Hi, is there any way to include generic devices in the app imperihome?
I tried to send the information through fake devices such as the voltage of my solar panel by means of light sensor, but I would like to be able to see it on my Multimeter device that works in vera.

I use to ask if you recommend me some app similar to imperihome, I liked autohomationHD but fell in the abandonment (in which all the devices were shown)

Already it resolved, in the end it was my mistake .
had the power connected to the distributor of the lipho battery which has voltage variations (3,4 - 3,9V)

When I connected the VCC and GND to the power outputs of the Arduino mini pro , it works perfectly .

Thank you very much for the help.

By the way, that way I can stabilize the energy that comes from the battery to the dealer to be constant?
With a capacitor?

I get this error in UI7

Arduino:1.6.7 (Windows 7), Placa:"Arduino Nano, ATmega328"

WARNING: Category '' in library UIPEthernet is not valid. Setting to 'Uncategorized'
D:\Users\Colosus\Desktop\ir_prueba\ir_prueba.ino: In function 'void setup()':

ir_prueba:141: error: 'msgIrRecord' was not declared in this scope

gw.send(msgIrRecord.set(0));

       ^

D:\Users\Colosus\Desktop\ir_prueba\ir_prueba.ino: In function 'void loop()':

ir_prueba:168: error: 'msgIrRecord' was not declared in this scope

         gw.send(msgIrRecord.set(0));

                 ^

D:\Users\Colosus\Desktop\ir_prueba\ir_prueba.ino: In function 'void incomingMessage(const MyMessage&)':

ir_prueba:197: error: 'V_IR_RECORD' was not declared in this scope

if (message.type == V_IR_RECORD) { // IR_RECORD V_VAR1

                    ^

'msgIrRecord' was not declared in this scope

I connected the pin to GND and has stopped giving positive for the last 10 hours .
I guess then the sensor will be problem , I would like to not have to put a step up but if there is no choice ...

ok i disconnect the sensor and bridge the signal to arduino with a gnd pin and nothing happens.
but I have observed that even if you remove the all the wires, get random positives

i don´t know how i do wrong X(

Yeah!! is a HC-SR501 I 'm power the system with a lithium battery that gives me a discharge of between 4.10 and 3.8 volts constantly .
The arduino mini pro is at 3.3v

I have observed that even if you remove the power cables leaving only the signal , I get false positives

Will I need put a capacitor at the output of the battery?

Hello, I have a problem with my modification of the PIR sensor to 3.3v , I followed tutorials and have bridged the pin welding H.

Vera works but every so often false positives sends me , I've tried changing the sensitivity does not work , any suggestions?

Works!!! Thanks a lot, i upload my remake of multimeter for UI7, all works but i only use the current and the voltage for my solar module, i will change the impedance to Kw/h

Vera Files:
http://www51.zippyshare.com/v/fk2Ay5ww/file.html

Now i have a problem with the 3.3 PIR mod, i open a new post XD

ok!! Like this?

float VoltBatScale = analogRead(A2);
float VoltLevelBat = VoltBatScale*4.12/376; //376 is the analog read at 4.12v (full charged battery)
if (VoltLevelBat != lastVoltLevelBat) {
gw.send(msgVoltBat.set((float)VoltLevelBat,2),1);
lastVoltLevelBat = VoltLevelBat;