Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Arduino based Serial Gateway compatible with Atmega32U4 based Arduino Micro?

jerseyguy1996 last edited by

First question: Is the GatewaySerial.ino sketch in 2.0.0 the sketch that replaced the SerialGateway.ino sketch from 1.5.4?

Second question: If so, is the GatewaySerial.ino sketch compatible with the Atmega32U4 based Arduino Micro (similar to the Arduino Leonardo)? Link to the arduino is below if you are not familiar with it.

https://www.arduino.cc/en/Main/ArduinoBoardMicro
Reply Quote 0
1 Reply Last reply

1
Posts

652
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50413
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

43
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Support for CC1101 radios
Hardware • • buxtronix

2

2
Votes

2
Posts

24
Views

Nice. I know there are RFM69's, but I've seen quite a few requests for the CC1101. Always good to have options. I did something similar with the WIO-E5 chips in my repo. The E5 is not quite ready for prime time, but the basics are working. I have many MySensors nodes, and still adding more. Good to see some new code for it.
Newbie questions
Hardware • • magwas

2

0
Votes

2
Posts

16
Views

Great project! With some guidance, KiCad and AVR will click again!
Newbie: confused by the jargon, needing simple guidance...
Hardware • newbie • • Meldrew's mate

6

0
Votes

6
Posts

32
Views

Gawd bless ya @OldSurferDude , that just about answered every question I have to date, I especially thank you for indicating whether the item named is a software or hardware product. On reading into the Cerbo GX capabilities I was very impressed with its sophistication and, just as you said, I will have to break the complicated parts down into bite-sized pieces and build from there. It started with an idea for a project, essentially to take data on battery state of charge (SoC) from the Cerbo GX and use an Arduino Nano or ESP8266 to build a strategy so that I would have sufficient hot water in the morning, consistent with having enough battery power left in the evening. Only on further inspection did it occur that the Node Red software built into the Cerbo GX could do this for me...and thus the possibility that a wireless hot water temperature sensor (transducer) could be fabricated to feed that data into the Cerbo GX; hence my path to here. I've dabbled in programming in C, mainly through the Arduino IDE, and in a previous life part of my work involved programming PLCs for industrial automation, so I am somewhat familiar with 'tech', but I lost interest once most systems seemed to go Windows based. In the intervening years the 'tech' has moved on apace and has left me behind, which is why I've struggled to follow the jargon, akin to trying to fit the second piece in a large jigsaw puzzle. Once the fundamentals are there I'll catch on. So please, kind contributors, be tolerant of the silly questions we newbies ask, we won't always be newbies, and I'll be back for sensors stuff once I've tamed the red-hot node and sorted out my LBQTTs Best wishes....MM
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3282
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !