About DS18B20 onewire.

pepson

@mfalkvidd
OK but also must add defined description to all address. But how add also description?

rejoe2

@mfalkvidd
OK but also must add defined description to all address. But how add also description?

Don't know, if that really works, because I never tested it since my controller sw supports comments: https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/DallasTemperatureSimple/DallasTemperatureSimple.ino

pepson

@rejoe2
But where in sketch you define address and description ?

rejoe2

@pepson That's not necessary: The sketch reads the bus to get all the necessary info and will just send whatever is found.

If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.

pepson

@rejoe2 said in About DS18B20 onewire.:

If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.

Ok i know how add to present description , but still dont know how add description to each sensors.... as in sketch for relay as i show as example.

rejoe2

@pepson I'd suggest you make a test with the "simple" variant of the sketches. Then we could lateron discuss how to deal with an array containing the hardcoded addresses.
Pls. make also a test with the hardcoded version. Afai remember, it will print the needed array to serial, as long as #define PRINT_ARRAY isn't commented.

pepson

@mfalkvidd Can you help me... or change it ?

pepson

@flopp said in About DS18B20 onewire.:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
 * http://www.mysensors.org/build/temp
 */
 
// Enable and select radio type attached
#define MY_RADIO_NRF24

// Enable debug prints to serial monitor
#define MY_DEBUG

#define MY_NODE_ID 14

#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define ATTACHED_DS18B20 40
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 

byte D[ATTACHED_DS18B20][8] = {
{ 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx
{ 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx
{ 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt
{ 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt
{ 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump
{ 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx
{ 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt
{ 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx
{ 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök 
{ 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp
{ 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut
{ 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt
{ 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12
{ 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan
{ 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen
{ 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El
{ 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere
{ 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten
{ 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport
{ 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet
{ 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60
{ 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V
{ 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30
{ 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan
{ 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp
{ 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum
{ 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe
{ 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten
{ 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere
{ 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe
{ 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom
{ 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas
{ 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum
{ 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo
{ 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum
{ 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm)
{ 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering
{ 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten

};

float lastTemperature[ATTACHED_DS18B20];
// Initialize temperature message
MyMessage msg(0,V_TEMP);
MyMessage heat(0,V_STATUS);

void setup()  
{ 
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("OneWire Temp+Heating LED", "20180709");
  
  // Fetch the number of attached temperature sensors  
  //numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) {   
     present(i, S_HEATER);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<ATTACHED_DS18B20; i++) {

  //Serial.println(sensors.getResolution(D[i]), DEC); 
    // Fetch and round temperature to one decimal
 //   float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.;
      float temperature = sensors.getTempC(D[i]);
    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature <= 85.00) {
    #endif
 
      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }

   for (int i=0; i<5;i++){
    int value = analogRead(i);
    /*Serial.print("Pin");
    Serial.print(i);
    Serial.print("=");
    Serial.println(value);
    */
    int j=i+ATTACHED_DS18B20;
    if (value>150) {
      send(heat.setSensor(j).set(1));
    }
    else {
      send(heat.setSensor(j).set(0));
    }
  }
  
  sleep(SLEEP_TIME);
}

When i try compile this sketch it get me error:

C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':

Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'

sensors.requestTemperatures();

^

exit status 1
expected initializer before 'sensors'

mfalkvidd

@pepson you have a stray } after setWaitForConversion

Tip: use ctrl+t in the editor to easier see this type of mistake

pepson

@mfalkvidd
Still is problem after use CTRL+T

/**
   The MySensors Arduino library handles the wireless radio link and protocol
   between your home built sensors/actuators and HA controller of choice.
   The sensors forms a self healing radio network with optional repeaters. Each
   repeater and gateway builds a routing tables in EEPROM which keeps track of the
   network topology allowing messages to be routed to nodes.

   Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
   Copyright (C) 2013-2015 Sensnology AB
   Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors

   Documentation: http://www.mysensors.org
   Support Forum: http://forum.mysensors.org

   This program is free software; you can redistribute it and/or
   modify it under the terms of the GNU General Public License
   version 2 as published by the Free Software Foundation.

 *******************************

   DESCRIPTION

   Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
   http://www.mysensors.org/build/temp
*/

#define MY_GATEWAY_SERIAL

// Enable debug prints to serial monitor
#define MY_DEBUG

#define MY_NODE_ID 14

#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define ATTACHED_DS18B20 40
unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature.

byte D[ATTACHED_DS18B20][8] = {
  { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx
  { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx
  { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt
  { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt
  { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump
  { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx
  { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt
  { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx
  { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök
  { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp
  { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut
  { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt
  { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12
  { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan
  { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen
  { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El
  { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere
  { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten
  { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport
  { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet
  { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60
  { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V
  { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30
  { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan
  { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp
  { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum
  { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe
  { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten
  { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere
  { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe
  { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom
  { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas
  { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum
  { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo
  { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum
  { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm)
  { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering
  { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten

};

float lastTemperature[ATTACHED_DS18B20];
// Initialize temperature message
MyMessage msg(0, V_TEMP);
MyMessage heat(0, V_STATUS);

void setup()
{
  // Startup up the OneWire library
  sensors.begin();
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("OneWire Temp+Heating LED", "20180709");

  // Fetch the number of attached temperature sensors
  //numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i = 0; i < ATTACHED_DS18B20; i++) {
    present(i, S_TEMP);
  }
  for (int i = ATTACHED_DS18B20; i < ATTACHED_DS18B20 + 5; i++) {
    present(i, S_HEATER);
  }

  void loop()
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller
  for (int i = 0; i < ATTACHED_DS18B20; i++) {

    //Serial.println(sensors.getResolution(D[i]), DEC);
    // Fetch and round temperature to one decimal
    //   float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.;
    float temperature = sensors.getTempC(D[i]);
    // Only send data if temperature has changed and no error
#if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
#else
    if (temperature != -127.00 && temperature <= 85.00) {
#endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature, 1));
      // Save new temperatures for next compare
      lastTemperature[i] = temperature;
    }
  }

  for (int i = 0; i < 5; i++) {
    int value = analogRead(i);
    /*Serial.print("Pin");
      Serial.print(i);
      Serial.print("=");
      Serial.println(value);
    */
    int j = i + ATTACHED_DS18B20;
    if (value > 150) {
      send(heat.setSensor(j).set(1));
    }
    else {
      send(heat.setSensor(j).set(0));
    }
  }

  sleep(SLEEP_TIME);
}

C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':

Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'

sensors.requestTemperatures();

^

exit status 1
expected initializer before 'sensors'

mfalkvidd

@pepson you’re missing a } before start of loop.

pepson

@mfalkvidd
Where ? please show me more.... :( i am beginner

pepson

@pepson ok fixed it :)

pepson

But.... Can you also help me to add to this sketch option to send to example to Home Assistant also DESCRIPTION to each sensors ? And description will be get from sketch from name about address sensor ?

As in this sketch which i have for relay:

#define USE_EXPANDER
// Enable debug prints to serial monitor
//#define MY_DEBUG

#define MY_GATEWAY_SERIAL

#include <MySensors.h>
#include <Bounce2.h>
#ifdef USE_EXPANDER
  #include <Wire.h>    // Required for I2C communication
  #include "PCF8574.h"
  uint8_t expanderAddresses[] = {0x20};
  const int numberOfExpanders = sizeof(expanderAddresses);
  PCF8574 expander[numberOfExpanders];
  #define E(expanderNo, ExpanderPin) (((expanderNo+1)<<8) | (ExpanderPin))
#endif

// No Button Constant
#define NOB -1
#define MULTI_RELAY_VERSION 9
#define RELAY_STATE_STORAGE 1

const uint8_t RELAY_TRIGGER_LOW  = 0;
const uint8_t RELAY_TRIGGER_HIGH = 1;
const uint8_t RELAY_STARTUP_ON   = 2;
const uint8_t RELAY_STARTUP_OFF  = 4;
const uint8_t RELAY_STARTUP_MASK = RELAY_STARTUP_ON | RELAY_STARTUP_OFF;

enum ButtonType {
  MONO_STABLE = 0,
  BI_STABLE = 1,
  DING_DONG = 2 // HIGH state immediatly after push, LOW state after release
};

typedef struct {
  int sensorId;
  int relay;
  int button;
  uint8_t relayOptions;
  ButtonType buttonType;
  const char * relayDescription;
} RelayButton;

// CONFIGURE ONLY THIS ARRAY!
// Row params: sensor ID - sensor ID reported on MySensor Gateway
//             relay pin - Expander supported
//             button pin - <0 for virtual buttons (only available in MySensor Gateway); no support for Expander
//             relay options - [RELAY_TRIGGER_LOW|RELAY_TRIGGER_HIGH] {RELAY_STARTUP_ON|RELAY_STARTUP_OFF}
//             button type - [MONO_STABLE|BI_STABLE|DING_DONG]
//             relay description - reported on MySensor Gateway, can help identify device on initial configuration in Home Automation App, can be empty ("")
RelayButton myRelayButtons[] = {
  {0, 2, A0, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł2 - kinkiet [C10]"},  // WŁ: Ł2
  {1, 16, A1, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 2 [A9]"},  // WŁ: Salon 2
  {2, 15, A2, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 1 [A10]"},  // WŁ: Salon 1
  {3, E(0,1), A3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, BI_STABLE, "Halogen - Taras [B8]"},  // WŁ: Taras
  {4, 22, A4, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia [B2]"},  // WŁ: Kuchnia 1
  {5, 23, A5, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia - Kinkiet [B3]"},  // WŁ: Kuchnia 2
  {6, 28, A6, RELAY_TRIGGER_LOW, BI_STABLE, "Jadalnia 2 [A4]"},  // WŁ: Hall I/Jadalnia prawy
  {17, 17, A7, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Kinkiet [A11]"},  // WŁ: Hall I/Ł1 prawy
  {8, 31, A8, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"},  // WŁ: Kotłownia/Garaż
  {8, 31, A9, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"},  // WŁ: Garaż
  {10, 14, A10, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, BI_STABLE, "Halogen - wejście [B4]"},  // WŁ: Drzwi wejściowe
  {11, E(0,7), A11, RELAY_TRIGGER_LOW, DING_DONG, "Dzwonek [?]"},  // WŁ: Dzwonek
  {12, 29, A12, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Jadalnia lewy
  {12, 29, A13, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Wiatrołap
  {14, 32, A14, RELAY_TRIGGER_LOW, BI_STABLE, "Wiatrołap [A8]"},  // WŁ: Wiatrołap/Hall I
  {15, 19, A15, RELAY_TRIGGER_LOW, MONO_STABLE, "Kotłownia [B1]"},  // WŁ: Kotłownia/Hall I
  {16, 24, 53, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Taśma LED [C1]"},  // WŁ: Hall I/Ł1 środek
  {17, 17, 52, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł1 - Kinkiet [A11]"},  // WŁ: Ł1
  {18, 18, 51, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 [A12]"},  // WŁ: Hall I/Ł1 lewy
  {19, 6, 50, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"},  // WŁ: Hall I/Schody 1
  {12, 29, 49, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"},  // WŁ: Hall I/Schody 2
  {21, 26, 48, RELAY_TRIGGER_LOW, BI_STABLE, "Gabinet [A2]"},  // WŁ: Gabinet
  {22, 7, 47, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"},  // WŁ: Hall II/Schody 1
  {19, 6, 46, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"},  // WŁ: Hall II/Schody 2
  {24, 10, 45, RELAY_TRIGGER_LOW, BI_STABLE, "Garderoba [C12]"},  // WŁ: Garderoba
  {25, 4, 44, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad kuchnią 2 [B10]"},  // WŁ: Pok. nad kuchnią 2
  {26, 5, 43, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad kuchnią 1 [B9]"},  // WŁ: Pok. nad kuchnią 1
  {27, 8, 42, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad salonem 2 [B12]"},  // WŁ: Pok. nad salonem 2
  {28, 9, 41, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad salonem 1 [B11]"},  // WŁ: Pok. nad salonem 1
  {29, 3, 40, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 [C7]"},  // WŁ: Hall II/Ł2 1
  {30, E(0,3), 39, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 - Taśma LED [?]"},  // WŁ: Hall II/Ł2 2
  {22, 7, 38, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"},  // WŁ: Hall II/Sypialnia
  {32, 11, 37, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 2 [C9]"},  // WŁ: Sypialnia 2
  {33, 12, 36, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 1 [C8]"},  // WŁ: Sypialnia 1
  {34, 25, -1, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, MONO_STABLE, "Halogen - Garaż [A1]"},  // WŁ: Virtual Button 1
  {35, 30, -2, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł1 - Wentylator [A3]"},  // WŁ: Virtual Button 2
  {36, E(0,2), -3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Halogen - wschód [B6]"},  // WŁ: Virtual Button 3
  {37, E(0,4), -4, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki schodowe [C6]"},  // WŁ: Virtual Button 4
  {38, E(0,5), -5, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe I [C4]"},  // WŁ: Virtual Button 5
  {39, E(0,6), -6, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe II [C2]"},  // WŁ: Virtual Button 6
  {40, E(0,0), -7, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł2 - wentylator [C11]"},  // WŁ: Virtual Button 7
};

const int numberOfRelayButtons = sizeof(myRelayButtons) / sizeof(RelayButton);

typedef struct {
  int firstButton;
  int nextButton;
} RelayMultiButtons;

RelayMultiButtons relayMultiButtons[numberOfRelayButtons];
uint8_t myRelayState[numberOfRelayButtons];

// MySensors - Sending Data
// To send data you have to create a MyMessage container to hold the information.
MyMessage msgs[numberOfRelayButtons];

Bounce myButtonDebouncer[numberOfRelayButtons];

//Function Declaration
uint8_t loadRelayState(int relayNum, uint8_t forceEeprom = 0);
void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom);
void saveRelayState(int relayNum, uint8_t state);
void changeRelayState(int relayNum, uint8_t relayState);



// MySensors - This will execute before MySensors starts up
void before() {
  Serial.begin(115200);
  
  #ifdef USE_EXPANDER
    /* Start I2C bus and PCF8574 instance */
    for(int i = 0; i < numberOfExpanders; i++) {
      expander[i].begin(expanderAddresses[i]);
    }
  #endif
  
  // initialize multiple buttons list structure
  for (int i = 0; i < numberOfRelayButtons; i++) {
    relayMultiButtons[i].firstButton = -1;
    relayMultiButtons[i].nextButton = -1;
  }
  // find multiple buttons for the same relay (uni-directional list)
  for (int i = 0; i < numberOfRelayButtons-1; i++) {
    if (relayMultiButtons[i].firstButton == -1) {
      int prevRelayButton = i;
      for (int j = i+1; j < numberOfRelayButtons; j++) {
        if (myRelayButtons[i].relay == myRelayButtons[j].relay) {
          relayMultiButtons[prevRelayButton].firstButton = i;
          relayMultiButtons[prevRelayButton].nextButton = j;
          relayMultiButtons[j].firstButton = i;
          prevRelayButton = j;
        }
      }
    }
  }
  
  // if version has changed, reset state of all relays
  int versionChangeResetState = (MULTI_RELAY_VERSION == loadState(0) ) ? 0 : 1;
  
  for (int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, load only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      // Then set relay pins in output mode
      #ifdef USE_EXPANDER
        if ( myRelayButtons[i].relay & 0xff00 ) {
          // EXPANDER
          int expanderNo = (myRelayButtons[i].relay >> 8) - 1;
          int expanderPin = myRelayButtons[i].relay & 0xff;
          expander[expanderNo].pinMode(expanderPin, OUTPUT);
        } else {
      #endif
          pinMode(myRelayButtons[i].relay, OUTPUT);
      #ifdef USE_EXPANDER
        }
      #endif
      
      uint8_t isTurnedOn = 0;
      
      if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) {
        isTurnedOn = 1;
      } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) {
      } else {
        // Set relay to last known state (using eeprom storage)
        isTurnedOn = loadRelayState(i, 1); // 1 - true, 0 - false
        if (versionChangeResetState && isTurnedOn) {
          saveRelayState(i, 0, 1);
          isTurnedOn = 0;
        }
      }

      changeRelayState(i, isTurnedOn);
      myRelayState[i] = isTurnedOn;
    }
  }
  if (versionChangeResetState) {
    // version has changed, so store new version in eeporom
    saveState(0, MULTI_RELAY_VERSION);
  }
}

// executed AFTER mysensors has been initialised
void setup() {
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0) {
      // No Expander support for buttons (de-bouncing)
      pinMode(myRelayButtons[i].button, INPUT_PULLUP); // HIGH state when button is not pushed
    }
  }
  // Setup locally attached sensors
  delay(5000);
  // Send state to MySensor Gateway
  for(int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, send only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      msgs[i] = MyMessage(myRelayButtons[i].sensorId, V_LIGHT);
      uint8_t relayState;
      if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) {
        relayState = 1;
      } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) {
        relayState = 0;
      } else {
        relayState = loadRelayState(i);
      }
      send(msgs[i].set(relayState)); // send current state
    }
  }
  // Setup buttons
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0) {
      // setup debouncer
      myButtonDebouncer[i] = Bounce();
      myButtonDebouncer[i].attach(myRelayButtons[i].button);
      myButtonDebouncer[i].interval(50);
    }
  }
}

void loop() {
  for(int i = 0; i < numberOfRelayButtons; i++) {
    if (myRelayButtons[i].button >= 0 && myButtonDebouncer[i].update()) {
      int buttonState = myButtonDebouncer[i].read();
      #ifdef MY_DEBUG
        Serial.print("# Button ");
        Serial.print(i);
        Serial.print(" changed to: ");
        Serial.println(buttonState);
      #endif
      
      int relayNum = (relayMultiButtons[i].firstButton == -1) ? i : relayMultiButtons[i].firstButton;
      
      if (myRelayButtons[i].buttonType == DING_DONG) {
        if (buttonState == LOW) { // button pressed
          changeRelayState(relayNum, 1);
          send(msgs[relayNum].set(1));
        } else { // button released
          changeRelayState(relayNum, 0);
          send(msgs[relayNum].set(0));
        }
      } else if (myRelayButtons[i].buttonType == BI_STABLE || buttonState == HIGH) {
        // If button type is BI_STABLE, any change will toggle relay state
        // For MONO_STABLE, button must be pushed and released (HIGH)
        uint8_t isTurnedOn = ! loadRelayState(relayNum); // 1 - true, 0 - false
        changeRelayState(relayNum, isTurnedOn);
        send(msgs[relayNum].set(isTurnedOn));
        saveRelayState(relayNum, isTurnedOn);
      }
    }
  }
}



// MySensors - Presentation
// Your sensor must first present itself to the controller.
// The presentation is a hint to allow controller prepare for the sensor data that eventually will come.
// Executed after "before()" and before "setup()" in: _begin (MySensorsCore.cpp) > gatewayTransportInit() > presentNode()
void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Multi Relay", "1.2");
  
  // Register every relay as separate sensor
  for (int i = 0; i < numberOfRelayButtons; i++) {
    // if this relay has multiple buttons, register only first
    if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) {
      // Register all sensors to gw (they will be created as child devices)
      // void present(uint8_t childSensorId, uint8_t sensorType, const char *description, bool ack);
      //   childSensorId - The unique child id you want to choose for the sensor connected to this Arduino. Range 0-254.
      //   sensorType - The sensor type you want to create.
      //   description An optional textual description of the attached sensor.
      //   ack - Set this to true if you want destination node to send ack back to this node. Default is not to request any ack.
      present(myRelayButtons[i].sensorId, S_BINARY, myRelayButtons[i].relayDescription);
    }
  }
}


// MySensors - Handling incoming messages
// Nodes that expects incoming data, such as an actuator or repeating nodes,
// must implement the receive() - function to handle the incoming messages.
// Do not sleep a node where you expect incoming data or you will lose messages.
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type == V_STATUS) {
    uint8_t isTurnedOn = message.getBool(); // 1 - true, 0 - false
    changeRelayState(message.sensor, isTurnedOn);
    // Store state in eeprom if changed
    if (loadRelayState(message.sensor) != isTurnedOn) {
      saveRelayState(message.sensor, isTurnedOn);
    }
    send(msgs[message.sensor].set(isTurnedOn)); // support for OPTIMISTIC=FALSE (Home Asistant)
    #ifdef MY_DEBUG
      // Write some debug info
      Serial.print("# Incoming change for sensor: " + message.sensor);
      Serial.println(", New status: " + isTurnedOn);
    #endif
  }
}

uint8_t loadRelayState(int relayNum, uint8_t forceEeprom) {
  uint8_t relayState;
  if (forceEeprom) {
    relayState = loadState(RELAY_STATE_STORAGE + relayNum);
  } else {
    relayState = myRelayState[relayNum];
  }
  #ifdef MY_DEBUG
    Serial.print("# loadRelayState: ");
    Serial.print(relayNum);
    if (forceEeprom) {
      Serial.print("(byte ");
      Serial.print(RELAY_STATE_STORAGE + relayNum);
      Serial.print(")");
    }
    Serial.print(" = ");
    Serial.println(relayState);
  #endif
  return(relayState);
}

void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom) {
  
  int mainRelayNum = (relayMultiButtons[relayNum].firstButton == -1) ? relayNum : relayMultiButtons[relayNum].firstButton;
  
  myRelayState[mainRelayNum] = state;
  if (useEeprom && (relayNum == mainRelayNum)) {
    saveState(RELAY_STATE_STORAGE + mainRelayNum, state);
  }
  
  int nextButton = mainRelayNum;
  // update all buttons
  while ((nextButton = relayMultiButtons[nextButton].nextButton) != -1) {
    myRelayState[nextButton] = state;
  };
}

void saveRelayState(int relayNum, uint8_t state) {
  uint8_t useEeprom = ((myRelayButtons[relayNum].relayOptions & RELAY_STARTUP_MASK) == 0);
  saveRelayState(relayNum, state, useEeprom);
}

void changeRelayState(int relayNum, uint8_t relayState) {
  
  uint8_t relayTrigger = myRelayButtons[relayNum].relayOptions & RELAY_TRIGGER_HIGH;
  uint8_t digitalOutState = relayState ? relayTrigger : ! relayTrigger;
  
  #ifdef USE_EXPANDER
    if ( myRelayButtons[relayNum].relay & 0xff00 ) {
      int expanderNo = (myRelayButtons[relayNum].relay >> 8) - 1;
      int expanderPin = myRelayButtons[relayNum].relay & 0xff;
      expander[expanderNo].digitalWrite(expanderPin, digitalOutState);
    } else {
  #endif
    digitalWrite(myRelayButtons[relayNum].relay, digitalOutState);
  #ifdef USE_EXPANDER
    }
  #endif
}

And in Home assistant show example decription: Ł2 - kinkiet [C10] or for second Salon 2 [A9] etc.
Please help me... because it will be good to identify sensors when add to Controller.

About DS18B20 onewire.

11

12.0k

11.2k

113.4k