3 in 1 incl battery monitor
-
Hello,
This is the code I use but it's not perfect especially with the battery report.
The principle is as follow when the sensor start:
- node in sleep mode with interrupt enable
- if a move is detected, the detection is reported to the gateway
- the node then go in sleep mode WITHOUT interrupt for 5 minutes
- then the node return to sleep mode with interrupt enable
This is to avoid having many report (and power consumption) to the gateway.
The code (not perfect ! I have to rework on it but it's ok for the moment):
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * */ /**************************************************************************************/ /* Motion sensor. */ /* */ /* Version : 1.1.5 */ /* Date : 30/01/2016 */ /* Modified by : David Carlier */ /**************************************************************************************/ /* --------------- */ /* RST | | A5 */ /* RX | | A4 */ /* TX | ARDUINO | A3 */ /* RFM69 (DIO0) --------- D2 | UNO | A2 */ /* Motion --------- D3 | | A1 */ /* Power --------- D4 | ATMEGA 328p | A0 */ /* +3v --------- VCC | | GND --------- GND */ /* GND --------- GND | 8MHz int. | REF */ /* OSC | | VCC --------- +3v */ /* OSC | | D13 --------- RFM69 (SCK) */ /* D5 | | D12 --------- RFM69 (MISO) */ /* D6 | | D11 --------- RFM69 (MOSI) */ /* D7 | | D10 --------- RFM69 (NSS) */ /* D8 | | D9 */ /* --------------- */ /* */ /* +3v = 2*AA */ /* */ /**************************************************************************************/ #include <SPI.h> #include <MySensor.h> #include <MyTransportRFM69.h> #include <MySigningAtsha204Soft.h> //Constants #define SKETCH_NAME "Motion Sensor" #define SKETCH_VERSION "1.1.5" #define CHILD_ID 0 #define CHILD_ID_VOLTAGE 1 #define DIGITAL_INPUT_SENSOR 3 #define BATTERY_REPORT_CYCLE 4 //Report each hour (4 * 15') //Misc. variables uint8_t switchState = 2; unsigned long SLEEP_TIME = 820000; // Sleep time between reads (in milliseconds) (close to 15') unsigned long SLEEP_TIME2 = 275000; // Sleep time after int. (in milliseconds) (close to 5') uint8_t cycleInProgress = 0; uint8_t firstReportDone = 0; uint8_t firstReportWithZeroDone = 0; //Construct MySensors library MySigningAtsha204Soft signer; MyHwATMega328 hw; MyTransportRFM69 transport; MySensor node(transport, hw, signer); MyMessage msgSwitch(CHILD_ID, V_TRIPPED); MyMessage msgVolt(CHILD_ID_VOLTAGE, V_VOLTAGE); /**************************************************************************************/ /* Initialization */ /**************************************************************************************/ void setup() { //Get time (for setup duration) #ifdef DEBUG unsigned long startTime = millis(); #endif //Start MySensors and send the Sketch Version Information to the Gateway node.begin(); node.sendSketchInfo(SKETCH_NAME, SKETCH_VERSION); //Setup the button pinMode(DIGITAL_INPUT_SENSOR, INPUT); //Register all sensors node.present(CHILD_ID, S_MOTION); node.present(CHILD_ID_VOLTAGE, S_MULTIMETER); //Print setup debug #ifdef DEBUG int duration = millis() - startTime; Serial.print("[Setup duration: "); Serial.print(duration, DEC); Serial.println(" ms]"); #endif } /**************************************************************************************/ /* Main loop */ /**************************************************************************************/ void loop() { //Get time (for a complete loop) #ifdef DEBUG unsigned long startTime = millis(); #endif //Read digital motion value uint8_t value = digitalRead(DIGITAL_INPUT_SENSOR); //Get voltage for battery capacity report (add 0.1v to the read value) float realVoltage = (getVoltage() / 100.0) + 0.1; int batteryPcnt = realVoltage * 100 / 3.0; if (batteryPcnt > 100) {batteryPcnt = 100;} //Check is state change if (value != switchState) { //Report result if not first loop if (firstReportDone != 0) { node.send(msgSwitch.set(value==HIGH ? 1 : 0)); } //Store result switchState = value; } //Report data to the gateway each hour if (cycleInProgress >= BATTERY_REPORT_CYCLE || firstReportDone == 0) { node.send(msgSwitch.set(value==HIGH ? 1 : 0)); node.send(msgVolt.set(realVoltage, 2)); node.sendBatteryLevel(batteryPcnt); cycleInProgress = 0; firstReportDone = 1; } //Change cycle number cycleInProgress++; //Print debug #ifdef DEBUG Serial.print("Value is "); Serial.print(value, 1); Serial.print(" "); Serial.print("Cycle is "); Serial.print(cycleInProgress, 1); Serial.print(" "); Serial.print(realVoltage); Serial.print(" v"); int duration = millis() - startTime; Serial.print(" "); Serial.print("["); Serial.print(duration, DEC); Serial.println(" ms]"); Serial.flush(); #endif //Check if the motion was triggered and if it's not the first report if (switchState == 0 && firstReportWithZeroDone == 1) { //Sleep 5' without interrupt node.sleep(SLEEP_TIME2); } //Check if it's the first loop if (switchState == 0 && firstReportWithZeroDone == 0) { firstReportWithZeroDone = 1; } //Sleep until something happens with the sensor node.sleep(DIGITAL_INPUT_SENSOR-2, CHANGE, SLEEP_TIME); } /**************************************************************************************/ /* Allows to get the real Vcc (return value * 100). */ /**************************************************************************************/ int getVoltage() { const long InternalReferenceVoltage = 1056L; ADMUX = (0<<REFS1) | (1<<REFS0) | (0<<ADLAR) | (1<<MUX3) | (1<<MUX2) | (1<<MUX1) | (0<<MUX0); delay(50); // Let mux settle a little to get a more stable A/D conversion //Start a conversion ADCSRA |= _BV( ADSC ); //Wait for it to complete while (((ADCSRA & (1<<ADSC)) != 0)); //Scale the value int result = (((InternalReferenceVoltage * 1023L) / ADC) + 5L) / 10L; return result; }On one sensor I tweak the PIR (remove regulator and diode) but on a second one, I just plug the 3 v to the H pin (see other topic on the forum).
Working correctly for the moment (one month) but it depends on the presence in the house.
David.
-
@ Carlied,
What code is better that one of you or the one from cosmi gate?
What are the different thing? Is your code check'the battery status?
And i get a error:
no matching function for call to 'MySensor::MySensor(MyTransportRFM69&, MyHwATMega328&, MySigningAtsha204Soft&)' -
The error is because I enable the signing function !
Remove the following line:MySigningAtsha204Soft signer;And replace
MySensor node(transport, hw, signer);by
MySensor node(transport, hw);I don't know who had the best sketch.
I measure internal battery status using the 1.1 reference.David.
-
@the-cosmic-gate Nothing special. I made a big sketch, which contains 7-8 sensors (DHT, Si7021, MQ-2/9, PIR, Door magnet, Light, battery) reading code because I would like to upload the same sketch to all nodes and configurate it on controller side, which sensors is on the node and need to read.
But currently I reached the limit with I2C includes, so I need to think over this solution.@icebob said:
@the-cosmic-gate Nothing special. I made a big sketch, which contains 7-8 sensors (DHT, Si7021, MQ-2/9, PIR, Door magnet, Light, battery) reading code because I would like to upload the same sketch to all nodes and configurate it on controller side, which sensors is on the node and need to read.
But currently I reached the limit with I2C includes, so I need to think over this solution.Dear..
Did you finish your big code.... -
Hello,
9v means that you are using a voltage regulator which probably consumes a lot of power.
Why not using AA or AAA battery directly connected to Vcc ?David
@carlierd said:
Hello,
9v means that you are using a voltage regulator which probably consumes a lot of power.
Why not using AA or AAA battery directly connected to Vcc ?David
Motion and DHT needed 5volt i wash thinking..?
So 9 @ the vcc should be strong enough i was thinking.
And i do have @ the same time 3.5 for the radioAre the extern step up better than the step down on a nano?
-
The motion can be adapt to run on 3v easily (connect the Vcc to the H pad if available. You can find information on the forum). The DHT could also run on 3v. I have several nodes like that. No problem.
Can't reply for the step-up because I don't use it.David.
-
The motion can be adapt to run on 3v easily (connect the Vcc to the H pad if available. You can find information on the forum). The DHT could also run on 3v. I have several nodes like that. No problem.
Can't reply for the step-up because I don't use it.David.
@carlierd said:
The motion can be adapt to run on 3v easily (connect the Vcc to the H pad if available. You can find information on the forum). The DHT could also run on 3v. I have several nodes like that. No problem.
Can't reply for the step-up because I don't use it.David.
@ David
How long is the 3v battery running whit this option?
-
i'am back in business after the "big move" and going to try again to get this 4:1 sensor working for a long time uning 2 x AA batteries.
If someone has some new input, please let me know :) and feel free to change the sketch -
i'am back in business after the "big move" and going to try again to get this 4:1 sensor working for a long time uning 2 x AA batteries.
If someone has some new input, please let me know :) and feel free to change the sketch@the-cosmic-gate
Hello,
Motion nodes are still working correctly. The oldest node started the 4 of February is still at 3,29v. My other nodes (temp / humidity / light) are also working correctly but I will replace DHT22 for another sensor.David.
-
Hey @carlierd Just curious if you are still using a DHT22 with your sketch? Have you modified the code much from the above? I am looking at implementing something similiar ( identical actually ) and was wondering if much has changed for you over the last few months?
Thanks!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login