About DS18B20 onewire.

flopp

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
 * http://www.mysensors.org/build/temp
 */
 
// Enable and select radio type attached
#define MY_RADIO_NRF24

// Enable debug prints to serial monitor
#define MY_DEBUG

#define MY_NODE_ID 14

#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define ATTACHED_DS18B20 40
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 

byte D[ATTACHED_DS18B20][8] = {
{ 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx
{ 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx
{ 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt
{ 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt
{ 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump
{ 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx
{ 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt
{ 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx
{ 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök 
{ 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp
{ 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut
{ 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt
{ 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12
{ 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan
{ 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen
{ 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El
{ 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere
{ 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten
{ 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport
{ 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet
{ 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60
{ 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V
{ 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30
{ 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan
{ 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp
{ 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum
{ 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe
{ 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten
{ 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere
{ 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe
{ 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom
{ 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas
{ 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum
{ 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo
{ 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum
{ 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm)
{ 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering
{ 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten

};

float lastTemperature[ATTACHED_DS18B20];
// Initialize temperature message
MyMessage msg(0,V_TEMP);
MyMessage heat(0,V_STATUS);

void setup()  
{ 
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("OneWire Temp+Heating LED", "20180709");
  
  // Fetch the number of attached temperature sensors  
  //numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) {   
     present(i, S_HEATER);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<ATTACHED_DS18B20; i++) {

  //Serial.println(sensors.getResolution(D[i]), DEC); 
    // Fetch and round temperature to one decimal
 //   float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.;
      float temperature = sensors.getTempC(D[i]);
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature <= 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }

   for (int i=0; i<5;i++){
    int value = analogRead(i);
    /*Serial.print("Pin");
    Serial.print(i);
    Serial.print("=");
    Serial.println(value);
    */
    int j=i+ATTACHED_DS18B20;
    if (value>150) {
      send(heat.setSensor(j).set(1));
    }
    else {
      send(heat.setSensor(j).set(0));
    }
  }
  
  sleep(SLEEP_TIME);
}

pepson

And you dont use library onewire.h ?

flopp

@pepson said in About DS18B20 onewire.:

And you dont use library onewire.h ?

I think it will be included in DallasTemperature.h.

Doesn’t my sketch work for you?

pepson

@flopp
Probably tommorow I test your sketch and send you an info...

And what you mean in sketch write Heat?

And is any chance to modify this sketch and add value name "Description" to each sensor Dallas to send info to controller like Home Assistant to user can easily identify sensors in controller? What is what....

pepson

@flopp
Hi
Tell me... is any chance to add in sketch position to write description for sensor and to send this description to Home Assistant....? It is ok write in other sketch for relay and it works perfect:
https://github.com/lkankowski/arduino-multi-relay/blob/master/arduino-multi-relay.ino

It show in Home Assisnatn this information in description example: Ł2 - kinkiet [C10]

mfalkvidd

@pepson yes. Just change the present call, just like in your sketch.

Example: change

present(i, S_HEATER);

to

present(i, S_HEATER, "Description goes here");

pepson

@mfalkvidd
OK but also must add defined description to all address. But how add also description?

rejoe2

@pepson said in About DS18B20 onewire.:

@mfalkvidd
OK but also must add defined description to all address. But how add also description?

Don't know, if that really works, because I never tested it since my controller sw supports comments: https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/DallasTemperatureSimple/DallasTemperatureSimple.ino

pepson

@rejoe2
But where in sketch you define address and description ?

rejoe2

@pepson That's not necessary: The sketch reads the bus to get all the necessary info and will just send whatever is found.

If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.

pepson

@rejoe2 said in About DS18B20 onewire.:

If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.

Ok i know how add to present description , but still dont know how add description to each sensors.... as in sketch for relay as i show as example.

rejoe2

@pepson I'd suggest you make a test with the "simple" variant of the sketches. Then we could lateron discuss how to deal with an array containing the hardcoded addresses.
Pls. make also a test with the hardcoded version. Afai remember, it will print the needed array to serial, as long as #define PRINT_ARRAY isn't commented.

pepson

@mfalkvidd Can you help me... or change it ?

pepson

@flopp said in About DS18B20 onewire.:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
 * http://www.mysensors.org/build/temp
 */
 
// Enable and select radio type attached
#define MY_RADIO_NRF24

// Enable debug prints to serial monitor
#define MY_DEBUG

#define MY_NODE_ID 14

#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define ATTACHED_DS18B20 40
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 

byte D[ATTACHED_DS18B20][8] = {
{ 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx
{ 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx
{ 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt
{ 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt
{ 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump
{ 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx
{ 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt
{ 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx
{ 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök 
{ 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp
{ 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut
{ 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt
{ 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12
{ 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan
{ 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen
{ 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El
{ 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere
{ 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten
{ 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport
{ 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet
{ 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60
{ 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V
{ 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30
{ 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan
{ 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp
{ 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum
{ 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe
{ 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten
{ 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere
{ 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe
{ 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom
{ 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas
{ 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum
{ 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo
{ 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum
{ 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm)
{ 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering
{ 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten

};

float lastTemperature[ATTACHED_DS18B20];
// Initialize temperature message
MyMessage msg(0,V_TEMP);
MyMessage heat(0,V_STATUS);

void setup()  
{ 
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("OneWire Temp+Heating LED", "20180709");
  
  // Fetch the number of attached temperature sensors  
  //numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) {   
     present(i, S_HEATER);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<ATTACHED_DS18B20; i++) {

  //Serial.println(sensors.getResolution(D[i]), DEC); 
    // Fetch and round temperature to one decimal
 //   float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.;
      float temperature = sensors.getTempC(D[i]);
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature <= 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }

   for (int i=0; i<5;i++){
    int value = analogRead(i);
    /*Serial.print("Pin");
    Serial.print(i);
    Serial.print("=");
    Serial.println(value);
    */
    int j=i+ATTACHED_DS18B20;
    if (value>150) {
      send(heat.setSensor(j).set(1));
    }
    else {
      send(heat.setSensor(j).set(0));
    }
  }
  
  sleep(SLEEP_TIME);
}

When i try compile this sketch it get me error:

C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':

Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'

sensors.requestTemperatures();

^

exit status 1
expected initializer before 'sensors'

mfalkvidd

@pepson you have a stray } after setWaitForConversion

Tip: use ctrl+t in the editor to easier see this type of mistake

pepson

@mfalkvidd
Still is problem after use CTRL+T

/**
   The MySensors Arduino library handles the wireless radio link and protocol
   between your home built sensors/actuators and HA controller of choice.
   The sensors forms a self healing radio network with optional repeaters. Each
   repeater and gateway builds a routing tables in EEPROM which keeps track of the
   network topology allowing messages to be routed to nodes.

   Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
   Copyright (C) 2013-2015 Sensnology AB
   Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

   Documentation: http://www.mysensors.org
   Support Forum: http://forum.mysensors.org

   This program is free software; you can redistribute it and/or
   modify it under the terms of the GNU General Public License
   version 2 as published by the Free Software Foundation.

 *******************************

   DESCRIPTION

   Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
   http://www.mysensors.org/build/temp
*/

#define MY_GATEWAY_SERIAL

// Enable debug prints to serial monitor
#define MY_DEBUG

#define MY_NODE_ID 14

#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define ATTACHED_DS18B20 40
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature.

byte D[ATTACHED_DS18B20][8] = {
  { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx
  { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx
  { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt
  { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt
  { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump
  { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx
  { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt
  { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx
  { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök
  { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp
  { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut
  { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt
  { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12
  { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan
  { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen
  { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El
  { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere
  { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten
  { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport
  { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet
  { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60
  { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V
  { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30
  { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan
  { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp
  { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum
  { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe
  { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten
  { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere
  { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe
  { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom
  { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas
  { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum
  { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo
  { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum
  { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm)
  { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering
  { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten

};

float lastTemperature[ATTACHED_DS18B20];
// Initialize temperature message
MyMessage msg(0, V_TEMP);
MyMessage heat(0, V_STATUS);

void setup()
{
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("OneWire Temp+Heating LED", "20180709");

  // Fetch the number of attached temperature sensors
  //numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i = 0; i < ATTACHED_DS18B20; i++) {
    present(i, S_TEMP);
  }
  for (int i = ATTACHED_DS18B20; i < ATTACHED_DS18B20 + 5; i++) {
    present(i, S_HEATER);
  }

  void loop()
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller
  for (int i = 0; i < ATTACHED_DS18B20; i++) {

    //Serial.println(sensors.getResolution(D[i]), DEC);
    // Fetch and round temperature to one decimal
    //   float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.;
    float temperature = sensors.getTempC(D[i]);
    // Only send data if temperature has changed and no error
#if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
#else
    if (temperature != -127.00 && temperature <= 85.00) {
#endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature, 1));
      // Save new temperatures for next compare
      lastTemperature[i] = temperature;
    }
  }

  for (int i = 0; i < 5; i++) {
    int value = analogRead(i);
    /*Serial.print("Pin");
      Serial.print(i);
      Serial.print("=");
      Serial.println(value);
    */
    int j = i + ATTACHED_DS18B20;
    if (value > 150) {
      send(heat.setSensor(j).set(1));
    }
    else {
      send(heat.setSensor(j).set(0));
    }
  }

  sleep(SLEEP_TIME);
}

C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':

Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'

sensors.requestTemperatures();

^

exit status 1
expected initializer before 'sensors'

mfalkvidd

@pepson you’re missing a } before start of loop.

pepson

@mfalkvidd
Where ? please show me more.... :( i am beginner

pepson

@pepson ok fixed it :)

pepson

But.... Can you also help me to add to this sketch option to send to example to Home Assistant also DESCRIPTION to each sensors ? And description will be get from sketch from name about address sensor ?

As in this sketch which i have for relay:

#define USE_EXPANDER
// Enable debug prints to serial monitor
//#define MY_DEBUG

#define MY_GATEWAY_SERIAL

#include <MySensors.h>
#include <Bounce2.h>
#ifdef USE_EXPANDER
  #include <Wire.h>    // Required for I2C communication
  #include "PCF8574.h"
  uint8_t expanderAddresses[] = {0x20};
  const int numberOfExpanders = sizeof(expanderAddresses);
  PCF8574 expander[numberOfExpanders];
  #define E(expanderNo, ExpanderPin) (((expanderNo+1)<<8) | (ExpanderPin))
#endif

// No Button Constant
#define NOB -1
#define MULTI_RELAY_VERSION 9
#define RELAY_STATE_STORAGE 1

const uint8_t RELAY_TRIGGER_LOW  = 0;
const uint8_t RELAY_TRIGGER_HIGH = 1;
const uint8_t RELAY_STARTUP_ON   = 2;
const uint8_t RELAY_STARTUP_OFF  = 4;
const uint8_t RELAY_STARTUP_MASK = RELAY_STARTUP_ON | RELAY_STARTUP_OFF;

enum ButtonType {
  MONO_STABLE = 0,
  BI_STABLE = 1,
  DING_DONG = 2 // HIGH state immediatly after push, LOW state after release
};

typedef struct {
  int sensorId;
  int relay;
  int button;
  uint8_t relayOptions;
  ButtonType buttonType;
  const char * relayDescription;
} RelayButton;

// CONFIGURE ONLY THIS ARRAY!
// Row params: sensor ID - sensor ID reported on MySensor Gateway
//             relay pin - Expander supported
//             button pin - <0 for virtual buttons (only available in MySensor Gateway); no support for Expander
//             relay options - [RELAY_TRIGGER_LOW|RELAY_TRIGGER_HIGH] {RELAY_STARTUP_ON|RELAY_STARTUP_OFF}
//             button type - [MONO_STABLE|BI_STABLE|DING_DONG]
//             relay description - reported on MySensor Gateway, can help identify device on initial configuration in Home Automation App, can be empty ("")
RelayButton myRelayButtons[] = {
  {0, 2, A0, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł2 - kinkiet [C10]"},  // WŁ: Ł2
  {1, 16, A1, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 2 [A9]"},  // WŁ: Salon 2
  {2, 15, A2, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 1 [A10]"},  // WŁ: Salon 1
  {3, E(0,1), A3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, BI_STABLE, "Halogen - Taras [B8]"},  // WŁ: Taras
  {4, 22, A4, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia [B2]"},  // WŁ: Kuchnia 1
  {5, 23, A5, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia - Kinkiet [B3]"},  // WŁ: Kuchnia 2
  {6, 28, A6, RELAY_TRIGGER_LOW, BI_STABLE, "Jadalnia 2 [A4]"},  // WŁ: Hall I/Jadalnia prawy
  {17, 17, A7, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Kinkiet [A11]"},  // WŁ: Hall I/Ł1 prawy
  {8, 31, A8, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"},  // WŁ: Kotłownia/Garaż
  {8, 31, A9, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"},  // WŁ: Garaż
  {10, 14, A10, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, BI_STABLE, "Halogen - wejście [B4]"},  // WŁ: Drzwi wejściowe
  {11, E(0,7), A11, RELAY_TRIGGER_LOW, DING_DONG, "Dzwonek [?]"},  // WŁ: Dzwonek
  {12, 29, A12, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Jadalnia lewy
  {12, 29, A13, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Wiatrołap
  {14, 32, A14, RELAY_TRIGGER_LOW, BI_STABLE, "Wiatrołap [A8]"},  // WŁ: Wiatrołap/Hall I
  {15, 19, A15, RELAY_TRIGGER_LOW, MONO_STABLE, "Kotłownia [B1]"},  // WŁ: Kotłownia/Hall I
  {16, 24, 53, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Taśma LED [C1]"},  // WŁ: Hall I/Ł1 środek
  {17, 17, 52, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł1 - Kinkiet [A11]"},  // WŁ: Ł1
  {18, 18, 51, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 [A12]"},  // WŁ: Hall I/Ł1 lewy
  {19, 6, 50, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"},  // WŁ: Hall I/Schody 1
  {12, 29, 49, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Schody 2
  {21, 26, 48, RELAY_TRIGGER_LOW, BI_STABLE, "Gabinet [A2]"},  // WŁ: Gabinet
  {22, 7, 47, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"},  // WŁ: Hall II/Schody 1
  {19, 6, 46, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"},  // WŁ: Hall II/Schody 2
  {24, 10, 45, RELAY_TRIGGER_LOW, BI_STABLE, "Garderoba [C12]"},  // WŁ: Garderoba
  {25, 4, 44, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad kuchnią 2 [B10]"},  // WŁ: Pok. nad kuchnią 2
  {26, 5, 43, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad kuchnią 1 [B9]"},  // WŁ: Pok. nad kuchnią 1
  {27, 8, 42, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad salonem 2 [B12]"},  // WŁ: Pok. nad salonem 2
  {28, 9, 41, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad salonem 1 [B11]"},  // WŁ: Pok. nad salonem 1
  {29, 3, 40, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 [C7]"},  // WŁ: Hall II/Ł2 1
  {30, E(0,3), 39, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 - Taśma LED [?]"},  // WŁ: Hall II/Ł2 2
  {22, 7, 38, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"},  // WŁ: Hall II/Sypialnia
  {32, 11, 37, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 2 [C9]"},  // WŁ: Sypialnia 2
  {33, 12, 36, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 1 [C8]"},  // WŁ: Sypialnia 1
  {34, 25, -1, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, MONO_STABLE, "Halogen - Garaż [A1]"},  // WŁ: Virtual Button 1
  {35, 30, -2, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł1 - Wentylator [A3]"},  // WŁ: Virtual Button 2
  {36, E(0,2), -3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Halogen - wschód [B6]"},  // WŁ: Virtual Button 3
  {37, E(0,4), -4, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki schodowe [C6]"},  // WŁ: Virtual Button 4
  {38, E(0,5), -5, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe I [C4]"},  // WŁ: Virtual Button 5
  {39, E(0,6), -6, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe II [C2]"},  // WŁ: Virtual Button 6
  {40, E(0,0), -7, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł2 - wentylator [C11]"},  // WŁ: Virtual Button 7
};

const int numberOfRelayButtons = sizeof(myRelayButtons) / sizeof(RelayButton);

typedef struct {
  int firstButton;
  int nextButton;
} RelayMultiButtons;

RelayMultiButtons relayMultiButtons[numberOfRelayButtons];
uint8_t myRelayState[numberOfRelayButtons];

// MySensors - Sending Data
// To send data you have to create a MyMessage container to hold the information.
MyMessage msgs[numberOfRelayButtons];

Bounce myButtonDebouncer[numberOfRelayButtons];

//Function Declaration
uint8_t loadRelayState(int relayNum, uint8_t forceEeprom = 0);
void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom);
void saveRelayState(int relayNum, uint8_t state);
void changeRelayState(int relayNum, uint8_t relayState);



// MySensors - This will execute before MySensors starts up
void before() {
  Serial.begin(115200);
  
  #ifdef USE_EXPANDER
    /* Start I2C bus and PCF8574 instance */
    for(int i = 0; i < numberOfExpanders; i++) {
      expander[i].begin(expanderAddresses[i]);
    }
  #endif
  
  // initialize multiple buttons list structure
  for (int i = 0; i < numberOfRelayButtons; i++) {
    relayMultiButtons[i].firstButton = -1;
    relayMultiButtons[i].nextButton = -1;
  }
  // find multiple buttons for the same relay (uni-directional list)
  for (int i = 0; i < numberOfRelayButtons-1; i++) {
    if (relayMultiButtons[i].firstButton == -1) {
      int prevRelayButton = i;
      for (int j = i+1; j < numberOfRelayButtons; j++) {
        if (myRelayButtons[i].relay == myRelayButtons[j].relay) {
          relayMultiButtons[prevRelayButton].firstButton = i;
          relayMultiButtons[prevRelayButton].nextButton = j;
          relayMultiButtons[j].firstButton = i;
          prevRelayButton = j;
        }
      }
    }
  }
  
  // if version has changed, reset state of all relays
  int versionChangeResetState = (MULTI_RELAY_VERSION == loadState(0) ) ? 0 : 1;
  
  for (int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, load only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      // Then set relay pins in output mode
      #ifdef USE_EXPANDER
        if ( myRelayButtons[i].relay & 0xff00 ) {
          // EXPANDER
          int expanderNo = (myRelayButtons[i].relay >> 8) - 1;
          int expanderPin = myRelayButtons[i].relay & 0xff;
          expander[expanderNo].pinMode(expanderPin, OUTPUT);
        } else {
      #endif
          pinMode(myRelayButtons[i].relay, OUTPUT);
      #ifdef USE_EXPANDER
        }
      #endif
      
      uint8_t isTurnedOn = 0;
      
      if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) {
        isTurnedOn = 1;
      } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) {
      } else {
        // Set relay to last known state (using eeprom storage)
        isTurnedOn = loadRelayState(i, 1); // 1 - true, 0 - false
        if (versionChangeResetState && isTurnedOn) {
          saveRelayState(i, 0, 1);
          isTurnedOn = 0;
        }
      }

      changeRelayState(i, isTurnedOn);
      myRelayState[i] = isTurnedOn;
    }
  }
  if (versionChangeResetState) {
    // version has changed, so store new version in eeporom
    saveState(0, MULTI_RELAY_VERSION);
  }
}

// executed AFTER mysensors has been initialised
void setup() {
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0) {
      // No Expander support for buttons (de-bouncing)
      pinMode(myRelayButtons[i].button, INPUT_PULLUP); // HIGH state when button is not pushed
    }
  }
  // Setup locally attached sensors
  delay(5000);
  // Send state to MySensor Gateway
  for(int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, send only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      msgs[i] = MyMessage(myRelayButtons[i].sensorId, V_LIGHT);
      uint8_t relayState;
      if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) {
        relayState = 1;
      } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) {
        relayState = 0;
      } else {
        relayState = loadRelayState(i);
      }
      send(msgs[i].set(relayState)); // send current state
    }
  }
  // Setup buttons
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0) {
      // setup debouncer
      myButtonDebouncer[i] = Bounce();
      myButtonDebouncer[i].attach(myRelayButtons[i].button);
      myButtonDebouncer[i].interval(50);
    }
  }
}

void loop() {
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0 && myButtonDebouncer[i].update()) {
      int buttonState = myButtonDebouncer[i].read();
      #ifdef MY_DEBUG
        Serial.print("# Button ");
        Serial.print(i);
        Serial.print(" changed to: ");
        Serial.println(buttonState);
      #endif
      
      int relayNum = (relayMultiButtons[i].firstButton == -1) ? i : relayMultiButtons[i].firstButton;
      
      if (myRelayButtons[i].buttonType == DING_DONG) {
        if (buttonState == LOW) { // button pressed
          changeRelayState(relayNum, 1);
          send(msgs[relayNum].set(1));
        } else { // button released
          changeRelayState(relayNum, 0);
          send(msgs[relayNum].set(0));
        }
      } else if (myRelayButtons[i].buttonType == BI_STABLE || buttonState == HIGH) {
        // If button type is BI_STABLE, any change will toggle relay state
        // For MONO_STABLE, button must be pushed and released (HIGH)
        uint8_t isTurnedOn = ! loadRelayState(relayNum); // 1 - true, 0 - false
        changeRelayState(relayNum, isTurnedOn);
        send(msgs[relayNum].set(isTurnedOn));
        saveRelayState(relayNum, isTurnedOn);
      }
    }
  }
}



// MySensors - Presentation
// Your sensor must first present itself to the controller.
// The presentation is a hint to allow controller prepare for the sensor data that eventually will come.
// Executed after "before()" and before "setup()" in: _begin (MySensorsCore.cpp) > gatewayTransportInit() > presentNode()
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Multi Relay", "1.2");
  
  // Register every relay as separate sensor
  for (int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, register only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      // Register all sensors to gw (they will be created as child devices)
      // void present(uint8_t childSensorId, uint8_t sensorType, const char *description, bool ack);
      //   childSensorId - The unique child id you want to choose for the sensor connected to this Arduino. Range 0-254.
      //   sensorType - The sensor type you want to create.
      //   description An optional textual description of the attached sensor.
      //   ack - Set this to true if you want destination node to send ack back to this node. Default is not to request any ack.
      present(myRelayButtons[i].sensorId, S_BINARY, myRelayButtons[i].relayDescription);
    }
  }
}


// MySensors - Handling incoming messages
// Nodes that expects incoming data, such as an actuator or repeating nodes,
// must implement the receive() - function to handle the incoming messages.
// Do not sleep a node where you expect incoming data or you will lose messages.
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_STATUS) {
    uint8_t isTurnedOn = message.getBool(); // 1 - true, 0 - false
    changeRelayState(message.sensor, isTurnedOn);
    // Store state in eeprom if changed
    if (loadRelayState(message.sensor) != isTurnedOn) {
      saveRelayState(message.sensor, isTurnedOn);
    }
    send(msgs[message.sensor].set(isTurnedOn)); // support for OPTIMISTIC=FALSE (Home Asistant)
    #ifdef MY_DEBUG
      // Write some debug info
      Serial.print("# Incoming change for sensor: " + message.sensor);
      Serial.println(", New status: " + isTurnedOn);
    #endif
  }
}

uint8_t loadRelayState(int relayNum, uint8_t forceEeprom) {
  uint8_t relayState;
  if (forceEeprom) {
    relayState = loadState(RELAY_STATE_STORAGE + relayNum);
  } else {
    relayState = myRelayState[relayNum];
  }
  #ifdef MY_DEBUG
    Serial.print("# loadRelayState: ");
    Serial.print(relayNum);
    if (forceEeprom) {
      Serial.print("(byte ");
      Serial.print(RELAY_STATE_STORAGE + relayNum);
      Serial.print(")");
    }
    Serial.print(" = ");
    Serial.println(relayState);
  #endif
  return(relayState);
}

void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom) {
  
  int mainRelayNum = (relayMultiButtons[relayNum].firstButton == -1) ? relayNum : relayMultiButtons[relayNum].firstButton;
  
  myRelayState[mainRelayNum] = state;
  if (useEeprom && (relayNum == mainRelayNum)) {
    saveState(RELAY_STATE_STORAGE + mainRelayNum, state);
  }
  
  int nextButton = mainRelayNum;
  // update all buttons
  while ((nextButton = relayMultiButtons[nextButton].nextButton) != -1) {
    myRelayState[nextButton] = state;
  };
}

void saveRelayState(int relayNum, uint8_t state) {
  uint8_t useEeprom = ((myRelayButtons[relayNum].relayOptions & RELAY_STARTUP_MASK) == 0);
  saveRelayState(relayNum, state, useEeprom);
}

void changeRelayState(int relayNum, uint8_t relayState) {
  
  uint8_t relayTrigger = myRelayButtons[relayNum].relayOptions & RELAY_TRIGGER_HIGH;
  uint8_t digitalOutState = relayState ? relayTrigger : ! relayTrigger;
  
  #ifdef USE_EXPANDER
    if ( myRelayButtons[relayNum].relay & 0xff00 ) {
      int expanderNo = (myRelayButtons[relayNum].relay >> 8) - 1;
      int expanderPin = myRelayButtons[relayNum].relay & 0xff;
      expander[expanderNo].digitalWrite(expanderPin, digitalOutState);
    } else {
  #endif
    digitalWrite(myRelayButtons[relayNum].relay, digitalOutState);
  #ifdef USE_EXPANDER
    }
  #endif
}

And in Home assistant show example decription: Ł2 - kinkiet [C10] or for second Salon 2 [A9] etc.
Please help me... because it will be good to identify sensors when add to Controller.

About DS18B20 onewire.

28

11.7k

11.2k

113.1k