battery level doesn't appear ?

[flopp]

This is from my GW

0;0;3;0;18;PING0;0;3;0;9;read: 12-12-0 s=255,c=3,t=0,pt=1,l=1,sg=0:98
12;255;3;0;0;98
0;0;3;0;9;read: 12-12-0 s=1,c=1,t=38,pt=7,l=5,sg=0:2.979
12;1;1;0;38;2.979
0;0;3;0;9;read: 12-12-0 s=0,c=1,t=23,pt=3,l=2,sg=0:66
12;0;1;0;23;66
Finished

98% battery
2.979 voltage
66 lux

[flopp]

You can also restart your Node and then it will send all data again like, Sketchname, version and also all childs

[flylowgofast]

my loop(){}

// the loop routine runs over and over again forever:
void loop() {

  // Process incoming messages (like config from server)
  gw.process();  

  //---------------Lecture des ouvertures de porte------------------
  doorOpenOffState = digitalRead(HALLOFFICEDOOR); // lecture à chaque cycle (urgence)
  if (doorOpenOffState != doorOpenOffChange){
    gw.send(msgDoorOffice.setSensor(OFFICEDOOR).set(doorOpenOffState));
    doorOpenOffChange = doorOpenOffState;
  }

  doorOpenBedState = digitalRead(HALLBEDROOMDOOR); // lecture à chaque cycle (urgence)
  if (doorOpenBedState != doorOpenBedChange){
    gw.send(msgDoorBedroom.setSensor(BEDROOMDOOR).set(doorOpenBedState));
    doorOpenBedChange = doorOpenBedState;
  }
  
  if (digitalRead(ECLEXT) != oldInterExt){
    oldInterExt = !oldInterExt;
    eclState = !eclState;
    gw.send(msgLightSwitch.set(eclState));
  }

  //---------------Envoi du niveau de batterie !! pour rester eveillé------------------
  /*if ((millis() - myTime) > 10000) { // toutes les dix secondes
    myTime = millis();
    gw.sendBatteryLevel(97,1);
  } else {
    if ((millis() - myTime) < 0) {
      myTime = millis();
    }
  }*/
  gw.sendBatteryLevel(97,1);

// ---------------Traitement volet 1-----------------
  analogUpV1 = analogRead(UPV1);
  if ((analogUpV1 <25) && !manOnV1) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air)
    digitalWrite(TRIAC5, HIGH);
    digitalWrite(TRIAC2, LOW);
    triacTempoV1 = millis();
    triacManPriorityV1 = true;
    manOnV1 = true;
    memoStopV1 = false;
  } else {
    analogDownV1 = analogRead(DOWNV1);
    if ((analogDownV1 <25) && !manOnV1) { //proche de zéro
      digitalWrite(TRIAC5, LOW);
      digitalWrite(TRIAC2, HIGH);
      triacTempoV1 = millis();
      triacManPriorityV1 = true;
      manOnV1 = true;
      memoStopV1 = false;
    } else {
      if (analogUpV1 > 800 && analogDownV1 > 800 && !memoStopV1){ // les deux fils en l'air
        digitalWrite(TRIAC5, LOW);
        digitalWrite(TRIAC2, LOW);
        triacManPriorityV1 = false;
        manOnV1 = false;
        memoStopV1 = true;
      } else {
        if (!triacManPriorityV1){
          if (shutterOff1State && shutterOff2State) {
            shutterOff1State = false;
            shutterOff2State = false;
            digitalWrite(TRIAC5, LOW);
            digitalWrite(TRIAC2, LOW);
          } else {
            if (shutterOff1State) {
              shutterOff1State = false;
              digitalWrite(TRIAC5, HIGH);
              digitalWrite(TRIAC2, LOW);
              triacTempoV1 = millis();
            } else {
              if (shutterOff2State) {
                shutterOff2State = false;
                digitalWrite(TRIAC5, LOW);
                digitalWrite(TRIAC2, HIGH);
                triacTempoV1 = millis();
              }
            }
          }
        }
      }
    }
  }
  if (((triacTempoV1 + TEMPOOPENV1) < millis())) {
    digitalWrite(TRIAC5, LOW);
    digitalWrite(TRIAC2, LOW);
    triacManPriorityV1 = false;
  }

// --------------------------Traitement volet 2------------------------
  analogUpV2 = analogRead(UPV2);
  if ((analogUpV2 <25) && !manOnV2) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air)
    digitalWrite(TRIAC3, HIGH);
    digitalWrite(TRIAC4, LOW);
    triacTempoV2 = millis();
    triacManPriorityV2 = true;
    manOnV2 = true;
    memoStopV2 = false;
  } else {
    analogDownV2 = analogRead(DOWNV2);
    if ((analogDownV2 <25) && !manOnV2) { //proche de zéro
      digitalWrite(TRIAC3, LOW);
      digitalWrite(TRIAC4, HIGH);      
      triacTempoV2 = millis();
      triacManPriorityV2 = true;
      manOnV2 = true;
      memoStopV2 = false;
    } else {
      if (analogUpV2 > 800 && analogDownV2 > 800 && !memoStopV2){ // les deux fils en l'air
        digitalWrite(TRIAC3, LOW);
        digitalWrite(TRIAC4, LOW);        
        //triac3 = false;
        //triac4 = false;
        triacManPriorityV2 = false;
        manOnV2 = false;
        memoStopV2 = true;
      } else {
        if (!triacManPriorityV2){
          if (shutterBed1State && shutterBed2State) {
            shutterBed1State = false;
            shutterBed2State = false;
            digitalWrite(TRIAC3, LOW);
            digitalWrite(TRIAC4, LOW);            
          } else {
            if (shutterBed1State) {
              shutterBed1State = false;
              digitalWrite(TRIAC3, HIGH);
              digitalWrite(TRIAC4, LOW);              
              triacTempoV2 = millis();
            } else {
              if (shutterBed2State) {
                shutterBed2State = false;
                digitalWrite(TRIAC3, LOW);
                digitalWrite(TRIAC4, HIGH);                
                triacTempoV2 = millis();
              }
            }
          }
        }
      }
    }
  }
  if (((triacTempoV2 + TEMPOOPENV2) < millis())) {
    digitalWrite(TRIAC3, LOW);
    digitalWrite(TRIAC4, LOW);      
    triacManPriorityV2 = false;
  }
}

[flopp]

@flylowgofast
Look ok

[AWI]

@flylowgofast for information on the logs take a look at the debug topic

[flylowgofast]

My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !

[AWI]

@flylowgofast From what I read from your sketch you seem to do some high voltage / current switching. Especially the radio doesn't like all kinds of electronic disturbances (emc etc.) To avoid lockups you need to pay special attention/separate power supplies (if you haven't done already).

[flylowgofast]

Hello AWI,

Thanks for your reply, yes my node trigs 5 triacs. I use snubber, regulator, capacitor. And ond the other hand, all commands to the node work properly ? just battery level doesn't work and after several hours NRF24L01 stop to work.
I would like to reset NRF24L01 but with MySensors we don't have direct access to it anymore. Perhaps there is a way to reset the sketch globaly ?

thanks for your help

[flopp]

@flylowgofast said:

My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !

It would have been nice if you had wrote this in your first post.:disappointed:
So everyone could focus on the main problem

[flylowgofast]

Hello @flopp ,

Sorry I was myself focus on this second problem that's interesting to solve too ?
At the end twice aren't solve ! :disappointed:

[flylowgofast]

Hello all,

At the end, I choose to do a software reset every 24 hours. This solution is very bad for me but it works !!

bye

[sundberg84]

@flylowgofast One simple thing can be to move the radio away a bit and see if that helps. Its as AWI said probably interferance power-radio.

[flylowgofast]

Hello @sundberg84,
I already considered this idea but my node have been running perfectly for two days before failed. So I think, power consideration are not the problem. I can trigg on and off my shutters many and many times without problem.