My Slim 2AA Battery Node

sundberg84

@m26872 - I made this (but with the big motiondec, because my small ones didnt work so well due to clone/copy). Thanks for PCB, instructions and tutorials. Great work!

Node is running at 13uA without motiondetector attached and 90-95uA with the motion dec attached. Im happy with that and ill see how long the batteries last. When my small motion dec arrive I can just switch over.

aneco

@sundberg84
The node on the breadboard is on the same desk and same distance to gateway. The same for my first sensor. And both are working well. Only issue with 4 sensors a soldered afterwords.

Just remember now that I used for the first sensor other solder. But do not think that this is causing the issue or .....

Eawo

Hello i wonder how you do then you put sensors outside mine stop work after a few hours i guess its becouse its cold here and maybe humitiy? then i take them inside for while it start working again. i think i need a waterprofe case or something

gohan

Well, batteries and components have working temperatures so it depends how cold it gets over there

Eawo

Its one in the garage it is never below 0- C this one was alive the longest the other one was dead in 2-3days and maybe as coldest it was 10- C. I'm starting to think it's something wrong with the gateway

gohan

If you reset either node or gateway, does it go back to work or what?

Eawo

No it doesn't only sometimes

gohan

If it was the gateway you should stop receiving data from other sensors too, right?

rollercontainer

@AWI said in My Slim 2AA Battery Node:

@rollercontainer Your sleep looks good. Did you remove this piece of code?
// Activate internal pull-ups
	digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
	digitalWrite(SECONDARY_BUTTON_PIN, HIGH);
Take a look at this thread for a < 1 uA consumption...

Hmm, I noticed, that I have to disable the internal pullups. But instead of removing the lines, I set them to LOW. I will test it without the lines and come back. Thank you @AWI.

siod

Ok, just want to give you an update:

I have 3 sensors running in the moment, initially I planned to run a lot more, but I still have problems with freezing of the sensors. The Sensors ran 2 months now until they were not coummunicating anymore, 1 is still working. I restarted 1 of the freezed sensors and it just came back up and works fine again, I leave the other one "freezed" just to see if it would come up again...

It´s sad that they are not very reliable but I don´t get what makes them freeze after working quiet good for such a long time (they are reporting every 15 minutes 24/7 and whenever a window is opened/closed).

I don´t think it´s a temp thing, also power should be no problem, batteries are still about 80 % loaded...

rollercontainer

Maybe there is something like a counter (variable++) which causes a overflow after two month?

siod

No, not really, but if you want to you can check my code:

// Sensor Node Schlafzimmer mit HTU21D Temp/Hum Sensor, Fensterkontakte an Interrupt PINS Digital 5&6. Sleep Time 15 Minutwn, wake up wenn Fenster geöffnet/geschlossen wird.
#define MY_RADIO_NRF24 //MySensor Library auf NRF24 Funkmodul einstellen, muss vor MySensor.h Initialisierung geschehen
// Define Node ID
#define MY_NODE_ID 1
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC

//Batterysensor
int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
int oldBatteryPcnt = 0;
#define CHILD_ID_BATT 7

//Kontaktschalter
//#include <Bounce2.h>
#define CHILD1_ID 1 // Kontaktschalter 1
#define CHILD2_ID 2 // Kontaktschalter 2
#define BUTTON1_PIN  2  // Kontaktschalter 1
#define BUTTON2_PIN  3  // Kontaktschalter 2
int oldValueReed1=-1;
int oldValueReed2=-1;

//Tempsensor
#include <SparkFunHTU21D.h>
#include <Wire.h>
#define CHILD_ID_HUM 3
#define CHILD_ID_TEMP 4
unsigned long SLEEP_TIME = 900000; // Sleep time between reads (in milliseconds)

#include <MySensors.h>
#include <SPI.h>

//tempsensor
HTU21D myHumidity;
float lastTemp;
float lastHum;
//boolean metric = true; 

//Messages
//Battery
MyMessage msgbatt(CHILD_ID_BATT,V_VOLTAGE);
// Kontaktschalter
MyMessage msgReed1(CHILD1_ID,V_TRIPPED); // Kontaktschalter 1
MyMessage msgReed2(CHILD2_ID,V_TRIPPED); // Kontaktschalter 2
//TempMessage
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);

//Presentation; present sensors to gateway!
void presentation(){
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Schlafzimmer Messstation", "2.0");
    
  // Register binary input sensor to gw (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  present(CHILD1_ID, S_DOOR); 
  present(CHILD2_ID, S_DOOR); 
    
  //Tempsensor
  present(CHILD_ID_HUM, S_HUM);
  present(CHILD_ID_TEMP, S_TEMP); 
  //metric = getConfig().isMetric;

  //Battery
  present(CHILD_ID_BATT,V_VOLTAGE);
}

//Setup
void setup()  
{  
  //Serial.begin(9600);
  Serial.println("Hello!");
  //Batterysensor
     // use the 1.1 V internal reference
#if defined(__AVR_ATmega2560__)
   analogReference(INTERNAL1V1);
#else
   analogReference(INTERNAL);
#endif

//Tempsensor
  Serial.println("Setting up TempSensor...");
  myHumidity.begin();
  Serial.println("...done!");

// Setup Kontaktschalter 1
  pinMode(BUTTON1_PIN,INPUT);
    // Activate internal pull-up
  digitalWrite(BUTTON1_PIN,HIGH);
// Setup Kontaktschalter 2
  pinMode(BUTTON2_PIN,INPUT);
  // Activate internal pull-up
  digitalWrite(BUTTON2_PIN,HIGH);
}

//Starte den Loop
void loop() 
{
  //Batterysensor
  // get the battery Voltage
  delay(1000);
   int sensorValue = analogRead(BATTERY_SENSE_PIN);
   #ifdef DEBUG
   #endif
   
   // 1M, 470K divider across battery and using internal ADC ref of 1.1V
   // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
   // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
   // 3.44/1023 = Volts per bit = 0.003363075
   float batteryV  = sensorValue * 0.003363075;
   int batteryPcnt = sensorValue / 10;

   #ifdef DEBUG
   Serial.print("Battery Voltage: ");
   Serial.print(batteryV);
   Serial.println(" V");

   Serial.print("Battery percent: ");
   Serial.print(batteryPcnt);
   Serial.println(" %");
   #endif

   if (oldBatteryPcnt != batteryPcnt) {
     // Power up radio after sleep
     sendBatteryLevel(batteryPcnt);
     send(msgbatt.set(batteryPcnt));
     oldBatteryPcnt = batteryPcnt;
   }
   
  //Kontakstschalter 1
   // Short delay to allow buttons to properly settle
  wait(10);
  // Get the update value
  int valueReed1 = digitalRead(BUTTON1_PIN);
 
  if (valueReed1 != oldValueReed1) {
     // Send in the new value
     send(msgReed1.set(valueReed1==HIGH ? 1 : 0));
     Serial.println("Button 1 geschaltet");
     oldValueReed1 = valueReed1;
  }
  //Kontakstschalter 2
  // Get the update value
  int valueReed2 = digitalRead(BUTTON2_PIN);
 
  if (valueReed2 != oldValueReed2) {
     // Send in the new value
     send(msgReed2.set(valueReed2==HIGH ? 1 : 0));
     Serial.println("Button 2 geschaltet");
     oldValueReed2 = valueReed2;
  }
 
 //Tempsensor
Serial.println("Starte Messung...");
  
    float temp = myHumidity.readTemperature();

  if (isnan(temp)) {
      Serial.println("Failed reading temperature from DHT");
  } else if (temp != lastTemp) {
    lastTemp = temp;
    send(msgTemp.set(temp, 1));
    Serial.print("T: ");
    Serial.println(temp);
  }
  
 float humd = myHumidity.readHumidity();
  if (isnan(humd)) {
      Serial.println("Failed reading humidity from DHT");
  } else if (humd != lastHum) {
      lastHum = humd;
      send(msgHum.set(humd, 1));
      Serial.print("H: ");
      Serial.println(humd);
  }

 Serial.println("Sleep...");
 sleep(BUTTON1_PIN - 2, CHANGE, BUTTON2_PIN - 2, CHANGE, SLEEP_TIME); //sleep a bit 
  
}

Tim Abels

@AWI: I am down to 1,3 µA :+1:

my code:

//#define MY_DEBUG
#define MY_RADIO_NRF24
#define MY_NODE_ID 66
#define MY_PARENT_NODE_ID 0
#define MY_PARENT_NODE_IS_STATIC

#include <MySensors.h>
#include "Vcc.h"

#define SKETCH_NAME "MySlim2aaBatteryNode"

#define PRIMARY_CHILD_ID 3
#define PRIMARY_BUTTON_PIN 3

MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);

const float VccMin   = 1.7;           // Minimum expected Vcc level, in Volts.
const float VccMax   = 3.3;           // Maximum expected Vcc level, in Volts.
const float VccCorrection = 3.496 / 3.572;  // Measured Vcc by multimeter divided by reported Vcc

const int32_t report_interval = 8640000; // 1day -> h * m * s * ms NOTICE: milliseconds, not microseconds!

Vcc vcc(VccCorrection);

#ifdef MY_DEBUG
void before(){
    Serial.begin(9600);
}
#endif

void setup()
{
    pinMode(PRIMARY_BUTTON_PIN, INPUT);
}

void presentation()
{
    sendSketchInfo(SKETCH_NAME, __DATE__);
    present(PRIMARY_CHILD_ID, S_DOOR, "Reed Contact");
}

void loop()
{
    int32_t timestamp = millis();

    uint8_t reedState;
    static uint8_t lastReedState = 2;
    static int32_t lastBatteryReport = -report_interval; // for inital report
    sleep(5); // Short delay to allow buttons to properly settle

    reedState = digitalRead(PRIMARY_BUTTON_PIN);

    if ( (timestamp-lastBatteryReport) >= report_interval ) {
      uint8_t batteryPercent = (uint8_t)vcc.Read_Perc(VccMin, VccMax);
      sendBatteryLevel(batteryPercent);
      lastBatteryReport = timestamp;
    }

    if (reedState != lastReedState) {
        // Value has changed from last transmission, send the updated reedState
        send(msg.set(reedState==HIGH));
        lastReedState = reedState;
    }

    sleep(PRIMARY_BUTTON_PIN-2, CHANGE, 0);
}

m26872

@siod
Gateway issue? Other sensors working or all down at same time? Do you have a sniffer or listen-only gateway, or heartbeat LED attached to each sensor?

What's the purpose of the delay(1000)? It usually safer to use wait() or sleep() and perhaps also to deal with the interrupt results first. You could also try level interrupt instead of "change". You're not using indefinite sleep so it shouldn't be a problem, but try anyway..

AWI

@Tim-Abels :+1: that is how you do it

Be aware that the timer (millis()) is not running during sleep.

m26872

@Tim-Abels
1.3uA is nice!
A question about your sketch: Is millis() working because it's an interrupt-only sleep() or have I missed something else? As I recall it millis() stops working when using sleep().
Edit: Haha. @AWI got it before me! :smile:

rollercontainer

@AWI one step forward, two steps back... Thanks for the hint.

I guess, I should send battery percentage every 10 interrupts or so. Even if the contact doesn't trigger for a while, I can force it by showing my neighbours my ocd on doors ^^ (knock, knock, knock - Penny!)

What do you think?

rollercontainer

Just noticed, that I use another login at home. So, the Tim-Abels is the rollercontainer... Sorry for that.

AWI

@rollercontainer alias @Tim-Abels ;-) Sounds good, although with 1.3uA the battery won't show much variation..

This is a similar on running on a coin cell (not calibrated). The voltage drop is caused mainly by the bad radio connection (many retries for sending > 10 mA)

0_1487319381911_upload-02a06ce9-126d-49f2-bbcb-dd01c3cea3d4

rollercontainer

Maybe its better to measure the voltage every 10 or 100 loops and only send one custom message/alert when its dropped below a threshold. I am using the MQTTClientGateway and Node-Red. In case of a battery-low message, node-red could send me an email with the node name. I will give it a try...

From https://www.mysensors.org/download/serial_api_20:

V_TEXT          47 	Text message to display on LCD or controller device 	S_INFO
V_CUSTOM 	48 	Custom messages used for controller/inter node specific commands, preferably using S_CUSTOM device type. 	S_CUSTOM```

My Slim 2AA Battery Node

18

11.7k

11.2k

113.1k