Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Connecting NodeMCU 1.0 Gateway to WiFi

wint0178 last edited by

Re: Building a WiFi Gateway using ESP8266
I have been able to use the example ESP8266Gateway sketch in Windows version of Arduino IDE to compile the sketch to my NodeMCU. This was possible by downgrading my board library to an earlier version as has been suggested. Now I am getting the following error in serial monitor after entering my SSID and pwrd:

421801 TSM:FAIL:RE-INIT
421826 TSM:INIT
421853 !TSM:INIT:TSP FAIL
421880 TSM:FAIL:CNT=7
421903 TSM:FAIL:DIS
421924 TSF:TDI:TSL

I am trying to connect this gateway to MyController Server on the same Wifi network before adding sensors on other nodes. Ultimately, this will be a multi-node weather station that can report various conditions from nodes placed across a 300+ acre plot of land. I am relatively new to all of this, including arduino and need some help. Thanks in advance.
Reply Quote 0
1 Reply Last reply

1
Posts

7
Views

Suggested Topics

One Arduino with multiple functions
Hardware • • A Former User

17

0
Votes

17
Posts

10080
Views

@tjay4x4 I completely understand. Until about 3-4 weeks ago I did not even know what an Arduino was. Yet, here I am creating a plugin for Indigo (I did not know about Indigo until about 8 weeks ago) and creating/testing very basic sensors. Today I started creating my first 'home-grown' sensor and guess what: You have to try it to understand it I know from experience that you can ask just about anything when you get stuck...
French Version
MyController.org • • JeeLet

1

2
Votes

1
Posts

22
Views

No one has replied
Widgets météo
MyController.org • • JeeLet

1

0
Votes

1
Posts

17
Views

No one has replied
Cannot add Nodes trough RS 485
MyController.org • • qobouky

9

0
Votes

9
Posts

102
Views

@qobouky You are correct, the Binary type sensors should be visible here. I just revisited your sketch and I found a conflict on the allocated sensors id #define CHILD_ID_HUM 0 #define CHILD_ID_TEMP 1 #define CHILD_ID_CO2 2 #define NUMBER_OF_RELAYS 3 // Total number of attached relays void presentation() { present(CHILD_ID_HUM, S_HUM); present(CHILD_ID_TEMP, S_TEMP); present(CHILD_ID_CO2, S_AIR_QUALITY); for (int sensor=1, pin=RELAY_PIN; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) { // Register all sensors to gw (they will be created as child devices) present(sensor, S_BINARY); } } your relay sensor id should start from 3 or above. I do not see the use of pin=RELAY_PIN. You can present the status of your relay's, that can create V_STATUS on MyController example: #define RELAY_SENSOR 3 // Relay sensor starts at 3 void presentation() { .... MyMessage relayMsg(RELAY_SENSOR, V_STATUS); for (int sensor=RELAY_SENSOR; sensor < (RELAY_SENSOR + NUMBER_OF_RELAYS); sensor++) { // Register all sensors to gw (they will be created as child devices) present(sensor, S_BINARY); relayMsg.sensor = sensor; send(relayMsg.set(loadState(sensor))); // current status of the relay } } NOTE: You have to update your relay code on setup and in receive too
serial, Ethernet to MQTT
MyController.org • mqtt ethernet serial mycontroller converter bridge • • jkandasa

5

1
Votes

5
Posts

43
Views

@Yveaux said in serial, Ethernet to MQTT: Of course, but MySensors MQTT gateway runs just as fine when connected over cabled ethernet, as when connected over wifi I do not know that Now on this tool, I do not see much benefit from ethernet to MQTT Still, it is good from serial to MQTT.

Connecting NodeMCU 1.0 Gateway to WiFi

Suggested Topics

One Arduino with multiple functions
Hardware • • A Former User

French Version
MyController.org • • JeeLet

Widgets météo
MyController.org • • JeeLet

Cannot add Nodes trough RS 485
MyController.org • • qobouky

serial, Ethernet to MQTT
MyController.org • mqtt ethernet serial mycontroller converter bridge • • jkandasa

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

Connecting NodeMCU 1.0 Gateway to WiFi

Suggested Topics

One Arduino with multiple functions Hardware • • A Former User

French Version MyController.org • • JeeLet

Widgets météo MyController.org • • JeeLet

Cannot add Nodes trough RS 485 MyController.org • • qobouky

serial, Ethernet to MQTT MyController.org • mqtt ethernet serial mycontroller converter bridge • • jkandasa

9Online

11.4kUsers

11.1kTopics

112.7kPosts

One Arduino with multiple functions
Hardware • • A Former User

French Version
MyController.org • • JeeLet

Widgets météo
MyController.org • • JeeLet

Cannot add Nodes trough RS 485
MyController.org • • qobouky

serial, Ethernet to MQTT
MyController.org • mqtt ethernet serial mycontroller converter bridge • • jkandasa

9
Online

11.4k
Users

11.1k
Topics

112.7k
Posts