💬 NRF2RFM69
-
use a 4.7uF capacitor, or there about..
There is no pads for a SMA connector, but you could attach one with a pigtail..
-
just one more question... I have on the Gateway a RFM69HW and a node with a RFM69W module. In the Gateway Sketch is the HW type enabled
#define MY_RFM69_FREQUENCY RF69_868MHZ #define MY_IS_RFM69HWBut there is no comunication from the node... I use Mysensors 2.1.1.
Any idea? -
@gohan It at the Moment only a test. So I have one EasyPCB NRF board with FTDI as Gateway and another EasyPCB board with DHT22 Sensor attached as Node. On both is a 4,7uF electrolytic condensator attached Close to the NRF socket. Both boards are at the Moment with RFM69W 868. The sensor node is battey powered.
-
Get latest 2.2 library and use new rfm69 driver. Did you remember to close the IRQ contact in the easypcb?
@gohan Oh Sh* must check this... I've tried it yesterday on both devices the 2.2 Dev. But will Keep ypu informed...
Don't find the jumperfor the IRQ on the Rev 9 board. can you please post a Picture. Seems that this one is definitly not closed...
--> Edit... found it in the documentation but still the same.
Think the next Point to check for me are the antennas... :-( -
in principle there is traffic between node and Gateway..
159631 !TSM:FPAR:NO REPLY 159637 TSM:FPAR 169848 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 171868 !TSM:FPAR:NO REPLY 171874 TSM:FPAR 179087 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 181106 !TSM:FPAR:FAIL 181112 TSM:FAIL:CNT=4 181118 TSM:FAIL:DIS 181123 TSF:TDI:TSL 191131 TSM:FAIL:RE-INIT 191137 TSM:INIT 191143 TSM:INIT:TSP OK 191150 TSM:INIT:STATID=10 191158 TSF:SID:OK,ID=10 191164 TSM:FPAR 198377 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 200396 !TSM:FPAR:NO REPLY 200402 TSM:FPAR 207616 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 209635 !TSM:FPAR:NO REPLY 209641 TSM:FPAR 216854 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 218873 !TSM:FPAR:NO REPLY 218880 TSM:FPAR 226093 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 228112 !TSM:FPAR:FAIL 228118 TSM:FAIL:CNT=5 228124 TSM:FAIL:DIS 228128 TSF:TDI:TSL 238135 TSM:FAIL:RE-INIT 238141 TSM:INIT 238147 TSM:INIT:TSP OK 238153 TSM:INIT:STATID=10 238161 TSF:SID:OK,ID=10 238168 TSM:FPAR 248385 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 250404 !TSM:FPAR:NO REPLY 250411 TSM:FPAR 257624 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 259643 !TSM:FPAR:NO REPLY 259649 TSM:FPAR 269731 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 271751 !TSM:FPAR:NO REPLY 271757 TSM:FPAR0;255;3;0;9;189196 TSF:PNG:SEND,TO=0 0;255;3;0;9;189206 TSF:CKU:OK 0;255;3;0;9;189214 TSF:MSG:GWL OK 0;255;3;0;9;191236 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 0;255;3;0;9;244555 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 0;255;3;0;9;244574 TSF:MSG:BC 0;255;3;0;9;244582 TSF:MSG:FPAR REQ,ID=10 0;255;3;0;9;244594 TSF:PNG:SEND,TO=0 0;255;3;0;9;244604 TSF:CKU:OK 0;255;3;0;9;244613 TSF:MSG:GWL OK 0;255;3;0;9;257744 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 0;255;3;0;9;269957 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 0;255;3;0;9;269977 TSF:MSG:BC 0;255;3;0;9;269985 TSF:MSG:FPAR REQ,ID=10 0;255;3;0;9;269996 TSF:PNG:SEND,TO=0 0;255;3;0;9;270006 TSF:CKU:OK 0;255;3;0;9;270014 TSF:MSG:GWL OK 0;255;3;0;9;281585 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 0;255;3;0;9;289732 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 0;255;3;0;9;289753 TSF:MSG:BC 0;255;3;0;9;289761 TSF:MSG:FPAR REQ,ID=10 0;255;3;0;9;289771 TSF:PNG:SEND,TO=0 0;255;3;0;9;289781 TSF:CKU:OK 0;255;3;0;9;289789 TSF:MSG:GWL OK 0;255;3;0;9;297015 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 0;255;3;0;9;306757 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 0;255;3;0;9;306776 TSF:MSG:BC 0;255;3;0;9;306784 TSF:MSG:FPAR REQ,ID=10 0;255;3;0;9;306796 TSF:PNG:SEND,TO=0 0;255;3;0;9;306806 TSF:CKU:OK 0;255;3;0;9;306814 TSF:MSG:GWL OK 0;255;3;0;9;316682 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 0;255;3;0;9;322084 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 0;255;3;0;9;322103 TSF:MSG:BC 0;255;3;0;9;322111 TSF:MSG:FPAR REQ,ID=10 0;255;3;0;9;322123 TSF:PNG:SEND,TO=0 0;255;3;0;9;322131 TSF:CKU:OK 0;255;3;0;9;322142 TSF:MSG:GWL OK 0;255;3;0;9;333180 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 -
@Markus. You have an RF issue. Typically for nrf24l01+ I'd use a different power supply or a different module.
Are you sure both modules are set to the same channel and frequency? What antennas are you using?
Do you have HW modules? -
@alexsh1 I use at the Moment RFm69W 868 modules not NRF. Because the RFMs are mounted on the NRF connector on an EasyPCB. I use at the Moment single wire antennas with a lenght of 8,3 cm.
-
@alexsh1 should be, becaus ist not defined explicit in the Sketch. By Default in the MYS Lib 2.2 dev is it 868 mhz. And when i try to define the frequency in the Sketch. Like
#define MY_RFM69_FREQUENCY RF69_868MHZ
I get the error message.'RF69_868MHZ' was not declared in this scope -
@alexsh1 should be, becaus ist not defined explicit in the Sketch. By Default in the MYS Lib 2.2 dev is it 868 mhz. And when i try to define the frequency in the Sketch. Like
#define MY_RFM69_FREQUENCY RF69_868MHZ
I get the error message.'RF69_868MHZ' was not declared in this scope -
@mfalkvidd you are right... Ist now added in the GW and node Sketch, but still the same Problem.
-
I think at the end will it be a power problem. It seems that the sensor node powered with 2x AA cells can not handle the Radio on TX/RX. The same on the Gateway site which is also a Easy PBB powered fom the FTDI Connector connected to USB. The question now is how can i fix this power Problems ? Or more, how can i make sure that this is definitly not the reason.
