Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Inverse gateway leds behavior

John Plugin Developer last edited by

Is it possible to switch the LED blink modes So that they are off and blink on message/error or should i inverse this with hardware?
Reply Quote 0
2 Replies Last reply
hek Admin last edited by @John

This post is deleted!
Reply Quote 0
1 Reply Last reply
Damme Code Contributor last edited by @John

@John My guess whould be to pull the led to VCC instead of GND..
Reply Quote 0
1 Reply Last reply
John Plugin Developer last edited by John @Damme

@hek
[original_post_deleted]

@Damme
Yeah, i think i will go for an HW solution... Maybe with a switch to choose between modes...
Reply Quote 0
1 Reply Last reply

4
Posts

1529
Views

Log in to reply

Suggested Topics

ESP8266 Gateway
Troubleshooting • gateway esp8266 nrf24l01+ gateway • • sash.sc

2

0
Votes

2
Posts

56
Views

@sash-sc upgrade MySensors to 2.3.2 or downgrade the esp board definition. More info: https://github.com/mysensors/MySensors/releases/tag/2.3.2
Multiple virtual nodes on a gateway
Troubleshooting • gateway serial gateway temperature & humidity sensor node id • • pvoj

10

0
Votes

10
Posts

1047
Views

@nca78 about my gateways: an old gateway running on MySensors 1.5 for years now. There are several nodes and sensors connected through it like temperature sensors, relays, switches. It controls my heating system with heat pump, buffering, 18 circles of floor heating, garden irrigation, alarm system, and some lights just for fun. the new gateway is a gateway to a Bluetooth network. Since MySensors has a great serial API and I have some experience with it I preferred to use it without a radio. I also think that it will be an interesting way of development and it could help to make MySensors even more popular. I had an idea to fork the library but unfortunately I don't have the experience and time to make it in good quality. But I'm sure letting developers to build connectors to different protocols is a very good idea. Catching Bluetooth messages from the air and decode them (with some reverse engineering) to send it through the MySensors gateway is relatively simple compared to the bidirectional communications. Processing some simple sensor data is a good first step.
all the gear, no idea
General Discussion • gateway vera help newbie • • baldsi

10

0
Votes

10
Posts

4663
Views

@maltimus - thanks, I can see the picture. frstratingly I have the Vera Edge though!
Ethernet gateway troubleshooting advice
Troubleshooting • gateway nrf24l01+ vera ethernet w5100 • • jkbrowne

69

0
Votes

69
Posts

38807
Views

Sorry for the huge kick.. But I seem to have the same ethernet gateway as TS. His his wire diagram valid?
W5100 Ethernet Gateway in Release 2.5.0-1
Troubleshooting • gateway • • chrkir

1

0
Votes

1
Posts

22
Views

No one has replied
💬 RS485 Ethernet Gateway
OpenHardware.io • gateway ethernet rs485 mysensors gateway sensor network • • openhardware.io

5

0
Votes

5
Posts

1087
Views

@kimot No, it is an obvious mistake, I am very sorry. Maybe it is becouse the code in master branch is very old, the newest is not yet on github, but the developement branch is quite new. I am going to fix this soon.
Future network topology (for discussion)
Hardware • gateway network • • axillent

13

2
Votes

13
Posts

6999
Views

Network topology is the bargain of the assorted rudiments (links, nodes) of a computer network. Fundamentally, it is the topological arrangement of a complex & may represent actually or reasonably. link text
Just starting out have a question
General Discussion • gateway newbie • • Chaotic

5

0
Votes

5
Posts

2472
Views

slight bump to this topic rather than starting a new one since I have some more questions Are there any example sketches for setting variables on a node? Thinking I'd want at least 2 variables. Is there a proper way for a node to report time to the controller or other nodes? This one will be powered 100% of the time so responding to messages shouldn't be a problem. I'm pretty sure I know the answer to this one but best way to set up a sketch to report the temp every X when it isn't the main function of the node. Thanks in advance.

27
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1