Navigation

    • Register
    • Login
    • OpenHardware.io
    • Categories
    • Recent
    • Tags
    • Popular
    1. Home
    2. gfink
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    gfink

    @gfink

    2
    Reputation
    11
    Posts
    365
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online

    gfink Follow

    Best posts made by gfink

    • Arduino & Openhab initial setup guide

      Does anyone have a simple guide for setting up an Ardunio Ethernet gateway in Openhab. I've read lots of pages, youtube videos and there doesn't seem to be a good "How to" from beginning to end. There's lots of pieces but the following links are as close as I've come to finding something useful. Does anyone have any advice/guidance?

      Thanks in Advance, (as I've, as many of you have spent countless hours trying to figure this out, which it's very simple to someone.. 😉

      http://www.instructables.com/id/OpenHAB-on-Raspberry-Pi/
      http://www.makeuseof.com/tag/getting-started-openhab-home-automation-raspberry-pi/

      posted in OpenHAB
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd You're correct again sir. I ran "./configure --my-gateway=ethernet --my-transport=rf24 --my-rf24-irq-pin=15" and then make/install. and it now works. Thanks for all of your time, wisdom, and helping us along this journey.

      posted in Troubleshooting
      gfink
      gfink

    Latest posts made by gfink

    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd You're correct again sir. I ran "./configure --my-gateway=ethernet --my-transport=rf24 --my-rf24-irq-pin=15" and then make/install. and it now works. Thanks for all of your time, wisdom, and helping us along this journey.

      posted in Troubleshooting
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd I guess I was under the impression that the purple labels signified the CE / CSN-CS pins for the nrf. That was a little confusing for a slow learner like myself. 🙂

      posted in Troubleshooting
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd 0_1559221735037_338461b5-ff5c-45a3-a564-6b9478b01eed-image.png
      This image is referencing (SPI0 CS0 = pin 24) and (SPI0 CS1 = pin 26). and below that image on the same URL, references this chart. I'm assuming that this is for the RPI (2-3)'s. So should the pic be updated to reference 22/24 and not 24/26 or the chart? Just asking to try to help others as I'd tripped over this for a short while. 🙂

      Raspberry NRF24L01+ Color
      GND GND Black
      3.3V(*) VCC Red
      22 CE Orange
      24 CSN/CS Yellow
      23 SCK Green
      19 MOSI Blue
      21 MISO Violet
      15(**) IRQ Gray

      posted in Troubleshooting
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd I'm using openhab2.4 on the same pi, I'd initially tried it w/o port 5003, similiar to below to no avail. So am I mistaken to even try to run openhab2, and try to run the mySensor's ethernet gateway on the same pi? I was trying to conserve resources.

      ./configure --my-gateway=ethernet --my-controller-url-address=192.168.10.12 --my-transport=rf24 --my-rf24-irq-pin=15

      posted in Troubleshooting
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      @mfalkvidd Also, fyi, the drawing may need to be updated, as it's referencing pings 24/26 whereas the charts shows 22/24. If I'm reading it correctly: https://www.mysensors.org/build/raspberry

      posted in Troubleshooting
      gfink
      gfink
    • RE: Problems with the Raspberry Pi gateway

      Hey @gohan I'm having a similiar issue, I've pasted my
      ./configure --my-transport=nrf24 --my-gateway=ethernet --my-port=5003 --my-gateway=ethernet --my-controller-ip-address=192.168.10.12 as a single line, then "make", and created the service, but I still get the same that Vladimir was getting.

      May 28 19:17:46 ERROR failed to connect
      May 28 19:17:46 DEBUG GWT:TPS:ETH OK
      May 28 19:17:46 ERROR connect: Connection refused
      May 28 19:17:46 ERROR failed to connect
      May 28 19:17:46 DEBUG GWT:TPS:ETH OK
      May 28 19:17:46 ERROR connect: Connection refused
      May 28 19:17:46 ERROR failed to connect
      May 28 19:17:46 DEBUG GWT:TPS:ETH OK
      May 28 19:17:46 ERROR connect: Connection refused
      ^CMay 28 19:17:46 NOTICE Received SIGINT

      I've tried the Master and development branch, and have triple checked the nrf24 wiring, made sure SPI was enabled on my pi, I'm at a loss of ideas, can anyone offer some suggestions?

      posted in Troubleshooting
      gfink
      gfink