Backlit Dimmable LED Mirror with Motion Sensor

RJ_Make

@petewill Also what kind of heat are you getting off that FET?

petewill

@ServiceXp thanks! In my setup I'm not getting any noticeable heat on any of my LED projects. I have run it for hours at 100% and it's not even warm to the touch.

BulldogLowell

this is one of those "I want one" projects, yes?

a lot of cool ways to apply this.

Francois

@hek Yes I am using 1.4.1 on both the sensor. This the error I am getting on the sensor node: The sensor was working on a different node it also has cap on VCC and GRD.

sensor started, id=25, parent=0, distance=2
send: 25-25-0-0 s=255,c=0,t=17,pt=0,l=5,st=fail:1.4.1
send: 25-25-0-0 s=255,c=3,t=6,pt=1,l=1,st=fail:0
read: 0-0-25 s=255,c=3,t=6,pt=0,l=1:M
send: 25-25-0-0 s=0,c=0,t=4,pt=0,l=5,st=fail:1.4.1
send: 25-25-0-0 s=1,c=0,t=1,pt=0,l=5,st=fail:1.4.1
send: 25-25-0-0 s=255,c=3,t=11,pt=0,l=10,st=fail:Mirror LED
lost parent
find parent
send: 25-25-255-255 s=255,c=3,t=7,pt=0,l=0,st=bc:
read: 0-0-25 s=255,c=3,t=8,pt=1,l=1:1
new parent=0, d=2

hek

Strange. Looks like distance to gw is 2 but you're actually communicating to it directly.

Francois

@hek this is the sketch from about that that copy and recompile on 1.4.1. I did not used the codebender to compile the sketch.

This is the serial info on the MQTT Gateway:
0;0;3;0;9;read: 25-25-0 s=255,c=0,t=17,pt=0,l=5:1.4.1
0;0;3;0;9;read: 25-25-0 s=255,c=3,t=6,pt=1,l=1:0
0;0;3;0;9;send: 0-0-25-25 s=255,c=3,t=6,pt=0,l=1,st=ok:M
0;0;3;0;9;read: 25-25-0 s=0,c=0,t=4,pt=0,l=5:1.4.1
0;0;3;0;9;read: 25-25-0 s=1,c=0,t=1,pt=0,l=5:1.4.1
0;0;3;0;9;read: 25-25-0 s=255,c=3,t=11,pt=0,l=10:Mirror LED
MyMQTT/25/255/V_SKETCH_NAME
30 27 00 1B 4D 79 4D 51 54 54 2F 32 35 2F 32 35 35 2F 56 5F 53 4B 45 54 43 48 5F 4E 41 4D 45 4D 69 72 72 6F 72 20 4C 45 44
0;0;3;0;9;read: 25-25-255 s=255,c=3,t=7,pt=0,l=0:
0;0;3;0;9;send: 0-0-25-25 s=255,c=3,t=8,pt=1,l=1,st=ok:1
0;0;3;0;9;read: 0-25-25 s=255,c=3,t=8,pt=1,l=1:1
0;0;3;0;9;send: 0-0-25-25 s=255,c=3,t=8,pt=1,l=1,st=ok:1

Francois

Hi I got this sketch to work. There must have being something wrong with MySensor library 1.4.1 once I re-install it and recompile the sketch it is working.

petewill

@Francois Great to hear and thanks for letting us know!

Francois

@petewill I add a light sensor to your sketch and this now slow everything down what will the reason for this be? The motion sensor will not always pickup motion. I have another node with light and motion sensor and that is working right.

Here is the code:

/***
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 * 
 * DESCRIPTION
 * This sketch provides a Dimmable LED Light using PWM and based Henrik Ekblad 
 * <henrik.ekblad@gmail.com> Vera Arduino Sensor project.  
 * Developed by Bruce Lacey, inspired by Hek's MySensor's example sketches.
 * 
 * The circuit uses a MOSFET for Pulse-Wave-Modulation to dim the attached LED or LED strip.  
 * The MOSFET Gate pin is connected to Arduino pin 3 (MIRROR_LED_PIN), the MOSFET Drain pin is connected
 * to the LED negative terminal and the MOSFET Source pin is connected to ground.  
 *
 * This sketch is extensible to support more than one MOSFET/PWM dimmer per circuit.
 *
 * REVISION HISTORY
 * Version 1.0 - February 15, 2014 - Bruce Lacey
 * Version 1.1 - February 4, 2014 - Pete B - added buttons to control on/off and dim level and a motion sensor
 ***/
 
 
#define SN "Mirror LED with PIR and LDR"
#define SV "1.2"
#define NODE_ID 50  //change to a number to assign a specific ID

#include <SPI.h>
#include <MySensor.h>
#include <Bounce2.h>
#include <MySigningNone.h>
#include <MyTransportNRF24.h>
#include <MyHwATMega328.h>

#define MIRROR_LED_CHILD 0    //ID of the LED child
#define MOTION_CHILD 1  //ID of the motion sensor child
#define CHILD_ID_LIGHT 2 //ID for LDR sensor

#define LIGHT_SENSOR_ANALOG_PIN 0

// NRFRF24L01 radio driver (set low transmit power by default) 
MyTransportNRF24 radio(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);  

#define MIRROR_LED_PIN 3      // Arduino pin attached to MOSFET Gate pin
#define UP_BUTTON_PIN 8  // Arduino Digital I/O pin number for the fade up button 
#define DOWN_BUTTON_PIN 7  // Arduino Digital I/O pin number for the fade down button 
#define POWER_BUTTON_PIN 4  // Arduino Digital I/O pin number for the power button 
#define MOTION_PIN  6  // Arduino pin tied to trigger pin on the motion sensor.

#define FADE_DELAY 10  // Delay in ms for each percentage fade up/down (10ms = 1s full-range dim)
#define FADE_PERCENTAGE 10 //The percentage the fade level will be changed when a button is pressed

MyHwATMega328 hw;
// Construct MySensors library
MySensor gw(radio, hw);

//MySensor gw; //Don't need to define pins unless they are changing from the default

static int currentLevel = 0;  // Current dim level...
uint8_t fadeLevel = 0; //used to store the fade level when using the buttons
uint8_t upPreviousValue;
uint8_t downPreviousValue;
uint8_t powerPreviousValue;

Bounce upDebouncer = Bounce();
Bounce downDebouncer = Bounce();
Bounce powerDebouncer = Bounce();

//motion sensor
uint8_t lastMotion = 0;


unsigned long previousMillis = 0; // last time update //see http://stackoverflow.com/questions/10773425/performing-a-function-after-x-time for more details on this
unsigned long motionDelay = 10000; // interval at which to keep motion sensor trippped (milliseconds).  Used to prevent too frequent updates to Vera. 
unsigned long upPreviousMillis = 0;
unsigned long downPreviousMillis = 0; 
unsigned long buttonFadeDelay = 200; 
int lastLightLevel;

boolean metric = true; 

MyMessage motionMsg(MOTION_CHILD, V_TRIPPED);
MyMessage dimmerMsg(MIRROR_LED_CHILD, V_DIMMER);
MyMessage msg(CHILD_ID_LIGHT, V_LIGHT_LEVEL);
//MyMessage lightMsg(LED_CHILD, V_LIGHT);  removed, updating with dimmer values only

/***
 * Dimmable LED initialization method
 */
void setup()  
{ 
  Serial.println( SN ); 

  gw.begin( incomingMessage,  NODE_ID);

  // Register the LED Dimmable Light with the gateway
  gw.present(MIRROR_LED_CHILD, S_DIMMER );
  gw.present(MOTION_CHILD, S_MOTION);
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
  
  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo(SN, SV);
  
  metric = gw.getConfig().isMetric;
  
 
   // Setup the button
  pinMode(UP_BUTTON_PIN,INPUT);
  pinMode(DOWN_BUTTON_PIN,INPUT);
  pinMode(POWER_BUTTON_PIN,INPUT);
  
  // Activate internal pull-up
  digitalWrite(UP_BUTTON_PIN,HIGH);
  digitalWrite(DOWN_BUTTON_PIN,HIGH);
  digitalWrite(POWER_BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  upDebouncer.attach(UP_BUTTON_PIN);
  downDebouncer.attach(DOWN_BUTTON_PIN);
  powerDebouncer.attach(POWER_BUTTON_PIN);
  upDebouncer.interval(5);
  downDebouncer.interval(5);
  powerDebouncer.interval(5);
  

}

/***
 *  Dimmable LED main processing loop 
 */
void loop() 
{
  
  
  
  //process the LED commands from gateway
  gw.process();
  
 int lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23; 
 // Serial.println(lightLevel);
  if (lightLevel != lastLightLevel) {
      gw.send(msg.set(lightLevel));
      lastLightLevel = lightLevel;
  }  
 
 
  //motion sensor code
  unsigned long currentMillis = millis();
  
     if(currentMillis - previousMillis > motionDelay){
      uint8_t motionDetect = digitalRead(MOTION_PIN);
  
      if(motionDetect != lastMotion){
//        Serial.print("motionDetect Value: ");
//        Serial.println(motionDetect);
        gw.send(motionMsg.set(motionDetect));  // Send tripped value to gw
        
        if(motionDetect == 1){
          previousMillis = currentMillis;  //"Tripped" delay 
        }
        else{
          previousMillis = currentMillis - motionDelay + 1000; //"Not tripped" delay for 1 second to stop rapid "not tripped" and "tripped" updates to Vera
        }
  
         lastMotion = motionDetect; 
      }    
    }

  
/*
There are 3 buttons attached to the mirror.  One is an on/off button and the other two will fade up/fade down.  
The sensor will remember the last fade state and fade the lights to that level next time they are turned on.

If fade up or fade down button is pressed it should store that value into a variable and when the ON button is pressed
it will fade to that previous value.
 */ 

    upDebouncer.update();
    // Get the update value
    uint8_t upValue = upDebouncer.read();
    
    unsigned long upCurrentMillis = millis();
    
    if(upCurrentMillis - upPreviousMillis > buttonFadeDelay){
      if ((upValue == LOW) && (fadeLevel<100)) { //Because of the internal pullup resistors LOW = button is presssed
      
        fadeLevel += FADE_PERCENTAGE;
        fadeLevel = fadeLevel > 100 ? 100 : fadeLevel;
        fadeToLevel( fadeLevel );
        
      }
      upPreviousMillis = upCurrentMillis;
    }
  
    downDebouncer.update();
    // Get the update value
    uint8_t downValue = downDebouncer.read();
    
    unsigned long downCurrentMillis = millis();
    
    if(downCurrentMillis - downPreviousMillis > buttonFadeDelay){
      if ((downValue == LOW) && (fadeLevel>0)) {
        
        fadeLevel -= FADE_PERCENTAGE;
        fadeLevel = fadeLevel < 0 ? 0 : fadeLevel;
        //powerState = fadeLevel; //Remember fade level for when power button is pressed
        fadeToLevel( fadeLevel );
        
      }
      downPreviousMillis = downCurrentMillis;
    }
      
    powerDebouncer.update();
    // Get the update value
    uint8_t powerValue = powerDebouncer.read();
    
    if(powerValue != powerPreviousValue){
      if (powerValue == LOW) {
      Serial.print("Power Button Pressed. fadeLevel is ");
      Serial.println(fadeLevel);
        if (currentLevel > 0) {
          fadeToLevel( 0 );
        }
        else{
          if (fadeLevel == 0) {
            fadeToLevel(50);
            fadeLevel = 50;
          }
          else{
            fadeToLevel(fadeLevel);
          }
        }
      }
      powerPreviousValue = powerValue;
    }
  
   
}

void incomingMessage(const MyMessage &message) {
  if (message.type == V_LIGHT || message.type == V_DIMMER) {
    
    //  Retrieve the power or dim level from the incoming request message
    int requestedLevel = atoi( message.data );
    
    // Adjust incoming level if this is a V_LIGHT variable update [0 == off, 1 == on]
    requestedLevel *= ( message.type == V_LIGHT ? 100 : 1 );
    
    // Clip incoming level to valid range of 0 to 100
    requestedLevel = requestedLevel > 100 ? 100 : requestedLevel;
    requestedLevel = requestedLevel < 0   ? 0   : requestedLevel;
    
//    Serial.print( "Changing level to " );
//    Serial.print( requestedLevel );
//    Serial.print( ", from " ); 
//    Serial.println( currentLevel );

    fadeToLevel( requestedLevel );
    }
}

/***
 *  This method provides a graceful fade up/down effect
 */
void fadeToLevel( int toLevel ) {

//  Serial.print("toLevel Value: ");
//  Serial.println(toLevel);
//  Serial.print("currentLevel Value: ");
//  Serial.println(currentLevel);
  
  int delta = ( toLevel - currentLevel ) < 0 ? -1 : 1;
  
  while ( currentLevel != toLevel ) {
    currentLevel += delta;
    analogWrite( MIRROR_LED_PIN, (int)(currentLevel / 100. * 255) );
    delay( FADE_DELAY );
  }

   // Inform the gateway of the current DimmableLED's SwitchPower1 and LoadLevelStatus value...
  //gw.send(lightMsg.set(currentLevel > 0 ? 1 : 0));  //used to send status of light (on/off) to Vera
  gw.send( dimmerMsg.set(currentLevel) );
}

petewill

@Francois I usually put a "millis" delay for all of my sensors that don't need instant updates (temperature, humidity, light, etc). I have had some of my sensors updating too frequently and causing communication issues for the rest of my sensors. Maybe that's what's happening to you? Try adding some code so the light sensor only updates once per 10 seconds or what ever interval you feel is good. You can use my motion sensor code as an example for adding a delay with millis.

henno

@petewill Just wanted to let you know that I've built two of these for my daughters but instead of putting them behind a mirror I put it under their bed. Works really good, thanks for sharing!

petewill

@henno Cool idea!

hek

@henno said:

I've built two of these for my daughters but instead of putting them behind a mirror I put it under their bed.

Scares away all the monsters? :trollface:

DrJeff

@henno That is too funny I was at a hotel and they had LEDs under the cabinets with motion sensors to light the floor. So when I came home I knew I saw some guy doing something similar to a mirror that I'm gonna steal for under my bed to walk at night without bumping my toes! Thanks Pete!

csa02221862

For those of us without a central 12v system do you know what the current draw is?

What is your system setup? Thinking of doing the same.

petewill

@csa02221862 Sorry for the delayed reply. Unfortunately I don't remember what the power draw is. I believe it is around 1.5A but can't say for sure.

csa02221862

Thanks. I'm hopeing to do a "ehole house" 12v system also. What is your power source. I've been looking at

http://www.banggood.com/AC110V-220V-To-DC12V-12_5A-150W-Voltage-Transformer-Switch-Power-Supply-For-LED-Strip-p-984967.html?currency=USD&createTmp=1&utm_source=google&utm_medium=shopping&utm_content=saul&utm_campaign=led-gadget-US&gclid=Cj0KEQjw44exBRCu8vfS_bPEtNoBEiQACrt002cdBU-mBxB0Z5PGsGCkTgwp37OcWYL28zNGmJNjTu8aAitZ8P8HAQ

Thoughts?

petewill

@csa02221862 Depending on what you want to run it may be a little under powered. For the last year and a half I have been using a hacked 300 watt PC power supply. I originally just set it up as a temporary measure but it has been working great. I have even made some stupid wiring mistakes and shorted it out a few times. Each time I just fix the mistake and it powers right back on. I need to make a video of how I set everything up but I have had so little time lately...

csa02221862

Thanks for the info. I may get this for use in the "lab" and see what you are doing with the computer power supply when you do the video. I believe many of us would like to have a 12v/5v power distribution system in the house.

Your videos are OUTSTANDING!

csa02221862

Looking forward to the "whole house power" video.

I'm building this for two mirrors as well as kitchen under counter and bookcase down lighting.

Your Vera videos have been MOST helpful. You do great "practical" work.

THANKS AGAIN!

Backlit Dimmable LED Mirror with Motion Sensor

12

11.7k

11.2k

113.0k