💬 MyMultisensors
-
@carlierd hello. hehe yep a bit complete, very memory ric-rac limited :) It's rssi of the node tuned by ATC ;) I have modified libs, but i'm late on pr...sorry
-
Yo,
for those who have not seen my latest rev..apologize, I'm working hard to release all my stuff ;)
It's still working well btw. this is the revision i will release i think (i have few other nice iteration but that's enough!).
- Size is 25mmx49mm (same size as a nodemcu)
- Same specs as before, plus OTA. So optimized for very low power and coincell management. Temp/hum/pir/lux/contact door input
- Thickness depends on the battery used. That's great as now it's possible to use different kind of battery holder :) CR2032 for the thinnest (8mm without PIR) very thin!, CR2450, or through hole 2xAAA holder
- you can see a test I want to try: a special antenna i saw on the forum. I will compare it with straight wire antenna, and coiled wire antenna.
See you soon :)
-
another little pic :yum:
left to right: 1) pcb without holder, 2) with cr2032 holder, 3) cr2450, 4) 2xaaa
different antenna format, i have not compared yet. But the straight one, if i remember well, reached 40-50m range with one brick wall (All are the low power version of rfm69, CW). As you can see the coiled antenna (4) does not take so much place compared to the 1.9€ special ant (3).
I can cover a nice range of use, yeah :) -
Hi @carlierd
i'll fix this! There is still my first version i posted there, on the old topic, https://forum.mysensors.org/topic/3600/my-other-pir-multisensor-on-coin-cell
PIR is repsonding well, depending of the sensitivity i set in sketch. same for batt!
Many sensors but all low power :) Except reed switch option, of course my power consumption results above are without reed switch. If i need it, i use a 1M res min (increase a few uA).see you soon
-
@anticimex almost! in fact i noticed that's mostly the same schematic if you look at different source. of course it's a PIR ! Regarding the app note you showed me, resistors, capa values changed, and not same ref of comparator (lower power consumption here). so it's very low power :)
-
Would it be possible to buy it pre-assembled soon?
-
Hi.
yes i'm preparing files for the fabhouse.
As you can see i've done a little update on my description, i'm focusing on my "work in progress" stuff to "released" at openhardware because i would like to release my others boards etc. and have my mind free for software. That will be hard for a pcb addict like me :)
I hope we'll get a reasonable price..This will be a project for contributing to Mysensors project ;) -
Hi.
yes i'm preparing files for the fabhouse.
As you can see i've done a little update on my description, i'm focusing on my "work in progress" stuff to "released" at openhardware because i would like to release my others boards etc. and have my mind free for software. That will be hard for a pcb addict like me :)
I hope we'll get a reasonable price..This will be a project for contributing to Mysensors project ;) -
Hi,
is it possible to get the actual sketch ? -
hi.
i've updated the bom. you can use CSTCE8M00G55-R0.
it's optional, you can omit it if you want, and use internal 8mhz -
Hi, which tool do you use for programming with your pogo pin avr isp ?
Why didn't use pogo pin for FTDI too ?
-
@scalz Thx but how do you connect your USBASP on the pogo pins ?
I use an usbasp like this http://d1gsvnjtkwr6dd.cloudfront.net/large/AC-PG-USBASP_LRG.jpg but i don't see how to connect him on the pogo pins ;)
