Having trouble with my RPI MQTT gateway talking to my first sensor
-
Hello,
Finally got my radios working properly with my RPI Gateway. I'm now having problems with my first homemade DHT11 Sensor which is connected to a NANO V3 with a NRF24 radio connecting to my gateway and talking. Both Radios have a 47uF Capacator between the VCC and GND on the Radio
I used the code in http://smarthomeblog.net/diy-home-automation-sensors-first-node/
This is what I'm getting in the Serial Monitor of Arduino ..
16 MCO:BGN:INIT NODE,CP=RNNNA---,VER=2.2.0
25 TSM:INIT
26 TSF:WUR:MS=0
33 TSM:INIT:TSP OK
35 TSM:INIT:STATID=1
40 TSF:SID:OK,ID=1
43 TSM:FPAR
1642 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
3649 !TSM:FPAR:NO REPLY
3651 TSM:FPAR
5251 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
7258 !TSM:FPAR:NO REPLY
7260 TSM:FPAR
8859 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
10866 !TSM:FPAR:NO REPLY
10868 TSM:FPAR
12468 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
14476 !TSM:FPAR:FAIL
14477 TSM:FAIL:CNT=1
14479 TSM:FAIL:DIS
14481 TSF:TDI:TSL
24484 TSM:FAIL:RE-INIT
24486 TSM:INIT
24494 TSM:INIT:TSP OK
24496 TSM:INIT:STATID=1
24498 TSF:SID:OK,ID=1
24500 TSM:FPAR
26099 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
28107 !TSM:FPAR:NO REPLY
28109 TSM:FPAR
29709 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
31716 !TSM:FPAR:NO REPLY
31718 TSM:FPAR
33317 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
35325 !TSM:FPAR:NO REPLY
35328 TSM:FPAR
36927 TSF:MSG:SEND,1-1-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
38935 !TSM:FPAR:FAILAnd keeps on going to
161233 TSM:FAIL:CNT=7
161235 TSM:FAIL:DIS
161238 TSF:TDI:TSL**This is what i'm reading through SSH...
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connected to 192.168.1.112
mysgw: GWT:RMQ:MQTT CONNECTED
mysgw: GWT:TPS:TOPIC=mysensors-out/0/255/0/0/18,MSG SENT
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7And keeps on going and going and going.
Any ideas why it's not relaying information from the Gateway to the Sensor?
-
could be fake clones of NRF24 radio modules
-
Right again! I got some other brands of radio modules that came today and tried them and they worked like a charm right away. Guess I won’t be buying the ones from makerfire on amazon again. The kuman worked so far and came in anti static bags. The other ones were just loose wrapped in plastic bubble wrap. I feel so stupid posting such an easy fix
-
The first nrf24 I bought were the ones with blob on the pcb, I spent countless hours trying to understand why it wasn't working, then I figured that those were everything but nrf24 so returned them to Amazon and bought other fake clones that were working up to 6/7 meters and I got them refunded after 1 star review I made. Finally I got the good ones (more expensive of course), link in the shopping section of mysensors site.
-
The Ebyte nRF24L01+ Ones?
Also, does MySensors get a commission off of the links provided in the store? I would much rather support you guys!
-
Yes, those.
-
Also, does MySensors get a commission off of the links provided in the store? I would much rather support you guys!
Yes, MySensors does get a commission when using the links in the store (and most links in the forum).
Some more info: https://www.mysensors.org/about/mysensors#do-you-make-loads-of-money-on-this
