Detect Interrupt / Timer
-
Hello,
maybe a noob Question but i can´t find an answer:
I want to combine the Motion and the DS18B20 program. So The Temperature is sending every xx minutes, and the Motion Sensor is sending imedently. So I have to detect if the sleep is ending by the Time or The Interrupt. Is there a simple way to detect? The Code is dirty combined, i Know. I will make it better if its possible. Thanks!/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * * Simple binary switch example * Connect button or door/window reed switch between * digitial I/O pin 3 (BUTTON_PIN below) and GND. * http://www.mysensors.org/build/binary */ // Enable debug prints to serial monitor #define MY_DEBUG // Enable and select radio type attached //#define MY_RADIO_NRF24 #define MY_RADIO_RFM69 //#define MY_IS_RFM69HW #define MY_NODE_ID 200 // HW hinten dran = #define MY_IS_RFM69HW wird benötigt // BWM WZ 101 // Test 200 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #include <OneWire.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 4 // Pin where dallase sensor is connected #define MAX_ATTACHED_DS18B20 16 #define BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch #define INTERRUPT BUTTON_PIN-2 int BATTERY_SENSE_PIN = A0; unsigned long SLEEP_TIME = 600000; //12Std = 43200000 OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. float lastTemperature[MAX_ATTACHED_DS18B20]; int numSensors=0; bool receivedConfig = false; bool metric = true; // Initialize temperature message int oldValue=-1; // Change to V_LIGHT if you use S_LIGHT in presentation below MyMessage msg(0,V_TEMP); MyMessage msg1(3,V_TRIPPED); void before() { // Startup up the OneWire library sensors.begin(); } void setup() { // Setup the button pinMode(BUTTON_PIN,INPUT); // Activate internal pull-down digitalWrite(BUTTON_PIN,LOW); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); analogReference(INTERNAL); int sensorValue = analogRead(BATTERY_SENSE_PIN); analogReference(INTERNAL); } void presentation() { // Register binary input sensor to gw (they will be created as child devices) // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. // If S_LIGHT is used, remember to update variable type you send in. See "msg" above. sendSketchInfo("BWM Temp", "1.0"); present(3, S_DOOR); // Fetch the number of attached temperature sensors numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) { present(i, S_TEMP); } } // Check if digital input has changed and send in new value void loop() { // BWM int value = digitalRead(BUTTON_PIN); send(msg1.set(value==HIGH)); // Temp // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) { // Fetch and round temperature to one decimal float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.; // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature != 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature,1)); // Save new temperatures for next compare lastTemperature[i]=temperature; Serial.print(temperature); } } // get the battery Voltage int sensorValue = analogRead(BATTERY_SENSE_PIN); #ifdef MY_DEBUG Serial.println(sensorValue); Serial.println(digitalRead(BUTTON_PIN)); #endif // 1M, 470K divider across battery and using internal ADC ref of 1.1V // Sense point is bypassed with 0.1 uF cap to reduce noise at that point // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts // 3.44/1023 = Volts per bit = 0.003363075 int batteryPcnt = sensorValue *0.9375 -779.375; // Raum Gain Offset // Terrasse 0.9375 -779.375 #ifdef MY_DEBUG float batteryV = sensorValue * 0.003363075; Serial.print("Battery Voltage: "); Serial.print(batteryV); Serial.println(" V"); Serial.print("Battery percent: "); Serial.print(batteryPcnt); Serial.println(" %"); #endif sendBatteryLevel(batteryPcnt); sleep(INTERRUPT,CHANGE,SLEEP_TIME); }
-
Welcome to the forum @Dave2526
Yes. The return value of the sleep call will let you know the reason for waking up. Documentation: https://www.mysensors.org/download/sensor_api_20#sleeping
-
Thats what I think, a really simple thing, Thank You, it works!
resp_sleep=sleep(INTERRUPT,CHANGE,SLEEP_TIME);
and then hust a simple if resp_sleep....
Thanks!
