💬 MySensor Dioder (Ikea)

[barduino]

Thanks @mortommy

[mortommy]

please find items and rules here: https://github.com/mortommy/MySensorDioder

[loralg]

@mortommy Thank you!

[mortommy]

I just updated the rules.

[loralg]

@mortommy Awesome thanks for the update!

[kevvette]

Just for clarification, you posted in a comment that S3(AIN2) -> D11 but shouldn't it be D4 per schematic and source code? Also, it looks like R20 has been removed. Why was that done and is it critical to make this work? Thanks, nice work.

[mortommy]

Hi @kevvette ,
yes, my mistake, S3 goes to D4, I'll correct the post, thank you.
Regarding the R20, it is just a jumper and first I thought I could use that point for some connection but at the end I didn't use it, so I reestablished the connection. It is not needed to remove the R20.

[TON RIJNAARD]

Hello,

Very nice project!
Is it possible to use in DOMOTICZ?

Ton

[mortommy]

Hi,

if you are already using a gateway in Domoticz I guess so. From the mysensor point of view is a RGB sensor (or light switch or dimmer light) the source of the command sento to the serial gateway and then to the ikea mysensorized sensor it doesn't matter.

[Juan8taco]

Hello,
I was using your code from MySensorDioder_133.ino
I downloaded the library from https://github.com/mysensors/MySensors
I tried to run the code but I got a error message saying no such file located.
These were the two files that couldn't be found
MyTransportNRF24.h
MySensor.h
I was wondering if you had the same issues when you were working on the code?

[mortommy]

Hi,
yes it happens sometimes. Try to import the library by Arduino IDE (Sketch -> Include Library -> MySensors). You'll have in the sketch two new lines:

#include <MyConfig.h>
#include <MySensors.h>

and you can delete the same lines already included in the code.

Remember that the sketch is based on mysensor library 1.5.4 it is not converted to 2.0 yet.

Hope it helps.

[Juan8taco]

Thank you,

I found those missing files and uses the mysensor library 1.5.4 but after I put all the files it asked for I got this odd message. I was looking for the error but had no luck. It says that "was not declared in this scope". Did you happened to run into this issue?

[mortommy]

Have you cleaned the folder MySensor within the folder libraries before to copy the 1.5.4 one?

[pentti12]

Hello
I got lot of errors during the compiling stage. I tried to use older MySensors 1.5.4 library and Arduino 1.5.7 IDE. My question is, how to install correct MySensors library and not use anything else?

[mortommy]

Delete the MySensors folder in libraries and download it again.

[pentti12]

Now I downloaded Arduino IDE 1.6.5.zip, then I extracted it into C:/tools folder. Then I deleted everything from the library folder. Then I started Arduino IDE and I added MySensors-1.5.4.zip library. IDE reported that this file does not contain valid library. I closed IDE. So I unzipped MySensors-1.5.4.zip library directly into library folder. Then I started again IDE and checked that IDE can see MySensors-1.5.4 library. I opened MySensorDioder_133.ino and tried to compile it.

Still got the following error:

MySensorDioder_133.ino:38:30: fatal error: MyTransportNRF24.h: No such file or directory
compilation terminated.

How to continue?

[pentti12]

Mortommy: Can you change your sketch so that it support MySensors 2.0 library?

[mortommy]

Hi @pentti12 ,
please find the sketch 2.0.0 in the project. I couldn't test it yet, I have converted it following the guidance and I just verified that it compiles successfully.

[pentti12]

Sorry, but the compiler found a missing library file:

MyTransportNRF24.h

MySensors library 2.0 has MyTransportNRF24.cpp only

[pentti12]

Hi

I changed my Arduino IDE 1.6.11 using the MySensors development library v2.1.0-beta. Now the compiling went OK. I will continue with that. It will take few days before I have more info about how things went with actual hardware.