rs485 on nano

[skatun]

@dbemowsk so i added the usb device, it produces gibberish:

~þx

different baud-rates, gibberish changes.....

gibberish from the node, but nothing from gateway, I also changed gateway to uno as a test without success, here is the code on gateway which i commented out:

// Flash leds on rx/tx/err
//#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
//#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
//#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3 

//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED

[dbemowsk]

@skatun

so i added the usb device, it produces gibberish:

When working with serial communication, gibberish means that your nodes are talking at different baud rates. Once you get the same baud on both ends, you should see something readable. What baud rate do you have your node set to for the software serial connection? Whatever that is set to is the baud rate that you need to set the USB device to. Once you get that communicating, then check the software serial baud on the gateway. The problem could be that you have differing baud rates on both. If that is the case, your gateway is seeing similar gibberish that you are seeing on your USB adapter and thus does not know what to do with it.

Another thing is that if you have your baud rate set too high, even though both sides are using matching baud rates, you can still see gibberish. Try starting everything on a lower baud like 9600. If that works, try the next baud rate, and the next. You may be able to run at 115200, but if you have debugging turned on it may have trouble communicating at that speed.

Also, don't confuse your hardware serial with your software serial. This is the hardware UART serial baud definition:

Serial.begin(115200);

And this is the software serial baud definition:

RS485Serial.begin(9600);

These do not necessarily need to match. It is the software serial at all points that need to match.

Let me know if any of that helps.

[consul58]

@skatun
Hi,
I found the solution.

Look at this

Place the following in your Node-Sketch e.g. for Node ID 23

 #define MY_NODE_ID 23

and the communication between node and Gateway is ok.

I hope this works for you.

[pjr]

@skatun did you got this working?
I faced similar situation when I was accidentally connected rx & tx wrong way around on my GW. The sensor node was constantly polling for parent but got no response.

The "gibberish" on RS485 bus might also be the control chars the transport uses.. SOH, STX, ETX and EOT.
See this post.

In my GW sketch I have these two enabled:

#define MY_INCLUSION_MODE_FEATURE
#define MY_INCLUSION_MODE_DURATION 60 

[skatun]

@pjr @consul58 Have been away the last 5 days, will update the thread with the result tomorrow. Can anyone lighten me up on benefit of having inclusion button, and what inclusion time should be set to?

[hek]

The inclusion mode was initially developed for Vera because it had the bad behaviour of needing a restart (of its main process) each time a device was added.

It is all a controller-side thing after all (all messages, including presentation is always passed to controller). But the mode can be turned on using a physical button on the gateway device. Which results in a message to controller saying start/stop inclusion mode.

[pjr]

Good to know. Think then I can throw that away since I'm using domoticz.

[skatun]

Implemented fixed node ID without success, I think maybe the rs485 adapter on gateway is broken, will test more tomorrow

[wimd]

@skatun Will join this discussion as well. I have exately the same issue. My set up is a nano as sensor and an uno as gateway.
I verified correct wiring of RS485 network is correctly doen I used this sketch (swith ReceiveOrSend to RS485Transmit or RS485Receive on both nodes;
:

#include <AltSoftSerial.h>

AltSoftSerial altSerial;
#define SSerialTxControl 2 //RS485 Direction control

#define RS485Transmit HIGH
#define RS485Receive LOW
bool ReceiveOrSend = RS485Transmit;

void setup() {

Serial.begin(9600);
Serial.println("AltSoftSerial Test Begin");
pinMode(SSerialTxControl, OUTPUT);
digitalWrite(SSerialTxControl, RS485Transmit); // Enable RS485 Transmit
altSerial.begin(9600);
if (ReceiveOrSend ){
Serial.println("send mode");
digitalWrite(SSerialTxControl, RS485Transmit); // Enable RS485 Transmit
} else
{
digitalWrite(SSerialTxControl, RS485Receive); // Enable RS485 Transmit
Serial.println("receive mode");
}
}

void loop() {
char receivedOnRS485;

if (ReceiveOrSend ){
altSerial.println(" Hello world");
delay(2000);
} else
{

if (altSerial.available()) {
receivedOnRS485 = altSerial.read();
Serial.print("ontvagen=");
Serial.println(receivedOnRS485);
}
}
}```

[dbemowsk]

@wimd As my reply stated in the other thread, it would be helpful to see all sketches being used so we can determine better where the problem may lie.

[wimd]

@dbemowsk It are the standard examples.

For the gateway (Uno) :

* The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 * The RS485 Gateway prints data received from sensors on the serial link. 
 * The gateway accepts input on seral which will be sent out on
 * the RS485 link.
 *
 * Wire connections (OPTIONAL):
 * - Inclusion button should be connected between digital pin 3 and GND  
 * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
 *
 * LEDs (OPTIONAL):
 * - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error 
 * 
 * The gateway uses AltSoftSerial to handle two serial links 
 * on one Arduino. Use the following pins for RS485 link
 * 
 *  Board          Transmit  Receive   PWM Unusable
 * -----          --------  -------   ------------
 * Teensy 3.0 & 3.1  21        20         22
 * Teensy 2.0         9        10       (none)
 * Teensy++ 2.0      25         4       26, 27
 * Arduino Uno        9         8         10
 * Arduino Leonardo   5        13       (none)
 * Arduino Mega      46        48       44, 45
 * Wiring-S           5         6          4
 * Sanguino          13        14         12
 * 
 */

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin 
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED

#include <SPI.h>
#include <MySensors.h>  

void setup() { 
  // Setup locally attached sensors
}

void presentation() {
 // Present locally attached sensors 
}

void loop() { 
  // Send locally attached sensor data here 
}

For the sensor (Nano):

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 * 
 * DESCRIPTION
 * This is an example of sensors using RS485 as transport layer
 * 
 * Motion Sensor example using HC-SR501 
 * http://www.mysensors.org/build/motion
 * 
 * The transport uses AltSoftSerial to handle two serial links 
 * on one Arduino. Use the following pins for RS485 link
 * 
 *  Board          Transmit  Receive   PWM Unusable
 * -----          --------  -------   ------------
 * Teensy 3.0 & 3.1  21        20         22
 * Teensy 2.0         9        10       (none)
 * Teensy++ 2.0      25         4       26, 27
 * Arduino Uno        9         8         10
 * Arduino Leonardo   5        13       (none)
 * Arduino Mega      46        48       44, 45
 * Wiring-S           5         6          4
 * Sanguino          13        14         12 * 
 * 
 */


// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin 
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

#include <SPI.h>
#include <MySensors.h>

unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define CHILD_ID 1   // Id of the sensor child

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()  
{  
  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Motion Sensor", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_MOTION);
}

void loop()     
{     
  // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
        
  Serial.println(tripped);
  send(msg.set(tripped?"1":"0"));  // Send tripped value to gw 

  // Sleep until interrupt comes in on motion sensor. Send update every two minute.
  sleep(digitalPinToInterrupt(DIGITAL_INPUT_SENSOR), CHANGE, SLEEP_TIME);
}

[skatun]

@wimd include debug and remove inclusion from the sketches and it should be ok. I have ordered new rs485 shield, i expect that to be the issue..

[bocmau]

@consul58 said:

#define MY_NODE_ID 23

Thanks for the tip now works

[wimd]

@skatun include debug, removal of inclusion and define MY_NODE_ID enabled communication on the RS485 bus.

[Reza]

This post is deleted!

[Reza]

@skatun my problem is solve . you test this and feedback me. use 3.3v and gnd pins in arduino use for rs485 module.

[Reza]

is this wiring true for rs485 ? thank you

also which cable is appropriate for A and B?

[b0rmann]

@Reza

no. rs485 must have LINEAR BUS topology.

[Reza]

@b0rmann my pic is not a bus ? i think this is a bus topology !

[Reza]

@b0rmann
this is a bus ?

so in end of A and B , what am i do ?