RFM69 and Ethernet shield share SPI bus, each one with its own CS line. Ethernet shield uses pin 10 so JP1 should use pin 6 for the radio. Issues sharing SPI bus seems to be due to bad SEN line handling as described here. The official Arduino ethernet shield suffered from this, but most commonly used clones work ok. Shields including 74LVC14 as in the pic should work ok.

@kimot No, it is an obvious mistake, I am very sorry. Maybe it is becouse the code in master branch is very old, the newest is not yet on github, but the developement branch is quite new. I am going to fix this soon.

nevermind. now after all upgrades AND BATTERY CHANGE to sensebender it's all fine

@atilla-y Orange Pi is a controller and not a gateway. If you are suggesting you want to use the 5v adapter to power both controller and gateway I can not answer you. It might work but in the same time it might be to weak or to much interference. Try! If you get alof of random freezes and/or bad network communication you might want to seperate them It might work - but using the nrf24l01+ amplified requiers some more juice than then pro mini/uno/nano can handle so I suggest using a power in with a good voltage regulator (that can provide high current) and then split of to each unit.

Hi @berkseo. Thanks for the suggestion, but could you describe in more detail? As for my TODO list, there is already a task to add 485 interface to the gateway. My latest device "xRoom" have this interface. ps/ Where have you gone? I have been working on "xRoom" shield. A small announce: Do you remember the discussion about multinode? So, it will be available soon))

thx for reply yes dragino HE works like yun I think. for linkit as the product seems new, there is a little bit less docs. but I will see, price was so interesting that it was too much tempting lol. I will tell you what I can get... for fun, I have not presented yet, but I have a board in progress for raildin : 8x relays + 8inputs for yun and I added ethernet connector+hub usb chip

Hi, sorry for the delay, I had just read your post and I could said "me too" But I solved the problem and it works for two years now. I explain my solution here, if the French don't afraid you. https://easydomoticz.com/forum/viewtopic.php?f=20&t=6497 I resume, a 7.5volts power supply, a passive injector, and a spécial home-made cable to bypass the RJ45 socket. The 7.5 v go to Vin-Gnd of the Nano to produce 5v wich is returned to the W5100. QED. Rpx.

I have created a topic in the forum before, with tcpdump examples. http://www.domoticz.com/forum/viewtopic.php?f=6&t=6112 But the problem is still there, hopefully soon fix.

@epierre said: Hello, have you contacted Itead support on this ? I bought one too but had no time to test it yet (In fact I was waiting for you No worries, @epierre . I put a test webserver on the iBoard to make sure it was working OK. I was able to browse an SD card over ethernet so I didn't want to bother their support people. I never heard from @nneeoo and just decided to go the hardware route. It seems to be working just fine. I recommend it. It's more stable than the serial gateway I was running.

@lafleur I abandoned it due to the fact that my Nano cannot fit it together with signing support.

RTF(T)roubleshoot-guide http://www.mysensors.org/build/debug

@bomber Did you find a way to use CC3000 as gateway?

If anyone is interested in trying out the implementation using UDP packets sent to the subnet broadcast address, check out my pull request https://github.com/mysensors/Arduino/pull/66 thozza created this issue in mysensors/Arduino closed Dynamic IP assignment using DHCP and dynamic controller discovery for Ethernet Gateway #66

@5546dug Yes I think you need 1.4.1 or latest. The messages you see (0;0;3;9...) are traffic in the wireless sensor network. My problem appeared again. The EthernetGateway responds to Ping but Vera plugin says: "Cannot send command - communications error" So perhaps increasing power could help, but how? Is adding capacitors enough?? Like for the radio there already is one..

Hello. i had a similar problem. I replaced the network switch And then the ping worked

I'm using an Uno with Ethernet shield with no problems (after overcoming some initial startup problems).

Sorry for the huge kick.. But I seem to have the same ethernet gateway as TS. His his wire diagram valid?

Yeah that does seem to be the case. But I have read that some were having success so I gave it a go anyways... I can't see me having much time for a while to give this another go, so i'll probably wait until i can roll back to UI5.