Solar Powered Soil Moisture Sensor

[mrwomble]

I meant to mention that the wires coming out of the bottom are the wires that go to the soil moisture probes.

Here's the code in case anyone else would like it:

// Updated to v2.0 of Mysensors

// Enable debug prints
#define MY_DEBUG
#define MY_RADIO_NRF24

#include <MySensors.h>
#include <SPI.h>

#define round(x) ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
#define N_ELEMENTS(array) (sizeof(array)/sizeof((array)[0]))

#define CHILD_ID_MOISTURE 0
#define CHILD_ID_BATTERY 1
#define SLEEP_TIME 10000 // Sleep time between reads (in milliseconds), was 10000
#define THRESHOLD 1.1 // Only make a new reading with reverse polarity if the change is larger than 10%.
#define STABILIZATION_TIME 1000 // Let the sensor stabilize before reading default BOD settings
const int SENSOR_ANALOG_PINS[] = {A4, A5}; // Sensor is connected to these two pins. Avoid A3 if using ATSHA204. A6 and A7 cannot be used because they don't have pullups.

// MySensor gw;   //removed for v2.0
MyMessage msg(CHILD_ID_MOISTURE, V_HUM);
MyMessage voltage_msg(CHILD_ID_BATTERY, V_VOLTAGE);
long oldvoltage = 0;
byte direction = 0;
int oldMoistureLevel = -1;
float batteryPcnt;
float batteryVolt;
int LED = 5;

void setup()
{
  pinMode(LED, OUTPUT);
  digitalWrite(LED, HIGH);
  delay(200);
  digitalWrite(LED, LOW);
  delay(200);
  digitalWrite(LED, HIGH);
  delay(200);
  digitalWrite(LED, LOW);
  
  //  gw.begin(); //Removed for v2.0
  for (int i = 0; i < N_ELEMENTS(SENSOR_ANALOG_PINS); i++) {
    pinMode(SENSOR_ANALOG_PINS[i], OUTPUT);
    digitalWrite(SENSOR_ANALOG_PINS[i], LOW);
  }
}

void presentation(){  //created for v2.0
  sendSketchInfo("Plant moisture w solar", "1.0");
  present(CHILD_ID_MOISTURE, S_HUM);
  delay(250);
  present(CHILD_ID_BATTERY, S_MULTIMETER);
}


void loop()
{
  int moistureLevel = readMoisture();

  // Send rolling average of 2 samples to get rid of the "ripple" produced by different resistance in the internal pull-up resistors
  // See http://forum.mysensors.org/topic/2147/office-plant-monitoring/55 for more information
  if (oldMoistureLevel == -1) { // First reading, save current value as old
    oldMoistureLevel = moistureLevel;
  }
  if (moistureLevel > (oldMoistureLevel * THRESHOLD) || moistureLevel < (oldMoistureLevel / THRESHOLD)) {
    // The change was large, so it was probably not caused by the difference in internal pull-ups.
    // Measure again, this time with reversed polarity.
    moistureLevel = readMoisture();
  }
  send(msg.set((moistureLevel + oldMoistureLevel) / 2.0 / 10.23, 1));
  oldMoistureLevel = moistureLevel;
 
  int sensorValue = analogRead(A0);
  Serial.print("--Sensor value:");Serial.println(sensorValue);
  float voltage=sensorValue*(3.3/1023);
  Serial.print("--Voltage:");Serial.println(voltage);
  batteryPcnt = (sensorValue - 248) * 0.72;
  Serial.print("--Battery %:");Serial.println(batteryPcnt);
  batteryVolt = voltage;
  sendBatteryLevel(batteryPcnt);
  resend((voltage_msg.set(batteryVolt, 3)), 10);
  //send(voltage_msg.set(batteryVolt), 3);

  //flash led to indicate send
  digitalWrite(LED, HIGH);
  delay(200);
  digitalWrite(LED, LOW);
  
  sleep(SLEEP_TIME);
}

void resend(MyMessage &msg, int repeats)
{
  int repeat = 1;
  int repeatdelay = 0;
  boolean sendOK = false;

  send(msg);
/*
  while ((sendOK == false) and (repeat < repeats)) {
    if (send(msg)) {
      sendOK = true;
    } else {
      sendOK = false;
      Serial.print("Error ");
      Serial.println(repeat);
      repeatdelay += 500;
    } repeat++; delay(repeatdelay);
  }*/
}


int readMoisture() {
  pinMode(SENSOR_ANALOG_PINS[direction], INPUT_PULLUP); // Power on the sensor
  analogRead(SENSOR_ANALOG_PINS[direction]);// Read once to let the ADC capacitor start charging
  sleep(STABILIZATION_TIME);
  int moistureLevel = (1023 - analogRead(SENSOR_ANALOG_PINS[direction]));

  // Turn off the sensor to conserve battery and minimize corrosion
  pinMode(SENSOR_ANALOG_PINS[direction], OUTPUT);
  digitalWrite(SENSOR_ANALOG_PINS[direction], LOW);

  direction = (direction + 1) % 2; // Make direction alternate between 0 and 1 to reverse polarity which reduces corrosion
  return moistureLevel;
}

My thanks to flopp for the cool idea and to everyone else on the thread for the contributions.

[NeverDie]

Interesting project. To what degree, if any, has corrosion been a problem after you switched to soldered connections? Obviously the operating environment (near the ground outdoors) can be intrinsically humid.

Also, can someone please post a larger photo of how the sensor is attached at the base? The area of interest on the photo provided is miniscule, and it's too grainy if I try to enlarge it to a better size:

[NeverDie]

By the way, I notice this guy has a rather interesting soil moisture sensor that appears to go beyond measuring mere electrical conductance: https://www.tindie.com/products/Power_Modules/fdr-100mhz-plant-soil-sensor-mineral-transparency/

[AWI]

@flopp Can you please include the pictures in your posting as the "tinypic.com" is rather intrusive, thanks...

[flopp]

@NeverDie said:

Interesting project. To what degree, if any, has corrosion been a problem after you switched to soldered connections? Obviously the operating environment (near the ground outdoors) can be intrinsically humid.

I have not checked how the sensor look like now, but I have only run it for 6 months. I have always used soldered connections.

Also, can someone please post a larger photo of how the sensor is attached at the base?

[AWI]

@flopp Just copy the area's of intrest with a "snipping tool" (screen print) and copy in the post. Or, use one of the less intrusive services of the big cloud names...

[mrwomble]

@NeverDie
Interesting, but would make the project a little pricey.

[NeverDie]

@flopp
Perfect! Thanks a bunch. I like it. Very clever.

I think you were wise to cover the insulated wire with the silicon. Despite the appearance of being waterproof, I've noticed that regular wire insulation isn't waterproof/vaporproof, and regular wires used outdoors don't survive well (especially "copper" wires from China, which tend to have a high iron content and thus literally rust their way to failure). I don't know that silicon is sufficient, but if it isn't it might at least slow down the degradation process. It takes some effort to put these things together, so plainly you want them to last as long as possible.

Nice work!

[Nca78]

@NeverDie said:
I don't know that silicon is sufficient, but if it isn't it might at least slow down the degradation process.

Silicon is water proof, but not vapor proof. Else, it would not cure ;)

[flopp]

I have put glue on top of the soldering

[flopp]

WARNING!!!
I opened one of my items which didn't worked since many weeks ago.
I putted it on a table and should just open the stuff when I saw some brown water coming out from the pole.
My first guess was that it was water mixed with mud but the smell was strange. It can be that the battery has leaked.

If you will build this item please seal the battery to 100%. I just put the battery in the pole but unfortunately water came in and what I think destroyed the battery!

Be careful

[flopp]

Just wanna update you all how the battery has been since start.
No restart since 1st September.
A few days ago we moved the plant indoor and I forgot to take out the sensor, I moved the sensor outdoor the day after

[Huczas]

@flopp is your code should work with new version of gateway 2.1.1?
Just maked using this tutorial my gateway https://www.mysensors.org/build/raspberry and I'm getting nothing in debug...

pi@raspberrypi:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT

In node I used your newest code for gw2.0 - is this because version mismatch or something different in my setup?
Could you update your code to work with new version?

[flopp]

@Huczas
I don't use 2.1, yet. I only use 1.5.1.
I don't have any knowledge of 2.x, so I cannot update the code, sorry

[Huczas]

@flopp just release that @mrwomble was posting that updated code sorry. @mrwomble can you help?

[hiddenuser]

Hello All,
Wondering if any one of the successful implenters would be able to share their soil moisture graphs,both for a day and over months..

[dmonty]

To solve the battery discharge memory issue, could a second battery be added with logic to alternate between batteries and fully discharge one at a time?

[gohan]

Charge memory is a thing of the past, lithium batteries don't have it (if I understood what you meant).

[NeverDie]

@gohan said in Solar Powered Soil Moisture Sensor:

Charge memory is a thing of the past, lithium batteries don't have it (if I understood what you meant).

Except that, if I'm not mistaken, he's presently re-using the NiCd's that came with the original solar garden light.

[Edit: correction: I think maybe (?) he switched to Nimh. I didn't think those had a memory problem. Do they? ]

[Edit2: Maybe he'll "upgrade" to a supercap. :) A soil moisture meter would be a good application for one. ]

[gohan]

NiMh still have some charge memory but not as bad as the NiCd. I got the moisture sensors yesterday I have to test them the next days.
https://www.aliexpress.com/item/Soil-Moisture-Sensor/32532715392.html