Step-by-step procedure to connect the NRF24L01+ to the GPIO pins and use the Raspberry as a Serial Gateway (MySensors 1.x)

[Oitzu]

Somehow the node thought it is node id 194 and a repeater...
I hacked in node id 0 and it worked. But it even works slower then the arduino serial gateway.

[mfalkvidd]

In http://forum.mysensors.org/topic/2305/nrf24l01-rpi2-direct-connection-problem/1 an user also got node id 194. Maybe the discussion there can help?

[jpbabou]

Hi
something is missing..

Is there a problem with the repository
Tks a lot for your job!

pi@domoticjp ~ $ sudo git clone https://github.com/mysensors/Raspberry.git
Cloning into 'Raspberry'...
remote: Counting objects: 273, done.
remote: Compressing objects: 100% (3/3), done.
remote: Total 273 (delta 0), reused 0 (delta 0), pack-reused 270
Receiving objects: 100% (273/273), 215.00 KiB | 0 bytes/s, done.
Resolving deltas: 100% (114/114), done.
Checking connectivity... done.
pi@domoticjp ~ $ cd Raspberry/librf24-bcm
-bash: cd: Raspberry/librf24-bcm: No such file or directory

[mfalkvidd]

Ah yes, the guide became invalid yesterday when a PR was merged. I'll update the guide, thanks for noticing.

Information about how to get the rf library is available in the readme in the Raspberry folder if you want to get going.

[msantang]

I got it working on my rb2 but i got 100% of cpu ussage.

I read a lot of post about this but i cant found a solution.

Some one know how to fix this?

[alexsh1]

@jpbabou said:

Hi
something is missing..

Is there a problem with the repository
Tks a lot for your job!

pi@domoticjp ~ $ sudo git clone https://github.com/mysensors/Raspberry.git
Cloning into 'Raspberry'...
remote: Counting objects: 273, done.
remote: Compressing objects: 100% (3/3), done.
remote: Total 273 (delta 0), reused 0 (delta 0), pack-reused 270
Receiving objects: 100% (273/273), 215.00 KiB | 0 bytes/s, done.
Resolving deltas: 100% (114/114), done.
Checking connectivity... done.
pi@domoticjp ~ $ cd Raspberry/librf24-bcm
-bash: cd: Raspberry/librf24-bcm: No such file or directory

Please go ahead and install the rf24 library from https://github.com/TMRh20/RF24
The rest should be the same

[Oitzu]

@msantang said:

I got it working on my rb2 but i got 100% of cpu ussage.

I read a lot of post about this but i cant found a solution.

Some one know how to fix this?

The 100% cpu usage is probably due to the style of receiving new messages from rf24/serial port.
The current state is that the PiSerialGateway tries to poll data in a endless loop from rf24/serial.
This could maybe fixed with using the interrupt of the nrf24l01+ to signal new data and reading data from the serial in blocking mode.
I want to solve this but using interrupts on the RPi isn't that trivial.

[mfalkvidd]

http://forum.mysensors.org/topic/2367/pigatewayserial-using-interrupts/2 has information on how to use interrupts. I haven't tried it myself though.

[Oitzu]

@mfalkvidd said:

http://forum.mysensors.org/topic/2367/pigatewayserial-using-interrupts/2 has information on how to use interrupts. I haven't tried it myself though.

Oh yeah, thanks for the hint @Bens got the exact same problem and seem to solved the rf24 part already. I hope he gets back online and shares his results. :)

[den2k]

Hi all,
I'm following this thread and have upgraded to MySensors v1.5 and get the following error. Version mismatch.

It looks like the Protocol version is 1.4.

Does the Raspberry MySensors Gateway support v1.5 or only v1.4? Any ideas on how to fix?

[alexsh1]

@den2k said:

Hi all,
I'm following this thread and have upgraded to MySensors v1.5 and get the following error. Version mismatch.

It looks like the Protocol version is 1.4.

Does the Raspberry MySensors Gateway support v1.5 or only v1.4? Any ideas on how to fix?

Up until now, MySensors v1.4 only for nrf24l01+ direct connection.
Did you upgrade the GW or the sensors or both ?

[hek]

Protocol version hasn't changed since 1.4
https://github.com/mysensors/Raspberry/blob/master/MyMessage.h#L41

So you must have some other problem.. As you can see you only get zeroes in the log...

[GertSanders]

You can "fake" a later version (e.g, 1.5) on the Raspberry by changing the version code in the version.h file and recompiling the Gateway software.

As far as I understand, the gateway will still pass the messages to the controller, even is there is a version mismatch message on the console.

[den2k]

@alexsh1 I know the sensors are on v1.5. As for the Raspberry Gateway, it looks like based on the info here, that is running v1.4.

[den2k]

@hek I'm running a custom 1Mhz build bootloader on a Pro Mini for the Sensor side. This was paired with the standard Serial Gateway running on another Pro Mini with v1.5 on both gateway and sensor. That setup was working. But I moved over to using the Pi gatway+nRF24+ radio and have this issue. I don't believe the hookup is the problem. I've seen the 0 readings before, and that usually meant node side issue or uninitiated Gateway. I have not changed the Node, so it must be the Pi gateway that is the problem. Any thoughts on what to test?

[den2k]

Noob question. Any one have an idea on solving the "Permission denied" error.

[den2k]

Solved my own problem. Using the following command did the trick.

sudo chown -h pi:pi ttyUSB20

[den2k]

weird. Permission Denied problem again.

What is the USER : GROUP that is needed for this to work?

[mfalkvidd]

@den2k I think your best chance is to post in the Home Assistant category. I don't have any experience with Home Assistant unfortunately.

[mfalkvidd]

@jpbabou said:

Hi
something is missing..

Is there a problem with the repository
Tks a lot for your job!

pi@domoticjp ~ $ sudo git clone https://github.com/mysensors/Raspberry.git
Cloning into 'Raspberry'...
remote: Counting objects: 273, done.
remote: Compressing objects: 100% (3/3), done.
remote: Total 273 (delta 0), reused 0 (delta 0), pack-reused 270
Receiving objects: 100% (273/273), 215.00 KiB | 0 bytes/s, done.
Resolving deltas: 100% (114/114), done.
Checking connectivity... done.
pi@domoticjp ~ $ cd Raspberry/librf24-bcm
-bash: cd: Raspberry/librf24-bcm: No such file or directory

The guide has been updated to reflect the updated in the MySensors Raspberry repository now. Thanks @jpbabou !