Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Multiple Motions/Doors

bluezr1 last edited by bluezr1

This post is deleted!
Reply Quote 0
1 Reply Last reply
bluezr1 last edited by @bluezr1

This post is deleted!
Reply Quote 0
1 Reply Last reply

2
Posts

574
Views

Suggested Topics

Hunter ceiling fan/light controller
General Discussion • • dbemowsk

1

0
Votes

1
Posts

447
Views

No one has replied
Count people entering/leaving a shop?
General Discussion • • TommySharp

2

0
Votes

2
Posts

811
Views

I used a cheap ebay infrared door minder in my parking sensor it seems to work very well for the price.
Need a recommendation for 1/2 AA batteries
General Discussion • • alexsh1

5

0
Votes

5
Posts

1314
Views

I'm using them, I got the ones from soshine and the stated capacity is just a little more than the one measured by the charger.
What is loaded / running on the arduino?
General Discussion • • Mr_sensor

4

0
Votes

4
Posts

939
Views

Arduino IDE can only program chip, not read its program memory. But you can use AVRDUDE ( maybe with some GUI ) for reading program memory from your chip. And in your program sketch define some string to identify version. It can be read hex output of program memory then.
Advisory: put IOT devices on a separate LAN/vLAN for better security
General Discussion • • NeverDie

40

1
Votes

40
Posts

343
Views

@NeverDie said in Advisory: put IOT devices on a separate LAN/vLAN for better security: @monte https://www.ebay.com/itm/X10SLH-N6-ST031-Supermicro-E3-1200-v3-LGA1150-Motherboard-3x-X540-T2-6x-10GbE/184546263249?hash=item2af7d080d1:g:CCUAAOSwoP1gSWhO Lest I mislead anyone, I subsequently contacted to the seller and, despite the wording, it doesn't include an E3-1200 with the board. He just meant that as shorthand to refer to the processor family that's compatible with the board. That said, there are a ton of inexpensive used LGA1150 CPU's on ebay that could serve the purpose.
garage doors sensor not working good
General Discussion • • laoadam

4

0
Votes

4
Posts

724
Views

@laoadam Your garage door safety sensors may not be aligned quite right. It could be off just enough that vibration from the door itself when opening and closing is knocking one of the sensor modules out of alignment. The same could be true if one of the wires to it is loose. Check both sensor modules to make sure they are aligned right and not loose. One should be a transmitter that shoots a beam to the other module which is the receiver. If the transmitter beam is not aligned exactly right with the receiver, it won't work. As I mentioned too, check that there are no loose or broken wires. If wires go to screw terminals, make sure those are secured properly and that none of the wire casing is getting pinched in with the wire as that may cause a partial connection that could be lost with vibration of the door. With all that being said, this is a forum for a DIY home automation hardware platform called MySensors. Were you planning at some point to implement this for your garage door?
Method to reveal sketch inside node or g/w
General Discussion • arduino vera ide • • 5546dug

6

0
Votes

6
Posts

2833
Views

@LastSamurai good idea! Will give it a go!
Using loop function with MySensors-master/examples/ (2.2)
General Discussion • • eric007

12

0
Votes

12
Posts

1944
Views

Great work @eric007, thanks for reporting back!