I use https://www.datamobile.ag/ for my hive scales, very good and you pay for what you use.

The radio is only powered by the battery, the battery must be connected to test. Connect both the usb (set to 3.3v) and the battery, no damage will be caused by this.

I use https://www.datamobile.ag/ for my hive scales, very good and you pay for what you use.

The radio is only powered by the battery, the battery must be connected to test. Connect both the usb (set to 3.3v) and the battery, no damage will be caused by this.

/ Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
#define MY_IP_ADDRESS 192,168,1,110

// If using static ip you can define Gateway and Subnet address as well
#define MY_IP_GATEWAY_ADDRESS 192,168,1,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0

change #define MY_IP_GATEWAY_ADDRESS 192,168,1,1

to MY_IP_GATEWAY 192,168,1,110
and see if that works.

did you add a decoupling capacitor to the radio?

@rafael156 said in not working Ethernet Gateway (sensebender and/or nano gateway):

For the W5100 does "MO"=MOSI and "MI"=MISO?

Yes.
I have just built a gateway with funduino w5100, I have it connected over usb (for power) to a RPI for now, it works well.

So i have given up with iobroker and used FHEM instead, worked well first time.

@stephen205

I have looked in the iobroker/mysensors/getmeta.js

line 10 'S_WIND': {index: 9, role: 'direction', vars: ['V_WIND', 'V_GUST']},

Is V_DIRECTION supposed to be included there and could that be the cause of the problem?

Re: [fody weather station](wind sensor)

I found one of these on ebay for €26 and then found this thread
https://forum.mysensors.org/topic/6645/fody-weather-station-wind-sensor
WOW did that just save me loads of time.

At the moment I am happy that everything is working ok with the unit and sending the data to the gateway, But...
I am trying to get the data into iobroker and it all works apart from the wind direction.

iobroker shows the node wind with only V_GUST and V_WIND but not V_DIRECTION

1871203 TSF:MSG:SEND,1-1-0-0,s=200,c=1,t=8,pt=7,l=5,sg=0,ft=0,st=OK:0.3
Wind speed: 0.27
1871212 TSF:MSG:SEND,1-1-0-0,s=200,c=1,t=9,pt=7,l=5,sg=0,ft=0,st=OK:29.7
Wind gust: 29.65
1871221 TSF:MSG:SEND,1-1-0-0,s=200,c=1,t=10,pt=7,l=5,sg=0,ft=0,st=OK:180
Wind direction: 180
1871228 TSF:MSG:READ,0-0-1,s=200,c=1,t=8,pt=7,l=5,sg=0:0.3
1871235 TSF:MSG:ACK
1871237 TSF:MSG:READ,0-0-1,s=200,c=1,t=9,pt=7,l=5,sg=0:29.7
1871242 TSF:MSG:ACK
1871255 TSF:MSG:READ,0-0-1,s=200,c=1,t=10,pt=7,l=5,sg=0:180
1871260 TSF:MSG:ACK

Can anyone point me in the right direction to sort this out?
Thanks in advance

I have tried the iobroker forum without luck.

IObroker or openhab support V_VAR and the original sketch works on both controllers, at least for me it does.

IObroker or openhab will work as a replacement controller for Vera.