Node to Node Communication via Gatreway

[jkandasa]

@hek Thank you I did serial debug, I'm not clear about route (to) address
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/MySensor.cpp#L401

Node-1:
send: 1-1-0-0 s=255,c=0,t=18,pt=0,l=6,sg=0,st=ok:1.5 b1
send: 1-1-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
repeater started, id=1, parent=0, distance=1
send: 1-1-0-0 s=255,c=3,t=11,pt=0,l=16,sg=0,st=ok:LevelSensor
send: 1-1-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 1-1-0-0 s=1,c=0,t=15,pt=0,l=6,sg=0,st=ok:1.5 b1
send: 1-1-0-0 s=1,c=1,t=13,pt=2,l=2,sg=0,st=ok:0
send: 1-1-3-3 s=1,c=1,t=13,pt=2,l=2,sg=0,st=fail:0

above '3' is 'to' (route) address, I do not understand what is '3' and how it was calculated, I hope here 'to' should be a parent address, which is 0

Gateway:
0;0;3;0;9;gateway started, id=0, parent=0, distance=0
0;0;3;0;14;Gateway startup complete.
0;0;3;0;9;read: 1-1-0 s=255,c=0,t=18,pt=0,l=6,sg=0:1.5 b1
1;255;0;0;18;1.5 b1
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
1;255;3;0;6;0
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=11,pt=0,l=16,sg=0:LevelSensor

1;255;3;0;11;LevelSensor
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
1;255;3;0;12;1.0
0;0;3;0;9;read: 1-1-0 s=1,c=0,t=15,pt=0,l=6,sg=0:1.5 b1
1;1;0;0;15;1.5 b1
0;0;3;0;9;read: 1-1-0 s=1,c=1,t=13,pt=2,l=2,sg=0:0
1;1;1;0;13;0

0;0;3;0;9;read: 3-3-0 s=255,c=0,t=18,pt=0,l=6,sg=0:1.5 b1
3;255;0;0;18;1.5 b1
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
3;255;3;0;6;0
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=11,pt=0,l=19,sg=0:LevelIndicator
3;255;3;0;11;LevelIndicator
0;0;3;0;9;read: 3-3-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
3;255;3;0;12;1.0
0;0;3;0;9;read: 3-3-0 s=1,c=0,t=15,pt=0,l=6,sg=0:1.5 b1
3;1;0;0;15;1.5 b1

Node-2:
send: 3-3-0-0 s=255,c=0,t=18,pt=0,l=6,sg=0,st=ok:1.5 b1
send: 3-3-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
repeater started, id=3, parent=0, distance=1
send: 3-3-0-0 s=255,c=3,t=11,pt=0,l=19,sg=0,st=ok:LevelIndicator
send: 3-3-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 3-3-0-0 s=1,c=0,t=15,pt=0,l=6,sg=0,st=ok:1.5 b1
send: 3-3-1-1 s=1,c=1,t=13,pt=2,l=2,sg=0,st=fail:0

[hek]

What does your code look like on the sending node (1)?

[jkandasa]

#define NODE_ID (int8_t) 1
#define N_LEVEL_DISPLAY_ID (int8_t) 3
#define S_LEVEL_DISPLAY_ID (int8_t) 1

MySensor gw;
 gw.begin(incomingMessage, NODE_ID, true);
MyMessage levelDisplayBoard(S_LEVEL_DISPLAY_ID, V_DISTANCE);
levelDisplayBoard.setDestination(N_LEVEL_DISPLAY_ID);
int dist = getDistance();
gw.send(levelDisplayBoard.set(dist));

[hek]

I think node 1 has a corrupt routing table (it thinks node 3 is a child).

Try clearing eeprom and re-upload your sketch. Or disable repeater-mode on it.

[jkandasa]

How to print routing table in serial console?

[hek]

You have to read it from eeprom.
It starts at position: EEPROM_ROUTES_ADDRESS (defined in MySensors.h)

http://www.arduino.cc/en/Tutorial/EEPROMRead

[jkandasa]

@hek you are right! There was an entry for Node-2 in Node-1 routing table, As it has direct access to Node-2, was trying to send directly. I removed the entry and now it's going throw gateway. All node works well. Perfect!

I thing we have to add code to remove routing table entry dynamically if it face some N number of failures. It will make life easier for those who is shifting node from one location to another location often.

[FullMetal]

Hello,

Sorry to resort to an old topic ...
I am currently using mysensors RS485, and I would like to extend my installation with this protocol.
and I would like to make the nodes communicate with each other through the gateway.
But I can't do what I want ... help!
on my node 4, I have an input and 1 output, the input activates and deactivates the output. (here no worries).
On my node 5, I have an input to activate the output of node 4, so I can turn it off but not turn it on, and I don't see any frames towards the gateway

here is the code for my node 5:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 5                     // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED


// Enable this if RS485 is connected to a hardware serial port
//#define MY_RS485_HWSERIAL Serial1
//#include <MqttClient.h>
#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID 4
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_LIGHT);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  
}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("Button", "1.1");

  
  present(CHILD_ID, S_LIGHT);  
}


//  Check if digital input has changed and send in new value
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      msg.setDestination(4);
      send(msg.set(state?false:true), false);// Send new state and request ack back
  }
  oldValue = value;
}  

[rejoe2]

@FullMetal Imo, you have to specify all send-settings in one line, e.g. like this:

send(buttonMsg.setDestination(MY_SISTER_NODE_ID).setSensor(CHILD_ID_RESET).set( button[i] ? "1" : "0"));

[FullMetal]

@rejoe2
thank you for your return,
but I have the same problem, I manage to activate the relay of node 4 from node 5, but I cannot deactivate it. and when I act on node 5 the gateway does not receive frames since it calls node 4.
I think that node 4 should send the relay status to node 5 so that it knows whether it is activated or not.

[tekka]

@FullMetal Please post a full debug log of both nodes showing the observed behaviour.

[rejoe2]

@FullMetal Pls add also code from node 4.

In general:

• if you want also info from node 5 to be sent to your controller/gateway, you have to add a second (normal) send command.
• wrt. to how node 4 reacts on the messages, you may better use sth. like a toggle logic.

[FullMetal]

@tekka @rejoe2
Désolé de revenir si tard ..
J'ai modifié mon code sur mes nœuds, mais le résultat n'est toujours pas là!

Voici mes codes:

node 4:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 4                    // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED



#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_PIN  4  // Arduino Digital I/O pin number for relay 
#define BUTTON_PIN  3  // Arduino Digital I/O pin number for button 
#define CHILD_ID 1   // Id of the sensor child
#define SYSTER_ID 5
#define RELAY_ON 1
#define RELAY_OFF 0

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

MyMessage msg(CHILD_ID,V_LIGHT);
//MyMessage msgconf(CHILD_ID,V_VAR1);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);

  // Make sure relays are off when starting up
  digitalWrite(RELAY_PIN, RELAY_OFF);
  // Then set relay pins in output mode
  pinMode(RELAY_PIN, OUTPUT);   
      
  // Set relay to last known state (using eeprom storage) 
  state = loadState(CHILD_ID);
  digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay & Button", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_LIGHT);
}

/*
*  Example on how to asynchronously check for new messages from gw
*/
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), true); // Send new state and request ack back
      wait(100);
      send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), true);
  }
  oldValue = value;
} 
 
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }

  if (message.type == V_LIGHT) {
     // Change relay state
     state = message.getBool();
     digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(CHILD_ID, state);
       
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 

}

node 5:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 5                     // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED


// Enable this if RS485 is connected to a hardware serial port
//#define MY_RS485_HWSERIAL Serial1
//#include <MqttClient.h>
#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID 1
#define SYSTER_ID 4
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_LIGHT);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  
}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("Button", "1.1");

  
  present(CHILD_ID, S_LIGHT);  
}


//  Check if digital input has changed and send in new value
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), false);// Send new state and request ack back
      Serial.println("wait 1/10sec");
      wait(100);
      send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), false);
  }
  oldValue = value;
}  
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }

  if (message.type == V_LIGHT) {
     // Change relay state
     state = message.getBool();
     //digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(SYSTER_ID, state);
       
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 

}

From node 4, my output is activated and deactivated immediately, due to double sending

from node 5, I can activate or deactivate if I launch the command from node 4 before otherwise.

[tekka]

@FullMetal said in Node to Node Communication via Gatreway: Please upload the debug logs for further troubleshooting.

[FullMetal]

@tekka said in Node to Node Communication via Gatreway:

@FullMetal said in Node to Node Communication via Gatreway: Please upload the debug logs for further troubleshooting.

Sorry

Debug logs node 4
Press button node 4

08:16:01.668 -> 13555 TSF:MSG:SEND,4-4-0-0,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:16:01.701 -> 13582 TSF:MSG:READ,0-0-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:16:01.701 -> 13586 TSF:MSG:ECHO
08:16:01.701 -> This is an ack from gateway

08:16:01.701 -> Incoming change for sensor:1, New status: 0

08:16:01.800 -> 13678 TSF:MSG:SEND,4-4-5-5,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
08:16:01.800 -> 13684 TSF:RTE:N2N OK
08:16:01.800 -> 13703 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:1
08:16:01.833 -> 13708 TSF:MSG:ECHO
08:16:01.833 -> This is an ack from gateway

08:16:01.833 -> Incoming change for sensor:1, New status: 1

Press button node 5

08:21:01.371 -> 313012 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:21:01.371 -> Incoming change for sensor:1, New status: 0

second press node 5

08:21:06.238 -> 317865 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:21:06.238 -> Incoming change for sensor:1, New status: 0

Debug logs node 5
Press button node 4

08:23:59.955 -> 51752 TSF:MSG:READ,4-4-5,s=1,c=1,t=2,pt=1,l=1,sg=0:1
08:23:59.955 -> 51757 TSF:MSG:ECHO REQ
08:23:59.988 -> 51777 TSF:MSG:SEND,5-5-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
08:23:59.988 -> 51783 TSF:RTE:N2N OK
08:23:59.988 -> Incoming change for sensor:1, New status: 1

Press button node 5

08:24:36.929 -> 88704 TSF:MSG:SEND,5-5-0-0,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:24:36.929 -> wait 1/10sec

08:24:37.062 -> 88827 TSF:MSG:SEND,5-5-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:24:37.062 -> 88834 TSF:RTE:N2N OK

Debug logs gateway
Press button node 4 and node 5

08:26:19.261 -> 0;255;3;0;9;79078 TSF:MSG:READ,4-4-0,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:26:19.261 -> 0;255;3;0;9;79084 TSF:MSG:ACK REQ
08:26:19.294 -> 0;255;3;0;9;79105 TSF:MSG:SEND,0-0-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:26:19.294 -> 4;1;1;0;2;0
08:26:20.321 -> 0;255;3;0;9;80116 TSF:MSG:READ,5-5-0,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:26:20.321 -> 5;1;1;0;2;0

[FullMetal]

@tekka @rejoe2
I just found!

ask the gateway not to send back acq
send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), false); // Send new state and request ack back
wait(100);
send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), true);

[rejoe2]

Good to her you found that point :smile:.
Imo you'd better change also your receive functions to not react on "ack" messages (via "else" prior to message.type-comparison).