Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

NRF24L01 and rfm69 in one gateway

Omemanti last edited by

Hey There,

Now I got multiple sensors using a NRF24L01. I'm of to a new journey, the rfm69.

Is there a way to combine bothe radios in one gateway?
I use an esp8266(node-UMC) with NRF24L01. Haven't got a spare esp lying around..

Thnx!
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by @Omemanti

@Omemanti sorry, only one transport type per gateway is supported.

Maybe you have a spare Arduino to create a serial gateway?

In either case I would recommend ordering a few esp. I use the wemos d1 mini version. Cheap and easy to use
Reply Quote 0
1 Reply Last reply
Omemanti last edited by @mfalkvidd

@mfalkvidd oké, clear!
Unfortunate.
Guess a couple esp8266 couldn't hurt.
Reply Quote 1
1 Reply Last reply

gateway 101 nrf24 15 rfm69hw 12

3
Posts

1593
Views

Log in to reply

Suggested Topics

MySensors plugin : Cannot send command - communications error
Troubleshooting • gateway ethernet • • BulldogLowell

20

0
Votes

20
Posts

9283
Views

@5546dug Yes I think you need 1.4.1 or latest. The messages you see (0;0;3;9...) are traffic in the wireless sensor network. My problem appeared again. The EthernetGateway responds to Ping but Vera plugin says: "Cannot send command - communications error" So perhaps increasing power could help, but how? Is adding capacitors enough?? Like for the radio there already is one..
How to use additional SPI device with RFM69 repeater node?
General Discussion • rfm69hw spi ade7763 • • jkandasa

5

0
Votes

5
Posts

2204
Views

@skywatch @mfalkvidd Thank you for your comments. I am using Moteino R4 and RFM69 connected to hardware SPI pins. I tried the same pin with softSPI, but I could not get success. Now I have altered the ADE7763 Arduino library to update SPI settings on every call. And added code to update the only flag on ADE7763 interrupt(like we have in RFM69_new library). Seems all look somewhat ok. I think for RFM69 we use a default clock speed. for ADE7763: SPI_CLOCK_DIV4 Are you using pull up resistors on the CS lines to each device - that might be worth a try too.... Yes, I have
💬 HALO : ESP32 multi transport GW/Bridge for Mysensors
OpenHardware.io • gateway rfm69 wifi nrf24 bluetooth ble esp32 rgb rfm95 bridge blaster serial wi-fi sniffer can • • openhardware.io

40

4
Votes

40
Posts

11223
Views

@scalz said in HALO : ESP32 multi transport GW/Bridge for Mysensors: the webapp was great, but I converted it to native crossplatform app for better versatility&perf, so I can use one app for my devices, like Ethernet for HALO etc, or Serial for my other Janus gw dongle, bluetooth.. To be honest, I've not updated anything yet for a few reasons, like very little spare time for a public release + support for such "big" project. (easier to handle local projects). Sorry, still no eta for the moment.. It is clear that there is not enough time. But this project can become popular. That's what's missing MySensors. ...This void must be filled.
Ethernet gateway troubleshooting advice
Troubleshooting • gateway nrf24l01+ vera ethernet w5100 • • jkbrowne

69

0
Votes

69
Posts

38807
Views

Sorry for the huge kick.. But I seem to have the same ethernet gateway as TS. His his wire diagram valid?
Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
[SOLVED] W5100 Gateway code modification
General Discussion • gateway nrf24l01 • • fejt

3

0
Votes

3
Posts

1094
Views

@mfalkvidd Thank you! It works. I was searching for "A0" not the GPIO number (newbie here) Thank you once again.
Newbie question about how the mysensors gateway connects to controller
General Discussion • gateway serial gateway ethernet gateway • • Thomas433

3

0
Votes

3
Posts

39
Views

@Boots33 Thanks a lot for the quick response. I now have my Nano running as a serial gateway and it is connected via a USB cable directly to my controller (Raspberry Pi 4 running Home Assistant / Hass.io). I added a local motion sensor to the Nano gateway HW and pasted the mysensors MotionSensor example code to the setup(), presentation() and loop() functions as well as to the definitions in the top of the GatewaySerial example code. I disabled the radio definitions as I currently have no radio capability in my gateway (not sure if this was necessary). In Home Assistant / Hass.io I updated the configuration.yaml with the following text (as described on the Home Assistant integration help): mysensors: gateways: - device: '/dev/ttyUSB0' And it works In Home Assistant Developer Tools under States I can now see my motion sensor go on and off by the flick of my hand. I had expected a bit more bumps on the road just to get this far, but wow - I am obviously walking in the foot prints of people who have worked hard to make it easy for the rest of us. I am sure I will hit bumps on the way when the radios have to send results to the gateway (thick concrete walls with lots of steel), but for now I will enjoy this big success. Thanks again Boots33
all the gear, no idea
General Discussion • gateway vera help newbie • • baldsi

10

0
Votes

10
Posts

4663
Views

@maltimus - thanks, I can see the picture. frstratingly I have the Vera Edge though!

57
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1