Mysensors Ethernet GW w5100 problem

[mrc-core]

@Anticimex so i have to get my old code and remake it with the code from sensors 2.0.0

[Anticimex]

@mrc-core Examples have moved to a different repo: https://github.com/mysensors/MySensorsArduinoExamples

[mrc-core]

@Anticimex Thanks going to see yhe examples and tried to fix this problem.

[mrc-core]

I'm getting this error on IDE

:\Users\marco\Documents\Arduino\libraries\MySensors/MySensors.h:233:5: error: #error UDP mode is not available for ENC28J60

#error UDP mode is not available for ENC28J60

[Yveaux]

@mrc-core I think the error is quite clear : you enabled UDP which is not supported in combination with ENC

[mfalkvidd]

@mrc-core I found this comment in an old version of the code:

 #undef MY_USE_UDP // Will not fit (or compile) on ENC28J60

So it seems the problem is what the message says, UDP doesn't work on ENC28J60.
@hek might know more

[hek]

Yeah, had to reduce the ENC lib to a minimum to make it compile with MySensors. But it was a couple of years ago. Haven't got the bandwidth to test it now.

[mrc-core]

How did tlpeter got it to work ?
What can i do? Go back to the w5100? At this moment i dont have nothing working at home.

[mrc-core]

@tlpeter can you upload your working sketch

[tlpeter]

Sure i can:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 * Contribution by a-lurker and Anticimex,
 * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
 * Contribution by Tomas Hozza <thozza@gmail.com>
 *
 *
 * DESCRIPTION
 * The EthernetGateway sends data received from sensors to the ethernet link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 *
 * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
 *
 * LED purposes:
 * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
 *
 */

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

// When ENC28J60 is connected we have to move CE/CSN pins for NRF radio
#define MY_RF24_CE_PIN 5
#define MY_RF24_CS_PIN 6

// Enable gateway ethernet module type 
#define MY_GATEWAY_ENC28J60

// Gateway IP address
#define MY_IP_ADDRESS 10,0,0,25  

// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003   

// Controller ip address. Enables client mode (default is "server" mode). 
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. 
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN  3 

#define MY_DEFAULT_ERR_LED_PIN 7  // Error led pin
#define MY_DEFAULT_RX_LED_PIN  8  // Receive led pin
#define MY_DEFAULT_TX_LED_PIN  9  // the PCB, on board LED

#include <SPI.h>
#include <UIPEthernet.h>
#include <MySensors.h>

void presentation()
{
  // Send the sketch version information to the gateway and Controller

  sendSketchInfo("Ethernet GW", "1,0");
}
void setup()
{
}

void loop() {
}

[mrc-core]

Got a problem....

In file included from C:\Users\marco\Documents\Arduino\gw\gw.ino:93:0:

C:\Users\marco\Documents\Arduino\libraries\MySensors/MySensors.h:233:5: error: #error UDP mode is not available for ENC28J60

#error UDP mode is not available for ENC28J60

 ^

Using library SPI at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI
Using library UIPEthernet at version 1.04 in folder: C:\Users\marco\Documents\Arduino\libraries\UIPEthernet
Using library MySensors at version 2.0.0 in folder: C:\Users\marco\Documents\Arduino\libraries\MySensors
exit status 1
Error compiling for board Arduino/Genuino Uno.

[mfalkvidd]

I am able to compile tlpeter's sketch without problem:

Sketch uses 28,142 bytes (91%) of program storage space. Maximum is 30,720 bytes.
Global variables use 1,267 bytes (61%) of dynamic memory, leaving 781 bytes for local variables. Maximum is 2,048 bytes.

@mrc-core did you modify tlpeter's sketch in some way?

[mrc-core]

Hummm then the problem can be my libraries

Using library SPI at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI
Using library UIPEthernet at version 1.04 in folder: C:\Users\marco\Documents\Arduino\libraries\UIPEthernet
Using library MySensors at version 2.0.0 in folder: C:\Users\marco\Documents\Arduino\libraries\MySensors

exit status 1
Error compiling for board Arduino/Genuino Uno.

SPI librarie or UIPEthernet ??? has they aren't version 2.0.0

[tlpeter]

@mrc-core said:

C:\Users\marco\Documents\Arduino\libraries\MySensors

Did you put the sketch in this folder?

[mfalkvidd]

@mrc-core I have the same versions:

Using library SPI at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI 
Using library UIPEthernet at version 1.04 in folder: C:\Users\mfalkvidd\Documents\Arduino\libraries\UIPEthernet 
Using library MySensors at version 2.0.0 in folder: C:\Users\mfalkvidd\Documents\Arduino\libraries\MySensors 

[mrc-core]

@tlpeter Yes i did, an d i have also put it on the test folder but i'm getting always the same error

[mrc-core]

@mfalkvidd i don't understant this exit status 1 has i can see everithing is correct why do i get this error...

[mfalkvidd]

@mrc-core somewhere, MY_USE_UDP is defined. Since UDP is not supported on ENC28J60, the code can not be compiled.

[mrc-core]

The error arduin IDE gives points to this line off code int Mysensors.h

#elif defined(MY_GATEWAY_ENC28J60)
		// GATEWAY - ENC28J60
		#if defined(MY_USE_UDP)
			#error UDP mode is not available for ENC28J60
		#endif

Ok going to see if i can found were the UDP is define. Thanks for the help.

[mfalkvidd]

@mrc-core try adding

#define MY_USE_UDP

at the end of your sketch. You should then get an error saying it is being defined twice. The error message should also say which file and line it was defined on.