Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors MiLight integration

CrankyCoder last edited by

Hey Guys,
Figured I would try to start a new thread for this. Last week I posted the code so far as I have for the milight integration in to 2.0 here.

https://github.com/brunkj/MySensorsMiLight

I have not been able to work on it since. If anyone wants to take a crack at it and has some milights, feel free

I think this could be a very cheap way to replace hue and the $$ that goes with it.

My uploaded code as of now will allow you to pair with your bulb, you have to send the "ON" command with in something like 3 seconds of turning on your light. That's how it pairs. Once you pair, you can send on and off. There is code there from previous versions for some of the other stuff like color change and dim. But I have not figured that part out as far as how I need to send the data.

If @ted is still around he may be able to help even more so since he wrote the original. Im just hack jobbing his code up to 2.0 lol
Reply Quote 3
1 Reply Last reply

1
Posts

1064
Views

Suggested Topics

Over the air updates
General Discussion • • ToSa

87

1
Votes

87
Posts

50410
Views

I would really like to get OTA working here as it's freezing outside and I have to go there to update the software in the greenhouse control system. So please, can we have a 'how to' step-by-step guide to OTA? Please? S.
New user has questions
Hardware • • Doggie

7

0
Votes

7
Posts

50
Views

I am new in this forum and I have a question regarding mysensors and iobroker. I did not work with mysensors up to now. Since some weeks I use iobroker installed on a raspberrypi. Now I want to integrate my 433 Mhz doorbell in iobroker. I know, that there is an adapter for mysensors in iobroker. My question is: Is it possible to get a notification in iobroker if someone is pressing the button on my doorbell? As I understood, I have to connect the receiver to an arduino nano and connect the arduino to my rasberrypi on which iobroker is running.
"Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design"
Hardware • • wrendral

10

0
Votes

10
Posts

42
Views

@wrendral said in "Remote Irrigation with LoRaWAN: LM27313 Challenges and PCB Design": I will go with a Li-Po Battery type: 304048 3.7V 1200mAh Might work, but maybe the internal protection will trigger with the high current peaks. I'd suggest you plan a 0 Ohm, (2512/THT) resistor as R2 and then replace it with a 100Ohm/1Watt if the protection triggers.
Best VOC sensor for detecting a wide range of VOC's?
Hardware • • NeverDie

3

1
Votes

3
Posts

30
Views

@eiten I haven't yet made any progress on finding a good VOC sensor, but along the way I did find out something interesting regarding CO2: namely, if you sleep with your bedroom door closed at night, then the odds are good that the CO2 levels rise to surprisingly high and unhealthy levels. The better CO2 sensors are factory calibrated and never again need recalibration for the life of the sensor (usually around 10 years or so), because they are used in HVAC systems to control fresh air intake to guarantee indoor air quality. As a for instance, here is one such CO2 sensor: https://www.digikey.com/en/products/detail/senseair/006-0-0008/15790694 At around $50 for just the sensor element itself, it's not exactly cheap, but then again, I'd say it's worth it, because who wants to be burdened by remembering to calibrate their CO2 sensors? Ideally, I'd like to find a sensitive VOC sensor that also will never require calibration. Nearly all, and maybe all, of the off-the-shelf IAQ montoring stuff that you might buy for, say, $300 or less seems to require periodic calibration. For that reason, this might be one of those occasions where build is rather than buy.
Sleep mode for bmp280
Hardware • • fishermans

7

4
Votes

7
Posts

3281
Views

Just wanted to say thanks for this, it is still relevant and useful six years later !
Does MySensors require Arduino Timer 2?
Hardware • mysensors interrupt nano interrupts esp • • OldSurferDude

2

0
Votes

2
Posts

21
Views

I have success! (oops, that's suppose to be Timer1) I only sample for 1/60 of a second. What I did was to back up all the timer registered I used and then resorted them after I was done sampling. (As opposed to initializing the registers in setup and then starting the timer when needed.) Now I have a Nano sampling the data and sending it to a MySensors Gateway on an RPi3B+ which then sends it to an MQTT broker runing on an old laptop. Also running on the laptop is Home Assistant running inside of VirtualBox. If MySensors does use Timer1, it appears that restoring the registers allows it to be shared. //------------------------------------------------------ISR ISR(TIMER1_OVF_vect){ // interrupt service routine for overflow TCNT1 = TimerPreloadValue; // must be first line! starts the timer counting again digitalWrite(TRIGGER_START_SAMPLE_PIN,HIGH); samplesVolts[--sample]=analogRead(VOLTS_IN_PIN); // decrement before capturing samplesCurrent[sample]=analogRead(CURRENT_IN_PIN); digitalWrite(TRIGGER_START_SAMPLE_PIN,LOW); if (!sample){ // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,LOW); // indicate that sampling is complete samplingEnd = micros(); TCCR1B &= 248; // turns off timer } } //------------------------------------------------------sampleOneCycle void sampleOneCycle(){ // back up timer registers uint8_t TCNT1_b = TCNT1; uint8_t TCCR1B_b = TCCR1B; uint8_t TCCR1A_b = TCCR1A; uint8_t TIMSK1_b = TIMSK1; // configure timer which starts the sampling noInterrupts(); // disable all interrupts TCCR1A = 0; TCCR1B = 0; TCNT1 = TimerPreloadValue; // preload timer //TCCR1B |= (1 << CS10)|(1 << CS12); // 1024 prescaler TCCR1B &= 248; // turns off timer? TIMSK1 |= (1 << TOIE1); // enable timer overflow interrupt ISR // demark sampling sample = NUMBER_OF_SAMPLES; // count down to zero digitalWrite(TRIGGER_START_SAMPLE_PERIOD_PIN,HIGH); samplingStart = micros(); TCNT1 = 65535; // first trigger right away! TCCR1B |= 1; // turns on timer interrupts(); // enable all interrupts // wait for sampling to be complete while(digitalRead(TRIGGER_START_SAMPLE_PERIOD_PIN)){}; samplingEnd = micros(); // restore timer registers TCNT1 = TCNT1_b; TCCR1B = TCCR1B_b; TCCR1A = TCCR1A_b; TIMSK1 = TIMSK1_b; }