Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Mysensors Library Update location

rmtucker last edited by

I have been using the Development branch for a while now.
I downloaded the zip and unzipped it into my sketch folder as per instructions.
Now i want to update to the latest version.
Do i just unzip to the same directory and overwrite or do i delete the old library somehow.
Very confusing because i assume i would have to back up any work i have in there first??
Reply Quote 0
1 Reply Last reply

1
Posts

713
Views

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

1

0
Votes

1
Posts

3310
Views

No one has replied
Saving last known good state, but not in EEPROM
Development • • OldSurferDude

6

0
Votes

6
Posts

33
Views

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

3

0
Votes

3
Posts

21
Views

@mfalkvidd Yes, I understand that 253 is the software limit. I was wondering about the hardware limit. For example, my Asus router has a software limit of 253 devices. But when I get 20-25 WiFi devices trying to connect, the network goes haywire. (pun intended ) I am quite convinced that this is a hardware limitation of the router because the router has to carry some information about each connection. If the gateway is dumb, that is, carries no information about any connection, then it could truly have 253 connections. After a bit of contemplation, I realize that the name, gateway, implies this. If that is the case, it is good news for the DiY'er in that this very inexpensive and cheap hardware could stand in for a LoRaWAN, again, with a number of compromises.
Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

3

1
Votes

3
Posts

25
Views

@mfalkvidd Thank you very much, that's exactly what I was looking for!
PJON and Minicore not working
Development • • Trand

1

0
Votes

1
Posts

14
Views

No one has replied
MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

11

0
Votes

11
Posts

53
Views

@dpcons MQTT sounds intimidating and looks imitimidating when you see all of the options available. Here's the scenario: You want to send a message. That's the -m option followed by a space and the message between " " the location, topic, is a tree, -t option, separated by forward slash / eg. MyRootTopic/MyTopicsSub/MyTopicSubSub It's as easy as that if your broker, the MQTT service (program) is on the same computer as the sending program. Usually it's not. Specifiy the location, the host, of the broker with the -h option followed by the host name or IP address The retain option, -r is important but explaining it is beyone the scope of this message Receiving, subscribing, to a topic is just the same, but you wouldn't have the -m message If you subscribe from the command line, the subscribe function waits indefinitely for messages published to the subscribed topic (unless you use the -C option) ^C to terminate the command. A tamotized device with the MQTT configured will create a number of topics on the broker. Home Assistant will see this automatically, if you have the Tasmota and MQTT Integrations installed. The MySensors MQTT gateway takes care of MQTT communication for a MySensors device. Again the MySensors and MQTT integrations. I use both. -OSD

Mysensors Library Update location

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

PJON and Minicore not working
Development • • Trand

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

23
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Mysensors Library Update location

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

Saving last known good state, but not in EEPROM Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

PJON and Minicore not working Development • • Trand

MQTT-Help me understand about the MQTT Gateway. Development • • dpcons

23Online

11.7kUsers

11.2kTopics

113.0kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

Saving last known good state, but not in EEPROM
Development • • OldSurferDude

Imitating a LoRaWAN(R) with ESP8266/ESP32 and MySensors
Development • • OldSurferDude

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

PJON and Minicore not working
Development • • Trand

MQTT-Help me understand about the MQTT Gateway.
Development • • dpcons

23
Online

11.7k
Users

11.2k
Topics

113.0k
Posts