nRF5 action!

NeverDie

I don't remember. I've lately been using LoRa modules, plus getting distracted by CNC, so my nRF5 work has been on hold. I'm hoping that d00616 continues to work on the software though so that more than one nRF5 interrupt can be active at a time.

korttoma

@nca78 thanks for the hint.

I tried to merge my sketch with the code provided by @NeverDie but I can not seem to get it to detect my button and I don't quite understand where I should attach my button that is on pin 28 to the interrupt thingie.

Here is my code now:

//This sketch is applicable to Coincell Multisensor nRF51822, version 10

// Define a static node address, remove if you want auto address assignment
//#define MY_NODE_ID 26                                                          // Kök
#define MY_NODE_ID 27                                                          // Test device
                                                  

// Enable and select radio type attached

#define MY_RADIO_NRF5_ESB

#define SN "NRF5 Scene"
#define SV "1.0"

#define CHILD_ID_SCENE 1

//#define MY_CORE_ONLY


#define IS_NRF51  //true iff the target is an nRF51.  If an nRF52, then comment this line out!

// PIN for the buttons
byte buttonOne = 28;

//Bounce debouncer[NUMBUTTONS];
int buttonOneoldValue;


// Pin definitions
//#define DIGITAL_INPUT_INT 28   // The digital input you attached your interrupt  (Only 2 and 3 generates interrupt!)


//#define I2C_INTERRUPT_PIN PIN_BUTTON1
//#define LEAK_DETECTION_PIN PIN_BUTTON1

#include <nrf.h>
#include <MySensors.h>

volatile bool button_pressed=false;

// Sensor messages
MyMessage msgOn(CHILD_ID_SCENE, V_SCENE_ON);

// Global settings
uint16_t SceneOne = 0;
uint16_t SceneTwo = 1;

void blinkityBlink(uint8_t pulses, uint8_t repetitions) {
  for (int x=0;x<repetitions;x++) {
    for (int i=0;i<pulses;i++) {
      digitalWrite(LED_BUILTIN,HIGH);
      wait(20);
      digitalWrite(LED_BUILTIN,LOW);
      wait(100);
    }    
      wait(500);
  }
}

void disableNfc() {  //only applied to nRF52

#ifndef IS_NRF51
  //Make pins 9 and 10 usable as GPIO pins.
  NRF_NFCT->TASKS_DISABLE=1;  //disable NFC
  NRF_NVMC->CONFIG=1;  // Write enable the UICR
  NRF_UICR->NFCPINS=0; //Make pins 9 and 10 usable as GPIO pins.
  NRF_NVMC->CONFIG=0;  // Put the UICR back into read-only mode.
#endif
}


void turnOffRadio() {
  NRF_RADIO->TASKS_DISABLE=1;
  while (!(NRF_RADIO->EVENTS_DISABLED)) {}  //until radio is confirmed disabled
}

void turnOffUarte0() {
#ifndef IS_NRF51  
  NRF_UARTE0->TASKS_STOPRX = 1;
  NRF_UARTE0->TASKS_STOPTX = 1;
  NRF_UARTE0->TASKS_SUSPEND = 1;
  NRF_UARTE0->ENABLE=0;  //disable UART0
  while (NRF_UARTE0->ENABLE!=0) {};  //wait until UART0 is confirmed disabled.
#endif

#ifdef IS_NRF51
  NRF_UART0->TASKS_STOPRX = 1;
  NRF_UART0->TASKS_STOPTX = 1;
  NRF_UART0->TASKS_SUSPEND = 1;
  NRF_UART0->ENABLE=0;  //disable UART0
  while (NRF_UART0->ENABLE!=0) {};  //wait until UART0 is confirmed disabled.
#endif
}

void turnOffAdc() {
#ifndef IS_NRF51
  if (NRF_SAADC->ENABLE) { //if enabled, then disable the SAADC
    NRF_SAADC->TASKS_STOP=1;
    while (NRF_SAADC->EVENTS_STOPPED) {} //wait until stopping of SAADC is confirmed
    NRF_SAADC->ENABLE=0;  //disable the SAADC
    while (NRF_SAADC->ENABLE) {} //wait until the disable is confirmed
  }
#endif
}


void turnOffHighFrequencyClock() {
    NRF_CLOCK->TASKS_HFCLKSTOP = 1;
    while ((NRF_CLOCK->HFCLKSTAT) & 0x0100) {}  //wait as long as HF clock is still running.
}


void mySleepPrepare()
{
  turnOffHighFrequencyClock();
  turnOffRadio();
  turnOffUarte0();
}
 

void activateLpComp() {
  //NRF_LPCOMP->PSEL=1; // monitor AIN1 (pin P0.03 on nRF52832 test board).
  //while (!(NRF_LPCOMP->PSEL==1)) {} //wait until confirmed
  NRF_LPCOMP->PSEL=3; // monitor AIN3 (pin P0.02 on nRF51822 for coincell_multisensor_v10)
  while (!(NRF_LPCOMP->PSEL==3)) {} //wait until confirmed
  NRF_LPCOMP->REFSEL=1;  // choose 1/4 VDD as the reference voltage
  while (!(NRF_LPCOMP->REFSEL==1)) {} //wait until confirmed
  NRF_LPCOMP->ANADETECT=1;  //detect UP events.
  while (NRF_LPCOMP->ANADETECT!=1) {} //wait until confirmed
  NRF_LPCOMP->INTENSET=B0100;  //Enable interrupt for UP event
  while (!(NRF_LPCOMP->INTENSET==B0100)) {} //wait until confirmed
  NRF_LPCOMP->ENABLE=1;  //Enable LPCOMP
  while (!(NRF_LPCOMP->ENABLE==1)) {} //wait until confirmed
  NRF_LPCOMP->TASKS_START=1;  //start the LPCOMP
  while (!(NRF_LPCOMP->EVENTS_READY)) {}  //wait until ready
  
  NVIC_SetPriority(LPCOMP_IRQn, 15);
  NVIC_ClearPendingIRQ(LPCOMP_IRQn);
  NVIC_EnableIRQ(LPCOMP_IRQn);
}

void suspendLpComp() { //suspend getting more interrupts from LPCOMP before the first interrupt can be handled
  if ((NRF_LPCOMP->ENABLE) && (NRF_LPCOMP->EVENTS_READY)) {  //if LPCOMP is enabled
    NRF_LPCOMP->INTENCLR=B0100;  //disable interrupt from LPCOMP
    while (NRF_LPCOMP->INTENCLR==B0100) {} //wait until confirmed
  }
}

void resumeLpComp() { //suspend getting interrupts from LPCOMP
  NRF_LPCOMP->INTENSET=B0100;  //Enable interrupt for UP event
  while (!(NRF_LPCOMP->INTENSET==B0100)) {} //wait until confirmed
}

/****************************************************
 *
 * Setup code 
 *
 ****************************************************/
 
void setup() {

  hwInit();
  hwPinMode(LED_BUILTIN,OUTPUT_D0H1);
  disableNfc();
  turnOffAdc();
  activateLpComp();
  blinkityBlink(2,1);  //Signify end of setup with two quick pulses.
  mySleepPrepare();
  button_pressed=false;

  //NRF_CLOCK->INTENSET=B11;  //enable interrupts for EVENTS_HFCLKSTARTED and  EVENTS_LFCLKSTARTED
 // NRF_CLOCK->TASKS_HFCLKSTART=1;  //start the high frequency crystal oscillator clock
 // while (!(NRF_CLOCK->EVENTS_HFCLKSTARTED)) {} //wait until high frequency crystal oscillator clock is up to speed and working
                                                
  //hwPinMode(DIGITAL_INPUT_INT, INPUT_PULLUP);
    
    /// Make input & enable pull-up resistors on switch pins
  hwPinMode(buttonOne, INPUT_PULLUP);
  //buttonOneoldValue = -1;
  

  //sendBattLevel();
  

}

void presentation()  {
  sendSketchInfo(SN, SV);
  //present the scene controller to gateway
  wait(10);
  present(CHILD_ID_SCENE, S_SCENE_CONTROLLER);
      
  wait(10);
  sendBattLevel();
  
}

void sendBattLevel()
{
    long vcc = hwCPUVoltage();
  
    // Calculate percentage

    vcc = vcc - 1800; // subtract 1.9V from vcc, as this is the lowest voltage we will operate at
    
    long percent = vcc / 14.0;
    sendBatteryLevel(percent);    
  
}

void loop() {

  sleep(10000);  //sleep for 5 seconds.
  mySleepPrepare();  //An ounce of prevention: Turn-off HF clock, etc, ASAP to save power, just in case the library's sleep() routine resumed them.
  if (button_pressed) {   //if a leak is detected
    suspendLpComp(); //suspend LPCOMP to prevent multiple interrupts
    //blinkityBlink(10,3);  //blink a lot to show that a leak was detected.
    send(msgOn.set(SceneOne));
        
        wait(20);

        send(msgOn.set(SceneTwo));

        sendBattLevel();
    button_pressed=false;  //Clear the semaphore
    NRF_LPCOMP->EVENTS_UP=0;  //Clear the semaphore
    resumeLpComp();  //operations of LPCOMP were suspended after detecting the LPCOMP iterrupt
  }
  else {
    blinkityBlink(1,1);  //otherwise, just one short blink to indicate the wakeup was scheduled by the RTC
  }
}


// * Reset events and read back on nRF52
//* http://infocenter.nordicsemi.com/pdf/nRF52_Series_Migration_v1.0.pdf
 
#if __CORTEX_M == 0x04
#define NRF5_RESET_EVENT(event)                                                 \
        event = 0;                                                                   \
        (void)event
#else
#define NRF5_RESET_EVENT(event) event = 0
#endif


// This must be in one line
extern "C" { void LPCOMP_IRQHandler(void) {button_pressed=true; NRF5_RESET_EVENT(NRF_LPCOMP->EVENTS_UP); NRF_LPCOMP->EVENTS_UP=0; MY_HW_RTC->CC[0]=(MY_HW_RTC->COUNTER+2);}}

I thought that I should do it like this:

void activateLpComp() {
   NRF_LPCOMP->PSEL=28; // monitor AIN3 (pin P0.02 on nRF51822 for coincell_multisensor_v10)
  while (!(NRF_LPCOMP->PSEL==28)) {} //wait until confirmed

But then it does not seem to run the loop anymore because I do not get the 10s blink.

Toyman

Guys, help me understand: when do I need to enable DC-DC?
My breakout board consists of Ebyte module and a couple of buttons. Battery is CR2450 directly connected to the module.
Do I need DC-DC?

NeverDie

@toyman With DC-DC, it uses roughly half the current during Tx and Rx. Seems like a no brainer to me, but you don't literally "need" to have it. I'm not aware of any downsides to it.

Toyman

@neverdie thx. What is needed hardware-wise? Two inductors between dc and dec4? Like in your breakout board?

NeverDie

@toyman Correct. You can review the schematic for this project: https://www.openhardware.io/view/472/Ebyte-nRF52832-Prototyping-Board

korttoma

I guess this is why I cant get LPCOMP to work on the device.

Eight input options (AIN0 to AIN7)

I would have to use the analog inputs because pin 28 is just a general purpose I/O pin.

Toyman

ebyte module is currently on sale at roughly $2.5
Total bargain!

Nca78

@korttoma using MySensors NRF5 boards you should be able to assign one AINx pin to physical pin 28.
The index you need to put in the code is the AIN index not the pin number.

korttoma

@nca78 sorry but I cannot figure out how to do this. Should I do it in the MyBoardNRF5.cpp, MyBoardNRF5.h or in the sketch?

Nca78

@korttoma sorry I said stupid things as I'm a beginner too, you can't reassign analog inputs and LPCOMP to different pins on NRF5 chips.

korttoma

@nca78 it is ok, I think I will have to set up a test system with a different device with witch I can measure current consumption, attach serial logging and then try to fiddle with the code. I'm flying in the dark with this bluetooth beacon device since I cannot access any pins.

Toyman

@neverdie thx. Why don't you have a capacitor between DEC4 to GND? I can see only 2 inductors, while Nordic power guidelines prescribe an LC filter between DCC and DEC, ie inductors and a capacitor. nrf52dk also has it.

NeverDie

@toyman I guess I made an error then. Thanks for pointing that out. In general, I haven't gotten much feedback on the PCB's that I've posted, so any feedback is always appreciated. :)

Omemanti

@neverdie Question is, did the DC/DC still work without the cap?

NeverDie

@omemanti said in nRF5 Bluetooth action!:

@neverdie Question is, did the DC/DC still work without the cap?

I believe it did. If you look at: https://www.openhardware.io/view/471/Ebyte-nRF52832-Small-Breakout-Board
which has the inductors soldered on, I believe that is the one that I tested. Enough time has passed though that I can't be 100% sure now. I made a number of different variations, and I didn't post all of them.

Omemanti

@neverdie said in nRF5 Bluetooth action!:

nough time has passed though that I can't be 100% sure now. I made a number of different variations, and I didn't post all of them

I used your schematic for a PCB I ordered yesterday :), did saw the post about the cap until it was too late :(
part of the game!

Edit: according to your post https://forum.mysensors.org/topic/6961/nrf5-bluetooth-action/797 it did work

Nca78

@nca78 said in nRF5 Bluetooth action!:

I will try it on my board (using a module with QFAAH0) tomorrow, if power consumption is as low as expected I'll try on the beacon board.

@NeverDie I have tried the sketch nearly unchanged (only changed to lines because I use pin P0.01 so AIN2) and my current consumption is a bit over 30uA, do you have any idea of what I should check ? (I tried with both versions 0.1 and 0.3 of MySensors NRF5 boards).
At the moment my board only has a led and a DRV5032FB (<<1uA) in addition to the nrf51 module.

Toyman

Just to close the loop on DC-DC:

http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832.ps.v1.1%2Fpower.html&anchor=concept

Figure 2

NeverDie

@nca78 said in nRF5 Bluetooth action!:

do you have any idea of what I should check ?

Have you tried disabling serial?

nRF5 action!

23

11.7k

11.2k

113.0k