Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Inverse gateway leds behavior

John Plugin Developer last edited by

Is it possible to switch the LED blink modes So that they are off and blink on message/error or should i inverse this with hardware?
Reply Quote 0
2 Replies Last reply
hek Admin last edited by @John

This post is deleted!
Reply Quote 0
1 Reply Last reply
Damme Code Contributor last edited by @John

@John My guess whould be to pull the led to VCC instead of GND..
Reply Quote 0
1 Reply Last reply
John Plugin Developer last edited by John @Damme

@hek
[original_post_deleted]

@Damme
Yeah, i think i will go for an HW solution... Maybe with a switch to choose between modes...
Reply Quote 0
1 Reply Last reply

4
Posts

1528
Views

Log in to reply

Suggested Topics

Ethernet Gateway Library
My Project • gateway • • Rez

6

0
Votes

6
Posts

51
Views

thanks Mr @mfalkvidd .
st=fail on gateway
Troubleshooting • gateway ethernet w5100 wiznet wiz5100 • • cayco

3

0
Votes

3
Posts

2908
Views

RTF(T)roubleshoot-guide http://www.mysensors.org/build/debug
MQTT Gateway + wi-fi instead of ethernet
Controllers • gateway mqtt wi-fi • • vladimir

4

0
Votes

4
Posts

2949
Views

Although it should not be too difficult to make the MQTT Gateway with WiFi work on hardware and software level it is a bad idea on system level: WiFi and MySensensor NRF24L01+ use the same 2.4 GHz band and with the antennas close a transmit from one will block the other and vice-versa.
💬 Just RFM gateway
OpenHardware.io • mysensors gateway rfm69 contest2017 atsha204a usb • • openhardware.io

19

1
Votes

19
Posts

5113
Views

@Koresh I do like it, i just worry for people that use their main PC as a controller. Easily knockable/damageable unless they use a rear socket.
RFM69HW antenna
General Discussion • gateway pcb rfm69hw antenna • • tsunami

10

0
Votes

10
Posts

1020
Views

@tsunami My setup is max 50m radius and 433MHz standard power RFM69s so a small 1/4 wave whip works reliably even from a below ground pump chamber 10m away. Your 915MHz at 200m SHOULD work on 1/4 wave if obstacle free line of sight, but you could try a 2.4GHz Wifi router at one location and use a mobile at the other to test if you can see the router. I can see at least 3 neighbouring routers identified on my mobile from over 40m away through masonry, 10 on the laptop, so it's a simple enough test. If you can see the router on either, 915MHz should be rock solid with a simple whip and no need of directional antenna.
Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
💬 MyGateway
OpenHardware.io • mysensors gateway rfm69 ethernet poe • • openhardware.io

6

0
Votes

6
Posts

137
Views

@hlehoux glad to hear that!!
Have anyone experienced MySensors gateway with GPRS(MQTT)?
General Discussion • gateway gsm gprs tinygsm sim800l • • jkandasa

2

0
Votes

2
Posts

1330
Views

@jkandasa I just finished a Gateway build with TinyGSM. You can find it here: https://www.openhardware.io/view/567/MySensors-GSM-Gateway

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Copyright 2019 Sensnology | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1