Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

NRF52 MQTT gateway

Omemanti last edited by

Hey all,
I want to upgrade my system to be able to use MQTT.

ATM, I'm using a ESP8266 (ESP-link) with an Ebyte NRF52832 as a mysensors gateway (LINK)

Can anyone point me on how to achieve this.
So my goal is:
Let all my NRF52832 mysensor nodes report to an MQTT broker (preferably bound to an ESP8266)

Who can point me in the right direction, or even better, tell me how to achieve this.
Reply Quote 0
1 Reply Last reply

1
Posts

26
Views

Suggested Topics

Welcome
Announcements • • hek

8

0
Votes

8
Posts

3221
Views

@NotYetRated Hope you'll find good uses and a fun time while building your sensors.
Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

2

2
Votes

2
Posts

35
Views

@Kokosnoot good solution. I remember the discussion in the early days of MySensors. I've powered the radio's for most of my sensors from the 3.3v regulator on the arduino board and for me that works perfect. But for my latest designs I decided to add a separate ams regulator for my radio's like the guys suggested in the beginning. Because you basically want the on board regulator to power the mcu only.
nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

44

18
Votes

44
Posts

8024
Views

The output of the display could also be sent over serial, but the whole idea is you can walk around with the doctor and improve your results as you go.
Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

90

7
Votes

90
Posts

73900
Views

Hello everyone, Firstly, I apologize for reviving such an old thread, but I find myself in a unique situation and was hoping some of you might be able to help. I hope everyone's doing well. I have a specific inquiry that I couldn't find a recent solution for. Does anyone here know of a tool to generate "fake" Dooya remote (DC90) RF codes for curtains? I've acquired a few motors without controllers and am trying to integrate them with Home Assistant and Bradlink RF remote. Specifically, I'm searching for a way to generate codes for the Up, Down, Stop, and the "Set" button functions to configure curtain limits. Any insights or guidance would be immensely appreciated. Thank you so much in advance!
Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

1

2
Votes

1
Posts

22
Views

No one has replied
A low cost energy meter
My Project • • OldSurferDude

7

1
Votes

7
Posts

44
Views

@OldSurferDude yes, you are correct. this sensor is capable of 50A continuous, which safely I would make it working at 40A max., but for such an important load as in your case I would go for a beefier one, like the ACS75x, 77x, but at this point I would also change the node's form factor for space and insulation reasons. On my application on the RV I have a max. curr. of 13A running on a AWG14-16 cable (European rules for RVs), so I did not ask myself too many questions beside, of course, safety. About the signal, it will be a sinusoidal signal swinging around Vcc/2. Vcc can be easily measured internally on the ATmega328. On all my DC sensors I measure Vcc at every loop, just before measuring the ADCs. Honestly, when the space is not an issue like in my RV, I would rather use a ring core current transformer, and I would get rid of noise, response time, power dissipation, but over all no need to cut any cable. Long story short, it has been a nice experiment and I used it for 6 months, and then I switched back to my RF-NANO based RS485-Modbus - Mysensors bridge connected to an off-the shelf power analyzer. Just for fun I attach a pic of my 12Vdc sensors installed on my RV. Forgive me for the spaghetti wiring on the right side, but this is an area that needs improvement.

NRF52 MQTT gateway

Suggested Topics

Welcome
Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

A low cost energy meter
My Project • • OldSurferDude

44
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

NRF52 MQTT gateway

Suggested Topics

Welcome Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement) My Project • • Kokosnoot

nRF24Doctor My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home My Project • • fsgraz

A low cost energy meter My Project • • OldSurferDude

44Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Powering ESP8266 / NRF24L01 repeater through USB (improvement)
My Project • • Kokosnoot

nRF24Doctor
My Project • power consumption diagnose transmission delays compare modules radio quality doctor range gateway location nrf24 radio • • Technovation

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

Auxiliary Loads and Mains Charger Controller for my Smart Mobile Home
My Project • • fsgraz

A low cost energy meter
My Project • • OldSurferDude

44
Online

11.4k
Users

11.1k
Topics

112.7k
Posts