Radio setup give: "check wires"

[olaeke]

@Squint That seem even more tricky that the have printed + on the chip and then it still is non plus.

I really don't remember now if I run the getstatus() on the sensor node or it was only on the gateway, but it sound strange that you get zeros on all information. The only thing I can think of is either is the radio broken or is there som more #define in the code you have to comment out the get the status info to print correctly.

I will also remember that I had to fix some more issue in the code to get the non plus to work, I think a made a hack in the process method in the MySensor class, and still the acknowledge didn't work. But I'm not totally shure, I have had a lot of problem with my sensors and my Vera Edge.

Yesterday I received my new radios (yes + variant) and my Ethernet shield. I have now replaced my radios, replaced the serial gateway with Ethernet (the serial port is not working on Vera Egde, good work Mi Casa Verde!) replaced all my hacked library code with fresh from MySensors.org and...

NOW IT WORKS!

I will take the old non plus radio and burn them in the garden tomorrow!

FYI as sonicblaze wrote is Alice breaking point to give them bad feedback then they contact you within a week and offer you refund,.

[Squint]

@olaeke It turns out mine were actually + models. I had the sensors wired incorrectly because I had SOFTSPI enabled.. Once I realized the correct pinout ( After about 3 days of trial/error/code-digging ) its now reporting the + as it should and the radios are working as intended.

Thanks!

[MLs]

This post is deleted!

[MLs]

@olaeke

I can not get it to work.

The pins I use on nRF24L01 + / nRF24L01

Arduino NRF24L01 Radio Ethernet module
GND GND
3.3V VCC
13 SCK
12 MISO
11 MOSI
6 CSN
5 CE

And what I get is this

STATUS = 0x00 RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=0 TX_FULL=0
RX_ADDR_P0-1 = 0x0000000000 0x0000000000
RX_ADDR_P2-5 = 0x00 0x00 0x00 0x00
TX_ADDR = 0x0000000000
RX_PW_P0-6 = 0x00 0x00 0x00 0x00 0x00 0x00
EN_AA = 0x00
EN_RXADDR = 0x00
RF_CH = 0x00
RF_SETUP = 0x00
CONFIG = 0x00
DYNPD/FEATURE = 0x00 0x00
Data Rate = 1MBPS
Model = nRF24L01
CRC Length = Disabled
PA Power = PA_MIN

What am I doing wrong?

[axillent]

@MLs what else is connected to arduino?

i had the same result yesterday trying to build ethernet gateway using ENC based shield. I'm faced a conflict between radio and ethernet

[MLs]

@axillent

Four Dallas temp sensor.

But what I am interested in is the model I have (nRF24L01 + / nRF24L01) and not to send / receive data.

[axillent]

@MLs if you have original nordic you will see + for the plus version

[MLs]

@axillent

I bought them through the store available here at Mysensors

[axillent]

@MLs it should be OK
the old version is out of production for years

[MLs]

@axillent

Possible, but now I wanted to read it out of the hardware to be sure.

[axillent]

@MLs said:

Possible, but now I wanted to read it out of the hardware to be sure.

that is easy))) check wires

[MLs]

@axillent

As I wrote earlier, it is linked and I have also measured the cables to minimize errors.

[axillent]

@MLs disconnect all from arduino

connect radio as stated here http://www.mysensors.org/build/connect_radio
get example GetStarted sketch from RF24 library and see the output

it should be OK
otherwise most probably the radio is broken

[hek]

@axillent said:

the old version is out of production for years

But they still seem to pop up. See a bit up in the thread.

[axillent]

@hek you knew from our conversation last night that I also got "check wires" and was ready to think that all my modules are the old ones

but finally my issue has nothing to do with version of the chip. It is exactly "check wires" issue and issue of the conflicts with other staff,
and my modules were purchased about two years ago

is it any confirmed case with the old version?

[hek]

@axillent
Yep, if you look at the pictures above they're missing +

[axillent]

@hek you are right
but it seams that only @sonicblaze is owner of this rare thing

[olaeke]

@axillent And me! I started the thread so I have got 10 of the them, maybe something for the MySensors museum!

[axillent]

@olaeke said:

@axillent And me! I started the thread so I have got 10 of the them, maybe something for the MySensors museum!

hm. are the + is missing on top of the nordic chip?

it can be probably still used for mysensors in case of:

• switching data rate to 1Mbs or 2MBs (old version do not support 250Kbs - default to 1.4)
• comment out "check wires" check inside Mysensors library

[olaeke]

@axillent Yes there is no + on those.
I have tried using them but without success. I couldn't get them to work at all on the gateway but if I replaced the gateway with + variant and non + on the node then it "almost" worked. I couldn't get the "Auto Id" function to work. I think it has something with Ack to do, i will remember that I have read somewhere that the hardware ack is only implemented in the + variant.