Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Can I on ESP32 used together rf24+nrf69?

bladeback last edited by

I want make ES32 multi gateway with modul rf24 and rfm69, because i have one node rf24 and one node rfm69.
Please help me. If it is possible, how set in sketch?
Reply Quote 0
1 Reply Last reply
Yveaux Mod last edited by @bladeback

@bladeback sorry, but it is not possible at the moment, as mySensors only supports one radio at a time.
Reply Quote 0
1 Reply Last reply

2
Posts

432
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2570
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

17

0
Votes

17
Posts

166
Views

LiFePO4 batteries are a great choice because they have a long life cycle and are much safer than other lithium-based batteries. However, you need a solar charge controller that’s compatible with LiFePO4 to prevent overcharging and maintain efficiency. A good MPPT controller can significantly boost energy harvest from your panels. Also, ensure your solar panel output matches your power needs. If you're in solar ireland, you might find some local companies that offer tailored solutions for maximizing solar efficiency in lower light conditions.
GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

15

0
Votes

15
Posts

123
Views

@eiten Ran into the same error but of course the community is always at hand, ready to help! Great! I'm using MySensors 2.3.2 release version. Downgrading the ESP8266 board library to 2.7.4 as suggested by @OldSurferDude did the trick. I'm still clinging to MySensors. So simple and inexpensive to use! All sensors and other stuff connects over three MQTT GW in three locations back to my Home Assistant. PS: Get well soon! Regards, Gunnar
Gateway on Raspberry pi 1
General Discussion • • mimaret

9

0
Votes

9
Posts

44
Views

@mimaret It was a pleasure. Thank you for your feedback!
What's a good power bank for use with IoT?
General Discussion • • NeverDie

20

1
Votes

20
Posts

179
Views

@OldSurferDude Thanks a very valued to know. I was wondering today why my (big) powerbanks fall down after short time. I have small 1 & 2-pieces powerbanks, they work very well. I use also BSM hw-168 or hw-107 for charging single 18650. Will try to use them outside also with small solarpanels.
Old hardware migration
General Discussion • • dbemowsk

3

0
Votes

3
Posts

38
Views

@OldSurferDude My old 2.0 setup is with nRF24L01 radios. This is a link to the thread on some light switches that I designed and built. https://forum.mysensors.org/topic/7376/us-decora-wall-switch-continued/2 I am aware that you cannot have two MQTT gatways. When I designed my old setup I was not that familiar with MQTT so I never ended up implementing it. On the home assistant server that I have set up though, I have installed the MQTT broker on there so I should be able to comunicate with any MySensors stuff over MQTT in the future devices I make/set up. As I mentioned, I do have a Home Assistant box that I have started about 4 months ago and eventually want to migrate my Vera equipment to the HA box. As for the YAML and Python, I'll muddle my way through. used to program in PHP and have done enough on Arduino that I'm sure it won't hurt my brain too much.

Can I on ESP32 used together rf24+nrf69?

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

Gateway on Raspberry pi 1
General Discussion • • mimaret

What's a good power bank for use with IoT?
General Discussion • • NeverDie

Old hardware migration
General Discussion • • dbemowsk

15
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Can I on ESP32 used together rf24+nrf69?

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

Need advice on solar powering with LiFePo4 battery General Discussion • • willemx

GatawayESP8266 - Compile error General Discussion • gatawayesp8266 compile error • • skom

Gateway on Raspberry pi 1 General Discussion • • mimaret

What's a good power bank for use with IoT? General Discussion • • NeverDie

Old hardware migration General Discussion • • dbemowsk

15Online

11.4kUsers

11.1kTopics

112.7kPosts

Update RF24 library to latest version
Bug Reports • • andriej

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

Gateway on Raspberry pi 1
General Discussion • • mimaret

What's a good power bank for use with IoT?
General Discussion • • NeverDie

Old hardware migration
General Discussion • • dbemowsk

15
Online

11.4k
Users

11.1k
Topics

112.7k
Posts