Newbie starting his HA project

[HenryWhite]

@rsachoc Well, you could

• buy an FTDI adapter with jumper

• buy a thinner soldering tip if yours is to big (make sure the tips fit to your soldering iron)

• try to desolder the bridge and solder it to the right place

• break the bridge with pliers and just solder the lower two solder points together. this would be possible even with a thicker soldering iron.

If you want to switch continously between 5v and 3.3v, you should consider buying another ftdi adapter with jumper pins (or try to solder 3 pinheaders to the three solder pads)

[rsachoc]

@HenryWhite thanks! I suspect since I've got nothing to lose the best option is to try and desolder/break the current bridge and try and resolder it. Let me have a go and see what happens.

[rsachoc]

OK so I managed to desolder the bridge and put a dab of solder between the other 2 pins, so I think I have a 3.3v FTDI adaptor. However, I was reading here and I think, because I have the NRF2401 connected to my sensebender, that I might have fried it? Thinking 5v would have broken it?

Also, I'm still confused as to how I connect the FTDI adaptor to the sensebender. mfalkvidd mentioned that I need to go "Vcc to Vcc, GND to GND, RxD to TxD and TxD to RxD", howeverthe sensbender pins don't seem to line up this way?

edit just to be clear, the sensebender goes GND GND VCC RXD TXD DTR while the FTDI goes GND DTR RXI TXO PWR CTS GND, so I'm confused how the pins line up, if that makes any sense?

[mfalkvidd]

sensebender:
GND
GND
VCC
RXD
TXD
DTR

FTDI:
GND
DTR
RXI
TXO
PWR
CTS
GND

Turn FTDI upside-down:
GND
CTS
PWR
TXO
RXI
DTR
GND

now line them up:

sensebender. FTDI
GND GND
GND CTS
VCC PWR
RXD TXO
TXD RXI
DTR DTR

[HenryWhite]

@rsachoc said:

I think, because I have the NRF2401 connected to my sensebender, that I might have fried it? Thinking 5v would have broken it?

Maybe! But maybe not. :smile: I'm using a FTDI adapter with jumper for my 3.3v/5v pro mini's, and sometimes I forgot to move the jumper to 3V when connecting my 3V pro mini's. Nevertheless, the nrf24l01 "survived" this stupidness every time.

Also, I'm still confused as to how I connect the FTDI adaptor to the sensebender. mfalkvidd mentioned that I need to go "Vcc to Vcc, GND to GND, RxD to TxD and TxD to RxD", howeverthe sensbender pins don't seem to line up this way?

edit just to be clear, the sensebender goes GND GND VCC RXD TXD DTR while the FTDI goes GND DTR RXI TXO PWR CTS GND, so I'm confused how the pins line up, if that makes any sense?

here's how you connect the sensebender to your ftdi:

--Your_FTDI:Sensebender--
GND:GND
CTS:GND
PWR:VCC
TXO:RXD
RXI:TXD
DTR:DTR

[rsachoc]

Thank you both, I'll get soldering tomorrow - couple more (extremely rookie) questions:

1. Do I need to have the Sensebender connected to battery and the FTDI connected to USB at the time I'm uploading the sketch?
2. When I upload the sketch, do I need to select Board: Sensebender Micro and Programmer: USBAsp?
3. Do I need to "Upload" or "Upload via Programmer"?

[rsachoc]

@rsachoc OK answering my own question :) after a bit of experimentation and research

Do I need to have the Sensebender connected to battery and the FTDI connected to USB at the time I'm uploading the sketch? No
When I upload the sketch, do I need to select Board: Sensebender Micro and Programmer: USBAsp? Yes
Do I need to "Upload" or "Upload via Programmer"? Upload worked for me

[rsachoc]

An answer, but a new question:

I have setup a MQTT gateway (with NRF2401, Arduno nano clone, W5100 ethernet) - using the W5100 MQTT client sketch (from here), changing the necessary. I can see that this successfully boots and connects to my MQTT server (on a Pi 2 with Openhab).

0;255;3;0;9;Starting gateway (RNNGA-, 2.0.0-beta)
0;255;3;0;9;Radio init successful.
0;255;3;0;9;Init complete, id=0, parent=0, distance=0
0;255;3;0;9;Attempting MQTT connection...
0;255;3;0;9;MQTT connected

I've also successfully flashed the Sensebender .ino (from here), only changing the "//#deine MY_NODE_ID 3" to uncomment (and also correcting the spelling error :) )

Interestingly (no idea why) before I had loaded the new sketch on the Sensebender, when powering it on via battery I got the LED coming on, now with the new sketch...nothing. I also can't see it connecting to the gateway (should I see something in the serial monitor on the gateway)?

Or could I have a fried radio?

[korttoma]

@HenryWhite said:

I forgot to move the jumper to 3V when connecting my 3V pro mini's

I have found that I can program the 5V Pro Minis with the FTDI adapter set to 3.3V so I newer change this anymore, no risk of braking something that can not handle 5V.

[rsachoc]

OK, so I had some success with the Sensebender, it works sometimes and not other times. I've tried connected directly to the laptop (via the FTDI, no battery connected) and sometimes it works, other times it doesn't. Would this bad soldering?

Also, what's the minimum requirements from a voltage perspective? I've got 2 eneloops which delivers around 2.73volts, whereas the laptop measures 3.3v (tested with a voltmeter tester).

[mfalkvidd]

Below 2.8V won't work with the Atmega328 unless you reconfigure the fuses