Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 Uniflächentaster PCB

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/419/Uniflachentaster-PCB
Reply Quote 0
1 Reply Last reply
Blauhorn last edited by
Hello Tilman, this is really a very nice design. I have ordered a pack of PCBs from elecrow, based on your gerber files, and have a few questions:
- in your BOM you have listed 5 smd-capacitors and 7 smd resistors, but on the PCB i have solderpads for 6 capacitors and 8 resistors. Can you just explain?
- is there a uniflächentaster-model for 2 ways?
- i think i have to flash the bootloader first, do you have a tutorial for this, and a sample-sketch for the board?
Thank you very much
Reply Quote 0
1 Reply Last reply

mysensors 191 temperature 58 battery 44 humidity 39 switch 28

2
Posts

2051
Views

Log in to reply

Suggested Topics

💬 Usb serial Mysensors Gateway
OpenHardware.io • mysensors gateway mysensor passerelle de mysensors • • openhardware.io

1

0
Votes

1
Posts

260
Views

No one has replied
Testing battery level with regulator removed
Hardware • battery • • 4994james

6

0
Votes

6
Posts

50
Views

@4994james or just use internal vcc measurement as described on the same page. That saves you the voltage divider. I wrote a convenient library to measure vcc internally : https://github.com/Yveaux/Arduino_Vcc
💬 jModule
OpenHardware.io • mysensors contest2016 • • openhardware.io

84

7
Votes

84
Posts

34381
Views

@Dwalt Thank you very much, now I understand better why the measurement of the voltage on input A0 was never good ..
💬 HVAC Recuperator control
OpenHardware.io • mysensors hvac recuperator • • openhardware.io

1

0
Votes

1
Posts

24
Views

No one has replied
FOTA possibilities for remote sensor network
General Discussion • mysensors • • NielBierman

2

0
Votes

2
Posts

39
Views

In general, yes, the MySensors framework (library?) should support FOTA a couple different ways (read more at link). Were you aware of this, or is there some problem with your particular hardware? @NielBierman said in FOTA possibilities for remote sensor network: Raspberry pi I don't know yet whether you even need to change your gateway from microcontroller (uC) to Single Board Computer (SBC) or not. However if you do (or are looking for a controller, or whatever), by all means, please do yourself (and all of us) a favor and do a little more research as there are lots of better options out there for SBC nowadays, than RPi! For me, uC have been fine for gateway although I do use some SBC for controllers, MQTT broker, and various other GNU/Linux based servers/services and they are wonderful for that. But perhaps your needs are different from mine.
Need help with Code. Simple Nod with 4 button's and 2 Led output. Cant get he Led to work as I whant. They respond but both lights
My Project • mysensors • • Knightan

2

0
Votes

2
Posts

10
Views

@Knightan I believe that your problem may be related to this block of code. See my thoughts as comments.... if (message.type == V_STATUS) { //This is true for all messages received // Change relay state state_1 = message.getBool(); //This sets state for state_1 to the received value. digitalWrite(LED_PIN_Channel_1, state_1?RELAY_1_ON:RELAY_1_OFF); // Store state in eeprom saveState(CHILD_ID_5, state_1); // Write some debug info Serial.print("Incoming change for sensor: STATE 1"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } if (message.type == V_STATUS) { // Change relay state state_2 = message.getBool(); //This sets state for state_2 to the received value. digitalWrite(LED_PIN_Channel_2, state_2?RELAY_2_ON:RELAY_2_OFF); // Store state in eeprom saveState(CHILD_ID_6, state_2); // Write some debug info Serial.print("Incoming change for sensor: STATE 2"); Serial.print(message.sensor); Serial.print(", New status: "); Serial.println(message.getBool()); } It seems to me that state_1 = message.getBool(); AND state_2 = message.getBool(). So they both get set to the incoming value. I think you need to not set both to the same value and instead differentiate them to unique values. I could be wrong as I have not had chance to do anything related to mysensors for a long time now - I also don't use Domoticz. Have a look at the code on this page, it might help you a lot.... https://www.mysensors.org/build/relay
MySensors Mini Scene Controller
OpenHardware.io • mysensors arduino battery contest2016 • • openhardware.io

4

3
Votes

4
Posts

2231
Views

Thats perfect.. definitely have to try this.. Thanks!!
💬 Arduino Pro Mini Shield for RFM69(H)W
OpenHardware.io • arduino rfm69 temperature sensor humidity pcb atmega328 atmega328p si7021 rfm69hw wireless bme280 pressure interstitial • • openhardware.io

53

1
Votes

53
Posts

11590
Views

@gohan said in Arduino Pro Mini Shield for RFM69(H)W: If I remeber right that pin is used as input so the RFM69 is not receiving any 5v signal. In addition there are people claming they have the RFM69 module working on 5v on data pins and 3.3v on vcc, but I hardly suggest to do it. thank you just what i thought . about direct 5v on data...well... i seen a big red sign saying n :DONT do it! lol Level converters are so cheap...that i ordered 5 or 10 thoguether with rfm69 board. sorry about hijack this topic, i though i was on general discussion

14
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1