Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

The Repeater Stick

titvs last edited by

My latest "speedy" design: a small case for an Arduino Nano and a NRF24 module used as a Repeater.

Get it at Thingiverse
Reply Quote 3
1 Reply Last reply
alowhum Plugin Developer last edited by

For people without a 3D printer: Aliexpress has some cases that are a perfect fit too, very similar to this shape.

https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20180826132247&SearchText=electronics+case
Reply Quote 0
1 Reply Last reply
titvs last edited by @alowhum

@alowhum Good find!
Reply Quote 0
1 Reply Last reply

3
Posts

1248
Views

Log in to reply

Suggested Topics

Pass reset on forum
General Discussion • • Dvbit

2

0
Votes

2
Posts

956
Views

I believe Henrik fixed this issue today; see - http://forum.mysensors.org/topic/39/forum-registration-confirmation-url-points-to-localhost#226
3d hubs alternative?
Enclosures / 3D Printing • • sundberg84

11

0
Votes

11
Posts

1451
Views

@NeverDie Yeah, but when I priced out domestic places, they all wanted enough that the client just decided to go a different way. This was only going to be for a prototype, but even so, I got prices ranging from I think $10-50 per pin holder, and it was less than 2 grams of plastic each. I just checked again, and JLCPCB would do them for $1 each, and then $20 for quick shipping, and as low as $4 for the slow boat that takes a month. None of those options were very appealing at the time. Digikey wants $13.66 each for this when I pick qty 10, so still not worth it for this project. Shipping with them is free, but I have no idea how quick they would be. I also checked PCBWay, just for fun, and they quoted 1.24 at qty 10, for $12.45 total. Interestingly, the quote for 1 was $12.45 also. They wouldn't show an estimate for shipping without clicking the 'Submit' button and having a human engineer review the file for printability. Since I'm not actually going to do this now, I don't want to waste their time, so I don't have a total price from them for comparison. As far as OP, this is a very old thread from 3.5 years ago, so I doubt that they still need help.
New enclosures
Enclosures / 3D Printing • • AlexNO

7

0
Votes

7
Posts

482
Views

Very nice! I knew it would only be a matter of time until we saw MySensors custom injected molded components! I think if you made a box that could fit the Easy / Newbie board (~50x50cm) plus radio and 2AA batteries, you would probably sell a lot of them! I know I would buy some of those...
Is there a 3D printable enclosure for RPi 4 w/ serial gateway?
Enclosures / 3D Printing • • Kikakee

8

0
Votes

8
Posts

124
Views

@Kikakee
3D printed housing for an MQTT-GW
Enclosures / 3D Printing • • bgunnarb

6

2
Votes

6
Posts

96
Views

@evb Done that. Here is the link
3d printing for accessories designer
Enclosures / 3D Printing • • laurabarreda

3

0
Votes

3
Posts

83
Views

Thanks for sharing!

1
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1