[SOLVED] Error compiling ESP8266 Gateway sketch
-
I am attempting to setup an esp8266 gateway but getting errors in compilation, using the sketch below (arduino ide 1.8.9 and http://arduino.esp8266.com/stable/package_esp8266com_index.json in board manager, with mysensors 2.3.2 library)
Error:
d/root/Arduino/libraries/MySensors/hal/architecture/ESP8266/MyMainESP8266.cpp: At global scope: /root/Arduino/libraries/MySensors/hal/architecture/ESP8266/MyMainESP8266.cpp:140:27: error: expected initializer before 'ets_intr_lock' extern "C" void IRAM_ATTR ets_intr_lock() ^ Using library MySensors at version 2.3.2 in folder: /root/Arduino/libraries/MySensors Using library SPI at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/SPI Using library ESP8266WiFi at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/ESP8266WiFi Using library EEPROM at version 1.0 in folder: /root/.arduino15/packages/esp8266/hardware/esp8266/2.5.0/libraries/EEPROM exit status 1 Error compiling for board NodeMCU 1.0 (ESP-12E Module).```
/* * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2019 Sensnology AB * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * REVISION HISTORY * Version 1.0 - Henrik Ekblad * Contribution by a-lurker and Anticimex, * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de> * Contribution by Ivo Pullens (ESP8266 support) * * DESCRIPTION * The EthernetGateway sends data received from sensors to the WiFi link. * The gateway also accepts input on ethernet interface, which is then sent out to the radio network. * * VERA CONFIGURATION: * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. * E.g. If you want to use the default values in this sketch enter: 192.168.178.66:5003 * * LED purposes: * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used. * - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - ERR (red) - fast blink on error during transmission error or receive crc error * * See https://www.mysensors.org/build/connect_radio for wiring instructions. * * If you are using a "barebone" ESP8266, see * https://www.mysensors.org/build/esp8266_gateway#wiring-for-barebone-esp8266 * * Inclusion mode button: * - Connect GPIO5 (=D1) via switch to GND ('inclusion switch') * * Hardware SHA204 signing is currently not supported! * * Make sure to fill in your ssid and WiFi password below for ssid & pass. */ // Enable debug prints to serial monitor #define MY_DEBUG // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h #define MY_BAUD_RATE 9600 // Enables and select radio type (if attached) #define MY_RADIO_RF24 //#define MY_RADIO_RFM69 //#define MY_RADIO_RFM95 #define MY_GATEWAY_ESP8266 #define MY_WIFI_SSID "MySSID" #define MY_WIFI_PASSWORD "MyVerySecretPassword" // Enable UDP communication //#define MY_USE_UDP // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below // Set the hostname for the WiFi Client. This is the hostname // it will pass to the DHCP server if not static. #define MY_HOSTNAME "ESP8266_GW" // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP) //#define MY_IP_ADDRESS 192,168,178,87 // If using static ip you can define Gateway and Subnet address as well //#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 //#define MY_IP_SUBNET_ADDRESS 255,255,255,0 // The port to keep open on node server mode #define MY_PORT 5003 // How many clients should be able to connect to this gateway (default 1) #define MY_GATEWAY_MAX_CLIENTS 2 // Controller ip address. Enables client mode (default is "server" mode). // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 //#define MY_CONTROLLER_URL_ADDRESS "my.controller.org" // Enable inclusion mode //#define MY_INCLUSION_MODE_FEATURE // Enable Inclusion mode button on gateway //#define MY_INCLUSION_BUTTON_FEATURE // Set inclusion mode duration (in seconds) //#define MY_INCLUSION_MODE_DURATION 60 // Digital pin used for inclusion mode button //#define MY_INCLUSION_MODE_BUTTON_PIN D1 // Set blinking period //#define MY_DEFAULT_LED_BLINK_PERIOD 300 // Flash leds on rx/tx/err // Led pins used if blinking feature is enabled above //#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin //#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin //#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED #include <MySensors.h> void setup() { // Setup locally attached sensors } void presentation() { // Present locally attached sensors here } void loop() { // Send locally attached sensors data here }
-
@mrhutchinsonmn you seem to be using an old esp arduino core. Could you update that to the latest version and try again?
-
Yes, that was it. Thought it was handled under preferences with the url.
Thank you!
-
@mrhutchinsonmn no prob! Glad I could help.