Problem with battery powered temperature sensor

waspie

I'm having an issue where a simple temperature sensor sketch works fine powered by the ftdi serial converter but when powered by 2xAA batteries something isn't working right.

Log from when it's powered by 3.3v and working correctly:

77 TSM:INIT
77 TSF:WUR:MS=0
86 TSM:INIT:TSP OK
86 TSM:INIT:STATID=5
90 TSF:SID:OK,ID=5
92 TSM:FPAR
126 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
905 TSF:MSG:READ,0-0-5,s=255,c=3,t=8,pt=1,l=1,sg=0:0
911 TSF:MSG:FPAR OK,ID=0,D=1
2136 TSM:FPAR:OK
2136 TSM:ID
2138 TSM:ID:OK
2140 TSM:UPL
2146 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2152 TSF:MSG:READ,0-0-5,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2158 TSF:MSG:PONG RECV,HP=1
2162 TSF:MSG:READ,0-0-5,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2168 !TSF:MSG:PONG RECV,INACTIVE
2170 TSM:UPL:OK
2172 TSM:READY:ID=5,PAR=0,DIS=1
2179 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2187 TSF:MSG:READ,0-0-5,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2205 TSF:MSG:SEND,5-5-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.1
2217 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4227 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Temperature Sensor
4243 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.1
4257 TSF:MSG:SEND,5-5-0-0,s=0,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
4265 MCO:REG:REQ
4268 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4276 TSF:MSG:READ,0-0-5,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4282 MCO:PIM:NODE REG=1
4284 MCO:BGN:STP
4290 TSF:MSG:SEND,5-5-0-0,s=1,c=0,t=30,pt=0,l=0,sg=0,ft=0,st=OK:
4298 MCO:BGN:INIT OK,TSP=1
4302 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
4308 TSF:TDI:TSL
4311 MCO:SLP:WUP=-1
4313 TSF:TRI:TSB
4349 TSF:MSG:SEND,5-5-0-0,s=0,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:28.0
4362 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:100
4372 TSF:MSG:SEND,5-5-0-0,s=1,c=1,t=38,pt=7,l=5,sg=0,ft=0,st=OK:3.39
4380 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
4386 TSF:TDI:TSL

log from when it's not working:

16 MCO:BGN:INIT NODE,CP=RNNNA---,REL=255,VER=2.3.1
26 MCO:BGN:BFR
30 TSM:INIT
30 TSF:WUR:MS=0
38 TSM:INIT:TSP OK
40 TSM:INIT:STATID=5
43 TSF:SID:OK,ID=5
45 TSM:FPAR
79 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1054 TSF:MSG:READ,0-0-5,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1060 TSF:MSG:FPAR OK,ID=0,D=1
2091 TSM:FPAR:OK
2091 TSM:ID
2093 TSM:ID:OK
2095 TSM:UPL
2099 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2107 TSF:MSG:READ,0-0-5,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2113 TSF:MSG:PONG RECV,HP=1
2115 TSM:UPL:OK
2117 TSM:READY:ID=5,PAR=0,DIS=1
2121 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2129 TSF:MSG:READ,0-0-5,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2140 TSF:MSG:SEND,5-5-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.3.1
2150 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4161 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Temperature Sensor
4171 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.1
4179 MCO:REG:REQ
4184 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4190 TSF:MSG:READ,0-0-5,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4196 MCO:PIM:NODE REG=1
4200 MCO:BGN:STP
4202 TSF:MSG:SEND,5-5-0-0,s=1,c=0,t=30,pt=0,l=0,sg=0,ft=0,st=OK:
4210 MCO:BGN:INIT OK,TSP=1
4214 MCO:SLP:MS=94,SMS=0,I1=255,M1=255,I2=255,M2=255
4220 TSF:TDI:TSL
4222 MCO:SLP:WUP=-1
4225 TSF:TRI:TSB
4231 MCO:SLP:MS=30000,SMS=0,I1=255,M1=255,I2=255,M2=255
4237 TSF:TDI:TSL

sketch:

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller
 * http://www.mysensors.org/build/temp
 */


// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_RF24
//#define MY_RADIO_RFM69
#define MY_NODE_ID 5
#include <SPI.h>
#include <MySensors.h>  
#include <DallasTemperature.h>
#include <OneWire.h>

#define BATT_SENSOR

#ifdef BATT_SENSOR
#define REPORT_VOLTAGE
#endif

#define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 4 // Pin where dallase sensor is connected
#define ONE_WIRE_GND 5
#define ONE_WIRE_VCC 3
 
#define MAX_ATTACHED_DS18B20 16
unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
const uint8_t TEMP_TIME = 12; //at least every nth time battery is reported
const uint8_t BATT_TIME = 12; //when also BATT-LEVEL is reportet
const float BATT_100 = 3; //3.3V for CR2032, 3V for 2xAA
const float BATT_0 = 2.2;
//float lastTemperature;
uint8_t lastTempSent = 0;//, lastHumSent = 0;
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
bool receivedConfig = false;
bool metric = true;
// Initialize temperature message
MyMessage msg(0,V_TEMP);
#ifdef REPORT_VOLTAGE
MyMessage msgBatt(1, V_VOLTAGE);
#endif
#ifdef BATT_SENSOR
uint8_t battReport = BATT_TIME - 1; //First report at startup
long oldvalue = 0;
#endif

void before()
{

#ifdef ONE_WIRE_VCC
  pinMode(ONE_WIRE_VCC, OUTPUT);
  digitalWrite(ONE_WIRE_VCC, HIGH);
#endif

#ifdef ONE_WIRE_GND
  pinMode(ONE_WIRE_GND, OUTPUT);
  digitalWrite(ONE_WIRE_GND, LOW);
#endif

  #ifdef VCCGND_PINS
  pinMode(VCC, OUTPUT);
  digitalWrite(VCC, HIGH);
  pinMode(GND, OUTPUT);
  digitalWrite(GND, LOW);
  #endif
  
  // Startup up the OneWire library
  sensors.begin();
}

void setup()  
{ 
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);

  #ifdef REPORT_VOLTAGE
  present(1, S_MULTIMETER);
#endif

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Temperature Sensor", "1.1");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
}

void loop()     
{     
   boolean tempsent = false;
   
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
      lastTempSent = 0;
      tempsent = true;
    }
  }
  #ifdef BATT_SENSOR
  if (++battReport >= BATT_TIME && tempsent) {

    //gw.sleep(10);
    long value = readVcc();


    if (value != oldvalue) {
      int percent = (( (float)(value) / 1000 ) - BATT_0) / (BATT_100 - BATT_0) * 100;
      percent = (percent > 100) ? 100 : percent;
      percent = (percent < 0) ? 0 : percent;
      sendBatteryLevel(percent);
#ifdef REPORT_VOLTAGE
      send(msgBatt.set((float)(value) / 1000, 2));
#endif
    }
    oldvalue = value;
    battReport = 0;
  }
#endif
  sleep(SLEEP_TIME);
}

long readVcc() {
  // Read 1.1V reference against AVcc
  // set the reference to Vcc and the measurement to the internal 1.1V reference
#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
  ADMUX = _BV(REFS0) | _BV(MUX4) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);
#elif defined (__AVR_ATtiny24__) || defined(__AVR_ATtiny44__) || defined(__AVR_ATtiny84__)
  ADMUX = _BV(MUX5) | _BV(MUX0);
#elif defined (__AVR_ATtiny25__) || defined(__AVR_ATtiny45__) || defined(__AVR_ATtiny85__)
  ADMUX = _BV(MUX3) | _BV(MUX2);
#else
  ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);
#endif

  delay(2); // Wait for Vref to settle
  ADCSRA |= _BV(ADSC); // Start conversion
  while (bit_is_set(ADCSRA, ADSC)); // measuring

  uint8_t low  = ADCL; // must read ADCL first - it then locks ADCH
  uint8_t high = ADCH; // unlocks both

  long result = (high << 8) | low;

  result = 1125300L / result; // Calculate Vcc (in mV); 1125300 = 1.1*1023*1000
  return result; // Vcc in millivolts
}

i tried a 47uf cap that I had laying around on the AA setup but nothing changes...

mfalkvidd

@waspie both log files look good. Could you describe the problem you are experiencing?

waspie

@mfalkvidd said in Problem with battery powered temperature sensor:

Could you describe the problem you are experiencing?

The temperature/voltage isn't being sent when battery powered.
from the good log:

4349 TSF:MSG:SEND,5-5-0-0,s=0,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:28.0  <---temperature
4362 TSF:MSG:SEND,5-5-0-0,s=255,c=3,t=0,pt=1,l=1,sg=0,ft=0,st=OK:100 <---battery percentage
4372 TSF:MSG:SEND,5-5-0-0,s=1,c=1,t=38,pt=7,l=5,sg=0,ft=0,st=OK:3.39 <---- vcc voltage

but those items aren't sent when it is powered by 2xAA. Also, it doesn't seem to go to sleep or wakeup (one or the other).

If I keep watching the serial log while battery powered it never does anything more. Not after the allotted 30 seconds or longer. As if it is stuck.

mfalkvidd

Thanks for clarifying @waspie
~~Could you post your sketch?~~
EDIT: Sorry, you already did that. I'll take a look at it.

mfalkvidd

I can't see anything that looks odd in the sketch. Easiest way to troubleshoot is probably to add Serial.println statements to see where the code execution stops.

waspie

i stripped out enough stuff to see it post 85 degrees the first time around. after that it is reporting the temperature consistently on battery (including going to sleep, waking up, reporting, and going back to sleep).

Any thoughts on why it fails the first time through?

My hack solution would be to remove the check and let it throw out 85 the first time through and discard that on the other send (openhab) but surely there's a better way?

waspie

This post is deleted!

nekitoss

Hi, @waspie !

First of all i'd like to say about value "85" - according to DS18B20 datasheet page 6, note after table 4.1: *The power-on reset value of the temperature register is +85°C.

Your code looks fine and similar to my mains-powered DS18B20 sensor (because we used same example).

I have some thoughts:

you may have power problems:
a. from logs i see that you have 1 sensor, but you left defined #define MAX_ATTACHED_DS18B20 16 . If (suddenly) you would have 16 sensors - when you ask them for conversion they would consume 16* 1.5mA(max at 5v) = 24mA which is above recomended 20mA for atmega pin
b. you are powering from battery: DS18B20 oficially requres minimum of 3 v (as for datasheet). People say that with lower voltage it may have strange readings or even do not work at all
c. you are powering from battery through pin: is voltage raise fast enougth before start reading? is voltage drop low enought so voltage supplied to ds18b20 is >=3v?
i'd suggest you to measure voltages (but multimeter won't show you short drop-outs when start conmsuming) and try to feed VCC of DS18b20 directly from power source. If not possible - at least measure voltage and try to add some wait() after powering up pin (or also before measure start or after sleep).
When running from 3v, what frequency of atmega processor is? If it is 16mHz - that it is not in safe operating area for that voltage. you should run 8 mHz. (>=2.4v for 8mHz and >=3.78v for 16mHz)

Also i suggest you try to change sleep(conversionTime); with wait(conversionTime); and check if it will change anything (especially when ds18b20 directly powered from source). Also try with fresh batteries.

If nothing helped, then for "85" value simple solution will be

if (temperature != 85)
    send();

because it is very rarely that people need to measure 85 degrees of Celsius at home...

~~ ~~
For advanced battery-powering i highly recommend to read this. Also you can find there about frequency vs voltage.

And for internal battery voltage reading:
i don't remember where i found it: here1 or here2 or somwhere else..
but you may want to get more accurate readings by measuring and setting Internal Reference Voltage value and using it in the code, and give it some time to stabilize and/or use some type of averaging.

Sebex

@nekitoss very helpful and clear post regarding battery powering!
I have Atmega328 16mhz, is it possible to change the 16 to 8mhz so that it can be powered by two AA batteries?

olka

@Sebex The quickest way is to upload a new bootloader that use the Atmega 8mhz internal oscillator, like this one: https://github.com/MCUdude/MiniCore
As serial timing will be less accurate with the internal oscillator you might also need to include #define MY_BAUD_RATE 9600 in your scetch.

@waspie Did you try using Serial.print for step by step debugging to narrow in on the issues? For example; in the function readVcc(), what is the actual returned value when running on batteries? and so on...

Sebex

This post is deleted!

waspie

@olka
Can't say I remember what I did anymore. Probably suppressed sending in the case of 85 degrees.

Problem with battery powered temperature sensor

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

Sensebender Gateway (SAMD21)
Development • • pikim

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

LAN8720A - will mysensors work with this module
Development • • Marcin

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Problem with battery powered temperature sensor

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden) Announcements • • hek

MYSController with MQTT Gateway (via Node Red) Development • • slt1

MQTT GW on ESP8266 supporting SSL/TLS? Development • esp8266 mqtt gw • • bgunnarb

Sensebender Gateway (SAMD21) Development • • pikim

Counting Incoming and Outgoing Messages from a Gateway Development • • Trand

LAN8720A - will mysensors work with this module Development • • Marcin

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • • hek

MYSController with MQTT Gateway (via Node Red)
Development • • slt1

MQTT GW on ESP8266 supporting SSL/TLS?
Development • esp8266 mqtt gw • • bgunnarb

Sensebender Gateway (SAMD21)
Development • • pikim

Counting Incoming and Outgoing Messages from a Gateway
Development • • Trand

LAN8720A - will mysensors work with this module
Development • • Marcin

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts