Irrigation Controller (up to 16 valves with Shift Registers)

[tombstone]

Hi I just order all the parts that was listed. Do I need to read the 230 post or it's ok just watched the video.

[dbemowsk]

@tombstone You shouldn't need to read all the posts. Maybe just search the thread if you run into any snags. What kind of setup are you dropping this into? Do you currently have valves installed? Does your setup have a master valve or pump relay? Is it a standard 24V AC system?

[tombstone]

Ok I read it all. Just want to start with the basic then change to pH reader soil reader water reader rain detector.

[tombstone]

It's really hard to work out what's good post over bad post. Lol

[tombstone]

Its my 1st project and I have learnt alot but have got myself a snag and I am getting this....

Arduino: 1.8.3 (Windows 10), Board: "Arduino Pro or Pro Mini, ATmega328 (5V, 16 MHz)"

C:\Users\HTPC\Documents\Arduino\Irrigation_Controller_1\Irrigation_Controller_1..ino:82:21: fatal error: TimeLib.h: No such file or directory

#include <TimeLib.h>

                 ^

compilation terminated.

exit status 1
Error compiling for board Arduino Pro or Pro Mini.

[gohan]

go to library manager and install Time library

[tombstone]

This post is deleted!

[tombstone]

This post is deleted!

[tombstone]

This post is deleted!

[tombstone]

This post is deleted!

[tombstone]

ok I almost there :-D but my pro mini has just Analog 1 to 3. I say I have to change the coda were abouts...
I also have not setup up my Vera Controller as I see you have to pay...

Is there another one that is eazy as I have try some but can not get it to work. eg HomeGenie is download and on my pc but don't think its not to good. don't know how to find my pro mini. happy to chagaen to someing eazer to get me started thanks guys....

[tombstone]

Domoticz LOOKS :-D GOOD
BUT new to all this :-D

[Black Cat]

If you are looking for Software, try openhab.

You need to buy Vera, but the software is free.

[tombstone]

@Black-Cat thanks 😁

[tombstone]

ok so when adding to Domoticz..
I go to hardware...
I name is..... test...
then choose.. MySensors Gateway with LAN interface....
Data Timeout: .... Disabled.....
Remote Address.... (I have tryed)....

IP Address, Subnet Mask, Default Gateway, Primary DNS, Secondary DNS.

(i try everythinbg I can think of and still not work)

Port: ... 5003
My pro min has the red light on and blink blue occassionally.

what I get from the Domoticz log is

2017-07-30 18:00:00.627 Error: MySensors: Can not connect to: 61.9.211.33:5003
2017-07-30 18:00:00.627 TCP: Connection problem (Unable to connect to specified IP/Port)
2017-07-30 18:00:00.627 TCP: Reconnecting in 30 seconds...
'''

[tbowmo]

@tombstone

What hardware are you using for the gateway? Arduino, Sensebender GW, ESP8266, is it wired or wireless?

Does it get an IP address from your router?

Can you successfully telnet to the above IP address on port 5003? (And what is the output)

Does the gateway send any logs to the serial port? If yes, then post them on the forum.

[tombstone]

@tbowmo
The hardware I'am using for the gateway is the Arduino pro mini and its wireless from the NRF24L01+ 2.4GHz Wireless Transceiver

I don't know if it is getting IP address from my router.

have not use telnet before (I have just youtube it and enabled it... all what i got from youtube was that you can send email lol cool)

Does the gateway send any logs to the serial port? If yes, then post them on the forum. (were do I get them logs the ones from Domoticz and below but not much info to go on)

Thanks :-D

[tbowmo]

@tombstone

How is the promini connected to the device runnning domoticz?

To me it sounds like that you have the promini connected directly to your computer where domoticz is running, then you should add it as a serial gateway, and not ethernet gateway

If you haven't already done this, I suggest that you read about the mysensors network so you have a basic understanding on how mysensors works.

[tombstone]

@tbowmo
I have it runing both ways but with serial gateway there no errors but when going to setup there is no NODES.

2017-07-30 19:20:55.764 TCP: Connection problem (Unable to connect to specified IP/Port)
2017-07-30 19:20:55.766 TCP: Reconnecting in 30 seconds...
2017-07-30 19:21:26.035 TCP: Reconnecting...
2017-07-30 19:21:37.093 MySensors: TCP/IP Worker stopped...
2017-07-30 19:27:03.150 MySensors: Using serial port: COM4

[tombstone]

@tombstone

//#define MY_NODE_ID 1  // Set this to fix your Radio ID or use Auto

IS there someing I have missed with adding NODES???