NodeID assignment not working? MY_INCLUSION_MODE_FEATURE enabled

[bebr]

Hi,

The myscontroller node does not seem to assign IDs.
Only nodes with a defined MY_NODE_ID work.
MY_INCLUSION_MODE_FEATURE is enabled on the gateway.
Pressing the button does not change the behavior (I see taht the inclusion mode is enabled when I press the button, and resets after 60s)

When I omit the MY_NODE_ID in my sketch, the node keeps asking for a node id several times.
On the NodeRED side, I connected a debug msg node at the output of the myscontroller node.
The debug shows that a different ID is tried but the sqlite base is not populated and the asking node does not receive the ID.
Do I need to connect the myscontroller output to the input of the gateway to send a message back to the node?

Here is the node debug messages:

16 MCO:BGN:INIT NODE,CP=RNNNA---,FQ=16,REL=255,VER=2.3.2
26 TSM:INIT
28 TSF:WUR:MS=0
34 TSM:INIT:TSP OK
36 TSM:FPAR
38 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2048 !TSM:FPAR:NO REPLY
2050 TSM:FPAR
2052 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4060 !TSM:FPAR:NO REPLY
4062 TSM:FPAR
4064 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6072 !TSM:FPAR:NO REPLY
6074 TSM:FPAR
6076 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8084 !TSM:FPAR:FAIL
8085 TSM:FAIL:CNT=1
8087 TSM:FAIL:DIS  
8089 TSF:TDI:TSL   
18091 TSM:FAIL:RE-INIT
18093 TSM:INIT        
18099 TSM:INIT:TSP OK
18101 TSM:FPAR
18104 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
18848 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
18853 TSF:MSG:FPAR OK,ID=0,D=1
20112 TSM:FPAR:OK
20113 TSM:ID
20115 TSM:ID:REQ
20117 TSF:MSG:SEND,255-255-0-0,s=147,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
22125 TSM:ID
22126 TSM:ID:REQ
22129 TSF:MSG:SEND,255-255-0-0,s=110,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
24136 TSM:ID
24137 TSM:ID:REQ
24140 TSF:MSG:SEND,255-255-0-0,s=73,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
26147 TSM:ID    
26148 TSM:ID:REQ
26151 TSF:MSG:SEND,255-255-0-0,s=36,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
28160 !TSM:ID:FAIL
28161 TSM:FAIL:CNT=2
28163 TSM:FAIL:DIS
28165 TSF:TDI:TSL
38168 TSM:FAIL:RE-INIT
38170 TSM:INIT
38176 TSM:INIT:TSP OK
38178 TSM:FPAR
38181 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
38538 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
38543 TSF:MSG:FPAR OK,ID=0,D=1
40190 TSM:FPAR:OK
40192 TSM:ID
40194 TSM:ID:REQ
40196 TSF:MSG:SEND,255-255-0-0,s=2,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
42203 TSM:ID
42204 TSM:ID:REQ
42207 TSF:MSG:SEND,255-255-0-0,s=220,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
44214 TSM:ID
44215 TSM:ID:REQ
44218 TSF:MSG:SEND,255-255-0-0,s=183,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
46225 TSM:ID
46226 TSM:ID:REQ
46229 TSF:MSG:SEND,255-255-0-0,s=146,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
48236 !TSM:ID:FAIL
48237 TSM:FAIL:CNT=3
48239 TSM:FAIL:DIS
48241 TSF:TDI:TSL
58244 TSM:FAIL:RE-INIT
58246 TSM:INIT
58252 TSM:INIT:TSP OK
58254 TSM:FPAR
58257 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
60265 !TSM:FPAR:NO REPLY
60267 TSM:FPAR
60270 ?TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
61234 TSF:MSG:READ,0-0-255,s=255,c=3,t=8,pt=1,l=1,sg=0:0
61239 TSF:MSG:FPAR OK,ID=0,D=1
62277 TSM:FPAR:OK
62278 TSM:ID
62280 TSM:ID:REQ
62282 TSF:MSG:SEND,255-255-0-0,s=71,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
64290 TSM:ID
64291 TSM:ID:REQ
64294 TSF:MSG:SEND,255-255-0-0,s=35,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
66302 TSM:ID
66304 TSM:ID:REQ
66307 TSF:MSG:SEND,255-255-0-0,s=0,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
68314 TSM:ID
68315 TSM:ID:REQ
68318 TSF:MSG:SEND,255-255-0-0,s=219,c=3,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
70325 !TSM:ID:FAIL

And here is the message I get from the output of the myscontroller node:

{"payload":"255;6;3;0;4;1","port":"/dev/ttyUSB-MysGW","_msgid":"cd1b9bbf.44ae08","nodeId":255,"childSensorId":6,"messageType":3,"ack":0,"subType":4,"origin":1,"messageTypeStr":"C_INTERNAL","subTypeStr":"I_ID_REQUEST","topicRoot":"mys-out"}
{"payload":"255;225;3;0;4;1","port":"/dev/ttyUSB-MysGW","_msgid":"c0995566.b1b318","nodeId":255,"childSensorId":225,"messageType":3,"ack":0,"subType":4,"origin":1,"messageTypeStr":"C_INTERNAL","subTypeStr":"I_ID_REQUEST","topicRoot":"mys-out"}
{"payload":"255;188;3;0;4;1","port":"/dev/ttyUSB-MysGW","_msgid":"4a91ca08.1fcce4","nodeId":255,"childSensorId":188,"messageType":3,"ack":0,"subType":4,"origin":1,"messageTypeStr":"C_INTERNAL","subTypeStr":"I_ID_REQUEST","topicRoot":"mys-out"}

I don't use MQTT, my gateway is a serial one.

Any clue? thanks a lot.

[bebr]

I reply to myself, I succeeded to make it work.
The \n was missing in the payload before sending it back to the gateway.
This took me months to see this...

Works like a charm now, I just need to implement the inclusion feature in NodeRED.