Node to Node Communication via Gatreway

hek

I think node 1 has a corrupt routing table (it thinks node 3 is a child).

Try clearing eeprom and re-upload your sketch. Or disable repeater-mode on it.

jkandasa

How to print routing table in serial console?

hek

You have to read it from eeprom.
It starts at position: EEPROM_ROUTES_ADDRESS (defined in MySensors.h)

http://www.arduino.cc/en/Tutorial/EEPROMRead

jkandasa

@hek you are right! There was an entry for Node-2 in Node-1 routing table, As it has direct access to Node-2, was trying to send directly. I removed the entry and now it's going throw gateway. All node works well. Perfect!

I thing we have to add code to remove routing table entry dynamically if it face some N number of failures. It will make life easier for those who is shifting node from one location to another location often.

FullMetal

Hello,

Sorry to resort to an old topic ...
I am currently using mysensors RS485, and I would like to extend my installation with this protocol.
and I would like to make the nodes communicate with each other through the gateway.
But I can't do what I want ... help!
on my node 4, I have an input and 1 output, the input activates and deactivates the output. (here no worries).
On my node 5, I have an input to activate the output of node 4, so I can turn it off but not turn it on, and I don't see any frames towards the gateway

here is the code for my node 5:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 5                     // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED


// Enable this if RS485 is connected to a hardware serial port
//#define MY_RS485_HWSERIAL Serial1
//#include <MqttClient.h>
#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID 4
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_LIGHT);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  
}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("Button", "1.1");

  
  present(CHILD_ID, S_LIGHT);  
}


//  Check if digital input has changed and send in new value
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      msg.setDestination(4);
      send(msg.set(state?false:true), false);// Send new state and request ack back
  }
  oldValue = value;
}

rejoe2

@FullMetal Imo, you have to specify all send-settings in one line, e.g. like this:

send(buttonMsg.setDestination(MY_SISTER_NODE_ID).setSensor(CHILD_ID_RESET).set( button[i] ? "1" : "0"));

FullMetal

@rejoe2
thank you for your return,
but I have the same problem, I manage to activate the relay of node 4 from node 5, but I cannot deactivate it. and when I act on node 5 the gateway does not receive frames since it calls node 4.
I think that node 4 should send the relay status to node 5 so that it knows whether it is activated or not.

tekka

@FullMetal Please post a full debug log of both nodes showing the observed behaviour.

rejoe2

@FullMetal Pls add also code from node 4.

In general:

if you want also info from node 5 to be sent to your controller/gateway, you have to add a second (normal) send command.
wrt. to how node 4 reacts on the messages, you may better use sth. like a toggle logic.

FullMetal

@tekka @rejoe2
Désolé de revenir si tard ..
J'ai modifié mon code sur mes nœuds, mais le résultat n'est toujours pas là!

Voici mes codes:

node 4:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 4                    // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED



#include <MySensors.h>
#include <Bounce2.h>

#define RELAY_PIN  4  // Arduino Digital I/O pin number for relay 
#define BUTTON_PIN  3  // Arduino Digital I/O pin number for button 
#define CHILD_ID 1   // Id of the sensor child
#define SYSTER_ID 5
#define RELAY_ON 1
#define RELAY_OFF 0

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

MyMessage msg(CHILD_ID,V_LIGHT);
//MyMessage msgconf(CHILD_ID,V_VAR1);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);

  // Make sure relays are off when starting up
  digitalWrite(RELAY_PIN, RELAY_OFF);
  // Then set relay pins in output mode
  pinMode(RELAY_PIN, OUTPUT);   
      
  // Set relay to last known state (using eeprom storage) 
  state = loadState(CHILD_ID);
  digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Relay & Button", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_LIGHT);
}

/*
*  Example on how to asynchronously check for new messages from gw
*/
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), true); // Send new state and request ack back
      wait(100);
      send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), true);
  }
  oldValue = value;
} 
 
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }

  if (message.type == V_LIGHT) {
     // Change relay state
     state = message.getBool();
     digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(CHILD_ID, state);
       
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 

}

node 5:

// MySensors 
#define MY_PARENT_NODE_ID 0                   // define if fixed parent
#define MY_PARENT_NODE_IS_STATIC
#undef MY_REGISTRATION_FEATURE                  // sketch moves on if no registration
#define MY_NODE_ID 5                     // fixed node number

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable RS485 transport layer
#define MY_RS485

// Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2

// Set RS485 baud rate to use
#define MY_RS485_BAUD_RATE 9600

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  5  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  6  // the PCB, on board LED


// Enable this if RS485 is connected to a hardware serial port
//#define MY_RS485_HWSERIAL Serial1
//#include <MqttClient.h>
#include <SPI.h>
#include <MySensors.h>
#include <Bounce2.h>

#define CHILD_ID 1
#define SYSTER_ID 4
#define BUTTON_PIN  3  // Arduino Digital I/O pin for button/reed switch

Bounce debouncer = Bounce(); 
int oldValue=0;
bool state;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(CHILD_ID,V_LIGHT);

void setup()  
{  
  // Setup the button
  pinMode(BUTTON_PIN,INPUT_PULLUP);
  // Activate internal pull-up
  //digitalWrite(BUTTON_PIN,HIGH);
  
  // After setting up the button, setup debouncer
  debouncer.attach(BUTTON_PIN);
  debouncer.interval(5);
  
}

void presentation() {
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sendSketchInfo("Button", "1.1");

  
  present(CHILD_ID, S_LIGHT);  
}


//  Check if digital input has changed and send in new value
void loop() 
{
  debouncer.update();
  // Get the update value
  int value = debouncer.read();
  if (value != oldValue && value==0) {
      send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), false);// Send new state and request ack back
      Serial.println("wait 1/10sec");
      wait(100);
      send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), false);
  }
  oldValue = value;
}  
void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }

  if (message.type == V_LIGHT) {
     // Change relay state
     state = message.getBool();
     //digitalWrite(RELAY_PIN, state?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(SYSTER_ID, state);
       
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 

}

From node 4, my output is activated and deactivated immediately, due to double sending

from node 5, I can activate or deactivate if I launch the command from node 4 before otherwise.

tekka

@FullMetal said in Node to Node Communication via Gatreway: Please upload the debug logs for further troubleshooting.

FullMetal

@tekka said in Node to Node Communication via Gatreway:

@FullMetal said in Node to Node Communication via Gatreway: Please upload the debug logs for further troubleshooting.

Sorry

Debug logs node 4
Press button node 4

08:16:01.668 -> 13555 TSF:MSG:SEND,4-4-0-0,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:16:01.701 -> 13582 TSF:MSG:READ,0-0-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:16:01.701 -> 13586 TSF:MSG:ECHO
08:16:01.701 -> This is an ack from gateway

08:16:01.701 -> Incoming change for sensor:1, New status: 0

08:16:01.800 -> 13678 TSF:MSG:SEND,4-4-5-5,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
08:16:01.800 -> 13684 TSF:RTE:N2N OK
08:16:01.800 -> 13703 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:1
08:16:01.833 -> 13708 TSF:MSG:ECHO
08:16:01.833 -> This is an ack from gateway

08:16:01.833 -> Incoming change for sensor:1, New status: 1

Press button node 5

08:21:01.371 -> 313012 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:21:01.371 -> Incoming change for sensor:1, New status: 0

second press node 5

08:21:06.238 -> 317865 TSF:MSG:READ,5-5-4,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:21:06.238 -> Incoming change for sensor:1, New status: 0

Debug logs node 5
Press button node 4

08:23:59.955 -> 51752 TSF:MSG:READ,4-4-5,s=1,c=1,t=2,pt=1,l=1,sg=0:1
08:23:59.955 -> 51757 TSF:MSG:ECHO REQ
08:23:59.988 -> 51777 TSF:MSG:SEND,5-5-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:1
08:23:59.988 -> 51783 TSF:RTE:N2N OK
08:23:59.988 -> Incoming change for sensor:1, New status: 1

Press button node 5

08:24:36.929 -> 88704 TSF:MSG:SEND,5-5-0-0,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:24:36.929 -> wait 1/10sec

08:24:37.062 -> 88827 TSF:MSG:SEND,5-5-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:24:37.062 -> 88834 TSF:RTE:N2N OK

Debug logs gateway
Press button node 4 and node 5

08:26:19.261 -> 0;255;3;0;9;79078 TSF:MSG:READ,4-4-0,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:26:19.261 -> 0;255;3;0;9;79084 TSF:MSG:ACK REQ
08:26:19.294 -> 0;255;3;0;9;79105 TSF:MSG:SEND,0-0-4-4,s=1,c=1,t=2,pt=1,l=1,sg=0,ft=0,st=OK:0
08:26:19.294 -> 4;1;1;0;2;0
08:26:20.321 -> 0;255;3;0;9;80116 TSF:MSG:READ,5-5-0,s=1,c=1,t=2,pt=1,l=1,sg=0:0
08:26:20.321 -> 5;1;1;0;2;0

FullMetal

@tekka @rejoe2
I just found!

ask the gateway not to send back acq
send(msg.setDestination(MY_PARENT_NODE_ID).setSensor(CHILD_ID).set(state?false:true), false); // Send new state and request ack back
wait(100);
send(msg.setDestination(SYSTER_ID).setSensor(CHILD_ID).set(state?false:true), true);

rejoe2

Good to her you found that point :smile:.
Imo you'd better change also your receive functions to not react on "ack" messages (via "else" prior to message.type-comparison).

Node to Node Communication via Gatreway

22

12.0k

11.2k

113.4k