💬 Sensebender Micro
-
For the battery powering voltage measuring do you mean that this is not needed after all? (https://www.mysensors.org/build/battery#measuring-and-reporting-battery-level)
It would be just a matter of enabling the flag "#define BATT_SENSOR 199 " and no resistors needed? -
Sorry for the dummy question, but my SenseBender Micros came with a small white sticker on top of the Si7021 sensor (like in the pictures above). Is it supposed to be removed or to stay like that?
-
Hello!
Help me understand why the sketches are not loaded in Sensebender Micro - there is a synchronization error:
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x82
....
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x82
avrdude: stk500_recv(): programmer is not responding-
FTDI connected via 3.3V jumper
-
Another device built on the SB Micro with SB bootloader is also not flashed with the same error, but on the PC of my friend, sketches successfully loaded into the device and on my PC are given the correct data when working sketch
-
device and serial port are selected correctly
-
mySensors Lib and device packs(AVR, SAMD) installed with standard lib and device managers(and also added path https://raw.githubusercontent.com/mysensors/ArduinoBoards/master/package_mysensors.org_index.json in the settings menu)
-
at the same time if I take a pure Pro Mini and load into it any sample sketch of mySensors package - it will successfully do it and will work.
What am I doing wrong and how do I get the Sensebender Micro to take sketches?
-
-
Hello!
Help me understand why the sketches are not loaded in Sensebender Micro - there is a synchronization error:
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x82
....
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x82
avrdude: stk500_recv(): programmer is not responding-
FTDI connected via 3.3V jumper
-
Another device built on the SB Micro with SB bootloader is also not flashed with the same error, but on the PC of my friend, sketches successfully loaded into the device and on my PC are given the correct data when working sketch
-
device and serial port are selected correctly
-
mySensors Lib and device packs(AVR, SAMD) installed with standard lib and device managers(and also added path https://raw.githubusercontent.com/mysensors/ArduinoBoards/master/package_mysensors.org_index.json in the settings menu)
-
at the same time if I take a pure Pro Mini and load into it any sample sketch of mySensors package - it will successfully do it and will work.
What am I doing wrong and how do I get the Sensebender Micro to take sketches?
-
-
Did you select the sensebender micro as target in Arduino? Is it the same FTDI device that is used on both computers?
@tbowmo
Yes, of course, I chose the target device "Sensebender Micro -> "Atmega328p, 1mhz" and "Atmega328p, 8mhz"(for device (RGBW controller) based on SB Micro with 8Mhz quartz resonator).I tried three different FTDIs.
With any other Arduino (with native loaders) there are no problems with these FTDI adapters.
-
@tbowmo
Yes, of course, I chose the target device "Sensebender Micro -> "Atmega328p, 1mhz" and "Atmega328p, 8mhz"(for device (RGBW controller) based on SB Micro with 8Mhz quartz resonator).I tried three different FTDIs.
With any other Arduino (with native loaders) there are no problems with these FTDI adapters.
-
Hello,
Coming back to the battery powering topic: I was checking some SlimNode code and it uses #include <Vcc.h> library to report battery level. I can see in that the example code above doesn't use it. Does anyone know what is the difference? Which is better?
Thanks, -
Hi,
The slimnode original thread has a few (not sure anymore which example I'm using now because the thread is huge and I've lost track of it)
Here is one example:
https://forum.mysensors.org/topic/2067/my-slim-2aa-battery-node/306and other:
https://forum.mysensors.org/topic/2067/my-slim-2aa-battery-node/116 -
Unless the bootloader is reprogrammed, then it defaults to 8mhz, and you have to actively set registers to run at 1mhz in your sketch.
Do you have a ISP programmer? If yes, could you make a memory dump, and send it to me?
@tbowmo
I apologize for the delay in replying, I was very busy with work.It turned out to be some mystical incompatibility of the FTDI and Sensbender Micro or a device based on its loader. Three versions of my FTDI refused to work with Sensbender Micro, but they worked with regular Arduino, and the fourth one, bought on AliExpress, works perfectly normal. Externally, all the same, only those that do not work with Sensbender Micro, the labeling of the chip differs slightly in the quality of engraving on the plastic.
Maybe it's fake or some kind of non-standard chips.
-
@tbowmo
I apologize for the delay in replying, I was very busy with work.It turned out to be some mystical incompatibility of the FTDI and Sensbender Micro or a device based on its loader. Three versions of my FTDI refused to work with Sensbender Micro, but they worked with regular Arduino, and the fourth one, bought on AliExpress, works perfectly normal. Externally, all the same, only those that do not work with Sensbender Micro, the labeling of the chip differs slightly in the quality of engraving on the plastic.
Maybe it's fake or some kind of non-standard chips.
@nailman There are a lot of fake FTDI modules. Some are labelled FTDI other claim to be FTDI but are CH340. Some have DTR others RST and good ones like Adafruit Friend it is selectable.
My recommendation is do not try to save a few bucks here. Spend money on a good quality FTDI adapter like Adafruit Friend.
-
Hi,
I'm using the mysensor lib for a while but I recently run into problems. I've some arduino pro minis running with dht22 sensors which send their data over nrf24 to an mqtt ethernet gateway.
But maybe someone can help me with this one: I have build my own sensebender-micro modules. First of all I programmed the fuses of the mega328p as follows: lfuse: 0xE2, hfuse: 0xD2, efuse: 0xFE. Then I've programmed the DualOptiBoot Bootloader to them, everything worked fine so far, I can upoload sketches from the Arduino IDE via FTDI Programmer. The Problem: When I upload the official example sketch and watch the serial monitor I just see the MySensors splash screen. It seems, that the sketch does not even run into the setup routine. This starts to make me crazy, since I do not even know where to search. If I upload other sketches (basic blinking led, serial port examples or the passive node example from mysensors) it shows that my hardware in general seems to work. When I enable debug this is the output:__ __ ____ | \/ |_ _/ ___| ___ _ __ ___ ___ _ __ ___ | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __| | | | | |_| |___| | __/ | | \__ \ _ | | \__ \ |_| |_|\__, |____/ \___|_| |_|___/\___/|_| |___/ |___/ 2.3.0 16 MCO:BGN:INIT NODE,CP=RNONA---,VER=2.3.0 26 TSM:INIT 28 TSF:WUR:MS=0 36 TSM:INIT:TSP OK 38 TSF:SID:OK,ID=100 40 TSM:FPAR 75 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 2084 !TSM:FPAR:NO REPLY 2086 TSM:FPAR 2121 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 4130 !TSM:FPAR:NO REPLY 4132 TSM:FPAR 4167 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 6176 !TSM:FPAR:NO REPLY 6178 TSM:FPAR 6213 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 8222 !TSM:FPAR:FAIL 8224 TSM:FAIL:CNT=1 8226 TSM:FAIL:DIS 8228 TSF:TDI:TSL 18229 TSM:FAIL:RE-INIT 18231 TSM:INIT 18239 TSM:INIT:TSP OK 18241 TSF:SID:OK,ID=100 18243 TSM:FPAR 18280 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 20289 !TSM:FPAR:NO REPLYEven the NRF24 connection seems to work. This is the output of my mosquitto broker when running the passive node example:
home/OpenMQTTGateway/LWT Online home/OpenMQTTGateway/version 0.7 mygateway1-out/100/255/0/0/17 2.3.0 mygateway1-out/100/255/3/0/6 255 mygateway1-out/100/255/3/0/11 Passive node mygateway1-out/100/255/3/0/12 1.0 mygateway1-out/100/0/0/0/6 (null) mygateway1-out/100/0/1/0/0 25.70 mygateway1-out/100/0/1/0/0 26.90 mygateway1-out/100/0/1/0/0 27.30 mygateway1-out/100/0/1/0/0 25.80 mygateway1-out/100/0/1/0/0 26.00I appreciate any help, thanks in advance!
Cheers
-
Hi,
I'm using the mysensor lib for a while but I recently run into problems. I've some arduino pro minis running with dht22 sensors which send their data over nrf24 to an mqtt ethernet gateway.
But maybe someone can help me with this one: I have build my own sensebender-micro modules. First of all I programmed the fuses of the mega328p as follows: lfuse: 0xE2, hfuse: 0xD2, efuse: 0xFE. Then I've programmed the DualOptiBoot Bootloader to them, everything worked fine so far, I can upoload sketches from the Arduino IDE via FTDI Programmer. The Problem: When I upload the official example sketch and watch the serial monitor I just see the MySensors splash screen. It seems, that the sketch does not even run into the setup routine. This starts to make me crazy, since I do not even know where to search. If I upload other sketches (basic blinking led, serial port examples or the passive node example from mysensors) it shows that my hardware in general seems to work. When I enable debug this is the output:__ __ ____ | \/ |_ _/ ___| ___ _ __ ___ ___ _ __ ___ | |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __| | | | | |_| |___| | __/ | | \__ \ _ | | \__ \ |_| |_|\__, |____/ \___|_| |_|___/\___/|_| |___/ |___/ 2.3.0 16 MCO:BGN:INIT NODE,CP=RNONA---,VER=2.3.0 26 TSM:INIT 28 TSF:WUR:MS=0 36 TSM:INIT:TSP OK 38 TSF:SID:OK,ID=100 40 TSM:FPAR 75 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 2084 !TSM:FPAR:NO REPLY 2086 TSM:FPAR 2121 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 4130 !TSM:FPAR:NO REPLY 4132 TSM:FPAR 4167 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 6176 !TSM:FPAR:NO REPLY 6178 TSM:FPAR 6213 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 8222 !TSM:FPAR:FAIL 8224 TSM:FAIL:CNT=1 8226 TSM:FAIL:DIS 8228 TSF:TDI:TSL 18229 TSM:FAIL:RE-INIT 18231 TSM:INIT 18239 TSM:INIT:TSP OK 18241 TSF:SID:OK,ID=100 18243 TSM:FPAR 18280 TSF:MSG:SEND,100-100-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK: 20289 !TSM:FPAR:NO REPLYEven the NRF24 connection seems to work. This is the output of my mosquitto broker when running the passive node example:
home/OpenMQTTGateway/LWT Online home/OpenMQTTGateway/version 0.7 mygateway1-out/100/255/0/0/17 2.3.0 mygateway1-out/100/255/3/0/6 255 mygateway1-out/100/255/3/0/11 Passive node mygateway1-out/100/255/3/0/12 1.0 mygateway1-out/100/0/0/0/6 (null) mygateway1-out/100/0/1/0/0 25.70 mygateway1-out/100/0/1/0/0 26.90 mygateway1-out/100/0/1/0/0 27.30 mygateway1-out/100/0/1/0/0 25.80 mygateway1-out/100/0/1/0/0 26.00I appreciate any help, thanks in advance!
Cheers
Hi @flybysun, welcome to the forum!
!TSM:FPAR:NO REPLY
means that the sensor node does not get a response from the gateway. What type of gateway are you using? Could you post the debug log from it?
If you haven't already, check https://forum.mysensors.org/topic/666/debug-faq-and-how-ask-for-help/ for the most common problems and how to troubleshoot them. (Hint: Power supply is the most common problem, the nrf24 is extremely picky)
-
Hi @mfalkvidd, thanks for the warm welcome!
So, tonight I'll give it another try. I soldered 1000uF above VCC and GND on both the sender and the gateway RF Links (that's all I could find here for now). Still got issues. Here are the logs from my gateway, when it starts up and receives values from my working sensor I had before:0 MCO:BGN:INIT GW,CP=RNNGA---,VER=2.3.0 3 TSM:INIT 4 TSF:WUR:MS=0 11 TSM:INIT:TSP OK 12 TSM:INIT:GW MODE 14 TSM:READY:ID=0,PAR=0,DIS=0 17 MCO:REG:NOT NEEDED 580 GWT:TPC:IP=192.168.0.222 1583 MCO:BGN:STP 1584 MCO:BGN:INIT OK,TSP=1 1587 GWT:TPC:IP=192.168.0.222 2589 GWT:RMQ:MQTT RECONNECT 2797 GWT:RMQ:MQTT CONNECTED 2800 GWT:TPS:TOPIC=mygateway1-out/0/255/0/0/18,MSG SENT 20587 TSF:MSG:READ,1-1-0,s=0,c=1,t=1,pt=7,l=5,sg=0:32.5 20592 GWT:TPS:TOPIC=mygateway1-out/1/0/1/0/1,MSG SENT 55353 TSF:MSG:READ,1-1-0,s=1,c=1,t=0,pt=7,l=5,sg=0:27.3 55358 GWT:TPS:TOPIC=mygateway1-out/1/1/1/0/0,MSG SENT 55364 TSF:MSG:READ,1-1-0,s=0,c=1,t=1,pt=7,l=5,sg=0:32.6 55369 GWT:TPS:TOPIC=mygateway1-out/1/0/1/0/1,MSG SENTThis looks okay I guess, now this happens when I activate my SenseBender Micro:
139854 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 139859 TSF:MSG:BC 139860 TSF:MSG:FPAR REQ,ID=3 139864 TSF:PNG:SEND,TO=0 139866 TSF:CKU:OK 139868 TSF:MSG:GWL OK 140512 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 141940 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 141945 TSF:MSG:BC 141947 TSF:MSG:FPAR REQ,ID=3 141949 TSF:CKU:OK,FCTRL 141952 TSF:MSG:GWL OK 142632 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 144021 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 144026 TSF:MSG:BC 144028 TSF:MSG:FPAR REQ,ID=3 144030 TSF:CKU:OK,FCTRL 144033 TSF:MSG:GWL OK 144746 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 146101 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 146106 TSF:MSG:BC 146108 TSF:MSG:FPAR REQ,ID=3 146111 TSF:CKU:OK,FCTRL 146113 TSF:MSG:GWL OK 146857 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0I filled this logs into the Log Parser and found out that the Gateway receives informations on the sensor node, but when it responses it does not get the ACK from the sensor node.
May I have a faulty NRF24? I just received a new batch from AliExpress and this my first try with them.
My gateway is an Arduino Uno Board with the Arduino Ethernet shield and on top of that equipped with the long range version of the NRF24 Board (the one with the antenna).
The SenseBender is equipped with the "normal" smt version as suggested. The sensor nodes which are working right now were equipped with the smd version of the nrf-board.I also found out that the initialization of the sensor and the gateway has a different Core initialization, different capabilities (CP). I looked through the API, but didn't find what CP=RNNGA or CP=RNONA stands for.
Any suggestions or ideas?
-
Hi @mfalkvidd, thanks for the warm welcome!
So, tonight I'll give it another try. I soldered 1000uF above VCC and GND on both the sender and the gateway RF Links (that's all I could find here for now). Still got issues. Here are the logs from my gateway, when it starts up and receives values from my working sensor I had before:0 MCO:BGN:INIT GW,CP=RNNGA---,VER=2.3.0 3 TSM:INIT 4 TSF:WUR:MS=0 11 TSM:INIT:TSP OK 12 TSM:INIT:GW MODE 14 TSM:READY:ID=0,PAR=0,DIS=0 17 MCO:REG:NOT NEEDED 580 GWT:TPC:IP=192.168.0.222 1583 MCO:BGN:STP 1584 MCO:BGN:INIT OK,TSP=1 1587 GWT:TPC:IP=192.168.0.222 2589 GWT:RMQ:MQTT RECONNECT 2797 GWT:RMQ:MQTT CONNECTED 2800 GWT:TPS:TOPIC=mygateway1-out/0/255/0/0/18,MSG SENT 20587 TSF:MSG:READ,1-1-0,s=0,c=1,t=1,pt=7,l=5,sg=0:32.5 20592 GWT:TPS:TOPIC=mygateway1-out/1/0/1/0/1,MSG SENT 55353 TSF:MSG:READ,1-1-0,s=1,c=1,t=0,pt=7,l=5,sg=0:27.3 55358 GWT:TPS:TOPIC=mygateway1-out/1/1/1/0/0,MSG SENT 55364 TSF:MSG:READ,1-1-0,s=0,c=1,t=1,pt=7,l=5,sg=0:32.6 55369 GWT:TPS:TOPIC=mygateway1-out/1/0/1/0/1,MSG SENTThis looks okay I guess, now this happens when I activate my SenseBender Micro:
139854 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 139859 TSF:MSG:BC 139860 TSF:MSG:FPAR REQ,ID=3 139864 TSF:PNG:SEND,TO=0 139866 TSF:CKU:OK 139868 TSF:MSG:GWL OK 140512 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 141940 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 141945 TSF:MSG:BC 141947 TSF:MSG:FPAR REQ,ID=3 141949 TSF:CKU:OK,FCTRL 141952 TSF:MSG:GWL OK 142632 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 144021 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 144026 TSF:MSG:BC 144028 TSF:MSG:FPAR REQ,ID=3 144030 TSF:CKU:OK,FCTRL 144033 TSF:MSG:GWL OK 144746 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0 146101 TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0: 146106 TSF:MSG:BC 146108 TSF:MSG:FPAR REQ,ID=3 146111 TSF:CKU:OK,FCTRL 146113 TSF:MSG:GWL OK 146857 !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0I filled this logs into the Log Parser and found out that the Gateway receives informations on the sensor node, but when it responses it does not get the ACK from the sensor node.
May I have a faulty NRF24? I just received a new batch from AliExpress and this my first try with them.
My gateway is an Arduino Uno Board with the Arduino Ethernet shield and on top of that equipped with the long range version of the NRF24 Board (the one with the antenna).
The SenseBender is equipped with the "normal" smt version as suggested. The sensor nodes which are working right now were equipped with the smd version of the nrf-board.I also found out that the initialization of the sensor and the gateway has a different Core initialization, different capabilities (CP). I looked through the API, but didn't find what CP=RNNGA or CP=RNONA stands for.
Any suggestions or ideas?
@flybysun information on capabilites is available at https://forum.mysensors.org/topic/7718/mysensors-capabilities-deciphering and https://www.mysensors.org/apidocs/group__MyCapabilities.html
