

[tbowmo]

@8667

Is it over the air encryption / signing that you are aiming after? Then that is possible with the gateway, it has the ATSHA204 onboard for signing capabilities. And it also works with the W5100 module attached. The Gateway have 256Kb of flash onboard, so it has "enough" room for both network stack, and signing.

[rzylius]

Are there performance limitations to be considered for mysensors and SensebenderGW specifically. Will the gateway handle the load of signed communications if rules will be firing messages to different sensors like 1-2-5-10 per second?

[Anticimex]

@rzylius if you use the atsha204a chip, it is the single wire interface that limits your throughput. I have no figures, so best is to just test how fast you can push messages through. Of course there is overhead in the OTA handshaking as well. That would probably be the bottleneck if you use software based signing.

[rzylius]

I see in logs, that the whole process of signing and communicating to the node takes a bit more than one second. I do not know how to make a stress test properly, so I hoped that somebody else did it :) my question is if gateway will handle load by putting messages in some pipeline, or I should try to make sure that messages are fired with some spaces.

[Anticimex]

@rzylius The signing process is blocking, so it should not accept messages if a signed message exchange is in progress. But I have not tested that extensively with "aggressive" controllers.

[Mitja Blazinsek]

im trying to program in arduino ide, installed board... bu when compiling it write mi an error 'The current selected board needs the core 'arduino:arduino' that is not installed.'

[mfalkvidd]

@mitja-blazinsek You'll need to install the Arduino SAMD board as well. I have just now updated the readme.

[dklinkman]

Just got my Sensebender GW and soldered it up. Adapted the serial sketch to Ethernet and it almost worked. Found some posts on this topic that helped me locate and fix my config error. Now all is well. Thanks! --edit-- added photo

-d

[dklinkman]

@dklinkman said in 💬 Sensebender Gateway:

Sensebender

And I got a Sensebender Micro soldered up and running also!! Just temp and humid so far. Too cool

--edit-- picture

[Soloam]

This post is deleted!

[8667]

Is it possible to use the sensebender board as MQTT gateway? Not Ethernet?

[Soloam]

Yes it is! I use I'm using it as a MQTT gateway for some time