Mysensors orange Pi SPI gateway

[Pavel Polititsky]

This post is deleted!

[gohan]

Domoticz has mqtt support for MySensors, but id to make a proper mqtt mysensors gateway just to exclude something wrong in your chain. Do you have any spare esp8266 to use?

[Pavel Polititsky]

@gohan Now Ive changed my hardware to SPI according with this guide
I have connected my NRF24 module (already checked on arduino) through SPI0 iface but something goes wrong again

root@orangepipcplus:/MySensors#  ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0
mysgw: Serial port /dev/ttyUSB020 (115200 baud) created
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,14-14-0,s=0,c=0,t=14,pt=0,l=1,sg=1:
mysgw: !TSF:MSG:LEN,14!=32
mysgw: TSF:MSG:READ,14-14-0,s=0,c=0,t=14,pt=0,l=1,sg=1:
mysgw: !TSF:MSG:LEN,0!=32

NRF24 link looks like working properly but next I see
infinite messages LEN,0! that going very fast

root@orangepipcplus:/MySensors# ./configure --spi-spidev-device=/dev/spidev0.0 --my-transport=nrf24 --my-rf24-ce-pin=6 
--my-rf24-cs-pin=10 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020 --my-rf24-irq-pin=5
[SECTION] Detecting target machine.
  [OK] machine detected: SoC=unknown, Type=unknown, CPU=armv7l.
[SECTION] Checking GPIO Sysfs.
  [OK] /sys/class/gpio/export found
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

Sure I know that GPIO H2 and H3 are different
When I connecting IRQ wire - log has been ended at mysgw: MCO:BGN:INIT OK,TSP=1 and nothing more
I have tried to change CE/CS pins numbers to wrong but log still the same. As if gpio not working

[gohan]

Did you put a capacitor on nrf24 radio? Try the gw without -my-rf24-irq-pin=5
I have no experience on the OrangePi platform, so I can't help much, that is why I was asking for ESP8266

[Pavel Polititsky]

@gohan of course I have capacitor connected 100uF (even 1000uF)
I will try aftermorrow because my esp shield in my office
Anyway its not a solution, only for testing...

Without IRQ I have
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7

[gohan]

100uF is quite big, I bought a bag of 10uF ceramics and they work perfectly.

[Pavel Polititsky]

@gohan 10uF ceramic does not help

[gohan]

I dont' know if it may apply to you but take a look
https://forum.mysensors.org/topic/5174/solved-non-healing-tsm-msg-len-error-hours-into-run