Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 Uniflächentaster PCB

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/419/Uniflachentaster-PCB
Reply Quote 0
1 Reply Last reply
Blauhorn last edited by
Hello Tilman, this is really a very nice design. I have ordered a pack of PCBs from elecrow, based on your gerber files, and have a few questions:
- in your BOM you have listed 5 smd-capacitors and 7 smd resistors, but on the PCB i have solderpads for 6 capacitors and 8 resistors. Can you just explain?
- is there a uniflächentaster-model for 2 ways?
- i think i have to flash the bootloader first, do you have a tutorial for this, and a sample-sketch for the board?
Thank you very much
Reply Quote 0
1 Reply Last reply

mysensors 189 temperature 58 battery 43 humidity 39 switch 28

2
Posts

2051
Views

Log in to reply

Suggested Topics

💬 MySensors ESP8266 MQTT gateway
OpenHardware.io • mysensors gateway esp8266 contest2017 • • openhardware.io

7

3
Votes

7
Posts

1330
Views

@Roland-Wijnen Hi! Were you able to compile the available files? I tried, but there has been a lot of error!
💬 MySWeMosGWShield - WeMos Mini MySensors Gateway Shield
OpenHardware.io • mysensors gateway nrf24l01 rfm69 esp8266 contest2017 wemos • • openhardware.io

40

0
Votes

40
Posts

10594
Views

What are the parameters of this radio, I could not get it to work. Suspicions that he had no speed 250.
💬 Easy Switch Box
OpenHardware.io • mysensors arduino switch atmega328 lora low power • • openhardware.io

1

0
Votes

1
Posts

19
Views

No one has replied
💬 Battery Powered Sensors
Announcements • battery • • hek

347

0
Votes

347
Posts

66932
Views

@nekitoss I used 3.3V pro mini with regulator removed and powered by Vin pin. Also removed leds from the pro mini. I used minicore bootloader. I used the small pir sensors and again removed the regulator to power directly from the pro mini outputs. After that sleep the node and trigger on interrupt. Send battery level once a day. Use inbuilt battery level monitor and not external components that constantly drain power to get battery level. 1.8V is 0% on the graph (not visible yet!) but I have had nodes working below 1.7V It's a matter of luck with that it seems. Hope this helps you on the right track. I'll try and help if you want. This is the latest image and still going strong after 18 months. Voltage is at 2.903V Here is photo of the test example - I need to make a case and produce more of them over winter..... Here is the same build/code of a window sensor. Similar time frame but hardly triggered.....
💬 Wirsbo/uponor thermostat
OpenHardware.io • mysensors temperature thermostat floor heating uponor wirsbo • • openhardware.io

8

2
Votes

8
Posts

4888
Views

I am non technical but I have 8 wirsbo stats in my house. One of them is faulty and the unit is now obsolete. Is it possible to purchase one of these pcbs and use it to replace the one in the faulty stat ? Thanks Richard
💬 Openhab 2 Mysensors smart chicken coop
OpenHardware.io • mysensors nrf24l01 openhab contest2017 ds18b20 pir dht22 rpi gateway mega 2560 limit switch chicken coop • • openhardware.io

1

0
Votes

1
Posts

959
Views

No one has replied
💬 jModule2
OpenHardware.io • mysensors contest2017 • • openhardware.io

11

0
Votes

11
Posts

2705
Views

@Andrew-Currie Downloaded KiCad and used it to import jBoard2.brd and output .gbr files via Plots plus the .drl file. Checked using GerbView and uploaded to PCBWay. Hopefully this will now work...
💬 BlackCircle Sensor - High "WAF" Temp/Hum. sensor
OpenHardware.io • mysensors temperature humidity contest2017 waf • • openhardware.io

13

0
Votes

13
Posts

3766
Views

@bisschopsr said in BlackCircle Sensor - High "WAF" Temp/Hum. sensor: Hi All, Like the design thinking of this, although an older topic I did manage to get me one of these dishes. After taking it apart, I have one question that came to mind. Is the ventilation in the dish enough for the humity sensor? Is there any experience with that after running this sensor for a while? Thx Ralph Hello, yes I think it's enough, in fact there's much more ventilation than in many commercial sensors which only have a small hole. But it's a good test to make, I'll try to compare to a sensor out of it's enclosure to see if there's significant difference or delay.

75
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1