Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MQTT Gateway change controller IP address

Miloslav Kazda last edited by

Hi all,
is it possible to change MY_CONTROLLER_IP_ADDRESS? I would like to combine WiFiManager with ESP8266 MQTT Gateway. I don't like hardcoded configuration.
Reply Quote 0
1 Reply Last reply

1
Posts

510
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2572
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

17

0
Votes

17
Posts

168
Views

LiFePO4 batteries are a great choice because they have a long life cycle and are much safer than other lithium-based batteries. However, you need a solar charge controller that’s compatible with LiFePO4 to prevent overcharging and maintain efficiency. A good MPPT controller can significantly boost energy harvest from your panels. Also, ensure your solar panel output matches your power needs. If you're in solar ireland, you might find some local companies that offer tailored solutions for maximizing solar efficiency in lower light conditions.
What is form factor?
General Discussion • • Luosi

1

0
Votes

1
Posts

16
Views

No one has replied
Combination of networks
General Discussion • • Sniker

4

0
Votes

4
Posts

16
Views

Take a look on this article https://www.mysensors.org/build/rs485
Running out of nodeId's
General Discussion • mysensors • • NielBierman

10

3
Votes

10
Posts

63
Views

@GLAB You can set the frequencies using the settings in MyConfig.h, which is in the MySensors folder. If you put any of the defines from MyConfig.h into your sketch, they will override the MyConfig.h setting for that sketch only. If you are using the RF24 radio, there are different channels which correspond to a given frequency. The default is channel 76. There is a list of typical channels in MyConfig.h. If you want to change the channel for all the sketches, change it in MyConfig.h. If you want to change it just for the sketch, add a define to the sketch. For example: #define MY_RF24_CHANNEL (84) The problem with changing the channel in a sketch is that the gateway has to be on the same channel to receive from the node. So, normally it makes sense to change in MyConfig.h because you usually want the gateway and all the nodes on the same channel. Other radio's like the RFM69 list the frequency instead of using a channel. They can be overridden in the sketch as well. You can find the defines that are needed in MyConfig.h
GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

15

0
Votes

15
Posts

123
Views

@eiten Ran into the same error but of course the community is always at hand, ready to help! Great! I'm using MySensors 2.3.2 release version. Downgrading the ESP8266 board library to 2.7.4 as suggested by @OldSurferDude did the trick. I'm still clinging to MySensors. So simple and inexpensive to use! All sensors and other stuff connects over three MQTT GW in three locations back to my Home Assistant. PS: Get well soon! Regards, Gunnar