Weather station

[NBM]

Hi

Im trying to make an node with BMP085, DHT22 and LM393. Barometer, Temp/hum and light.

Can anyone help me to make the sketch work?

Do the barometer have to be connected to A4 and A5?

//Vejrstation - Temp, Fugt, Lux, Baro - V 1.0

#include <SPI.h>
#include <MySensor.h> 
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_BMP085.h>  

#define CHILD_ID_HUM 0
#define CHILD_ID_TEMP 1
#define HUMIDITY_SENSOR_DIGITAL_PIN 3


#define CHILD_ID_LIGHT 2
#define LIGHT_SENSOR_ANALOG_PIN 1

#define BARO_CHILD 2
#define TEMP_CHILD 3

//Temp

MySensor gw;
DHT dht;
float lastTemp;
float lastHum;
boolean metric = true; 
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);

float lastPressure = -1;
float lastTemp = -1;
int lastForecast = -1;

const int LAST_SAMPLES_COUNT = 5;
float lastPressureSamples[LAST_SAMPLES_COUNT];

// this CONVERSION_FACTOR is used to convert from Pa to kPa in forecast algorithm
// get kPa/h be dividing hPa by 10 
#define CONVERSION_FACTOR (1.0/10.0)

int minuteCount = 0;
bool firstRound = true;
// average value is used in forecast algorithm.
float pressureAvg;
// average after 2 hours is used as reference value for the next iteration.
float pressureAvg2;

float dP_dt;
boolean metric;
MyMessage tempMsg(TEMP_CHILD, V_TEMP);
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE);
MyMessage forecastMsg(BARO_CHILD, V_FORECAST);

unsigned long SLEEP_TIME = 900000;  // sleep time between reads (seconds * 1000 milliseconds)
int oldBatteryPcnt = 0;

MyMessage msg(CHILD_ID_LIGHT, V_LIGHT_LEVEL);
int lastLightLevel;

//Batteri

int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point

//Baro

const float ALTITUDE = 34.691; // <-- adapt this value to your own location's altitude.

const char *weather[] = { "stable", "sunny", "cloudy", "unstable", "thunderstorm", "unknown" };
enum FORECAST
{
	STABLE = 0,			// "Stable Weather Pattern"
	SUNNY = 1,			// "Slowly rising Good Weather", "Clear/Sunny "
	CLOUDY = 2,			// "Slowly falling L-Pressure ", "Cloudy/Rain "
	UNSTABLE = 3,		// "Quickly rising H-Press",     "Not Stable"
	THUNDERSTORM = 4,	// "Quickly falling L-Press",    "Thunderstorm"
	UNKNOWN = 5			// "Unknown (More Time needed)
};

Adafruit_BMP085 bmp = Adafruit_BMP085();      // Digital Pressure Sensor 

void setup()  
{
   // use the 1.1 V internal reference
#if defined(__AVR_ATmega2560__)
   analogReference(INTERNAL1V1);
#else
   analogReference(INTERNAL);
#endif
   gw.begin(incomingMessage, 9, true));

   // Send the sketch version information to the gateway and Controller
   gw.sendSketchInfo("Weather Station", "1.0");

   dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN); 


  // Register all sensors to gw (they will be created as child devices)
	gw.present(CHILD_ID_HUM, S_HUM);
	gw.present(CHILD_ID_TEMP, S_TEMP);
	gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);
	gw.present(BARO_CHILD, S_BARO);
	gw.present(TEMP_CHILD, S_TEMP);
  
  metric = gw.getConfig().isMetric;

}

void loop()
{
   // get the battery Voltage
   int sensorValue = analogRead(BATTERY_SENSE_PIN);
   #ifdef DEBUG
   Serial.println(sensorValue);
   #endif
   
   // 1M, 470K divider across battery and using internal ADC ref of 1.1V
   // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
   // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
   // 3.44/1023 = Volts per bit = 0.003363075
   float batteryV  = sensorValue * 0.003363075;
   int batteryPcnt = sensorValue / 10;

   #ifdef DEBUG
   Serial.print("Battery Voltage: ");
   Serial.print(batteryV);
   Serial.println(" V");

   Serial.print("Battery percent: ");
   Serial.print(batteryPcnt);
   Serial.println(" %");
   #endif

   if (oldBatteryPcnt != batteryPcnt) {
     // Power up radio after sleep
     gw.sendBatteryLevel(batteryPcnt);
     oldBatteryPcnt = batteryPcnt;
   }
   gw.sleep(SLEEP_TIME);

delay(dht.getMinimumSamplingPeriod());

  float temperature = dht.getTemperature();
  if (isnan(temperature)) {
      Serial.println("Failed reading temperature from DHT");
  } else if (temperature != lastTemp) {
    lastTemp = temperature;
    if (!metric) {
      temperature = dht.toFahrenheit(temperature);
    }
    gw.send(msgTemp.set(temperature, 1));
    Serial.print("T: ");
    Serial.println(temperature);
  }
  
  float humidity = dht.getHumidity();
  if (isnan(humidity)) {
      Serial.println("Failed reading humidity from DHT");
  } else if (humidity != lastHum) {
      lastHum = humidity;
      gw.send(msgHum.set(humidity, 1));
      Serial.print("H: ");
      Serial.println(humidity);
  }

  gw.sleep(SLEEP_TIME); //sleep a bit

int lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23; 
  Serial.println(lightLevel);
  if (lightLevel != lastLightLevel) {
      gw.send(msg.set(lightLevel));
      lastLightLevel = lightLevel;
  }

float pressure = bmp.readSealevelPressure(ALTITUDE) / 100.0;
	float temperature = bmp.readTemperature();

	if (!metric) 
	{
		// Convert to fahrenheit
		temperature = temperature * 9.0 / 5.0 + 32.0;
	}

	int forecast = sample(pressure);

	Serial.print("Temperature = ");
	Serial.print(temperature);
	Serial.println(metric ? " *C" : " *F");
	Serial.print("Pressure = ");
	Serial.print(pressure);
	Serial.println(" hPa");
	Serial.print("Forecast = ");
	Serial.println(weather[forecast]);


	if (temperature != lastTemp) 
	{
		gw.send(tempMsg.set(temperature, 1));
		lastTemp = temperature;
	}

	if (pressure != lastPressure) 
	{
		gw.send(pressureMsg.set(pressure, 0));
		lastPressure = pressure;
	}

	if (forecast != lastForecast)
	{
		gw.send(forecastMsg.set(weather[forecast]));
		lastForecast = forecast;
	}

	gw.sleep(SLEEP_TIME);
}

float getLastPressureSamplesAverage()
{
	float lastPressureSamplesAverage = 0;
	for (int i = 0; i < LAST_SAMPLES_COUNT; i++)
	{
		lastPressureSamplesAverage += lastPressureSamples[i];
	}
	lastPressureSamplesAverage /= LAST_SAMPLES_COUNT;

	return lastPressureSamplesAverage;
}



// Algorithm found here
// http://www.freescale.com/files/sensors/doc/app_note/AN3914.pdf
// Pressure in hPa -->  forecast done by calculating kPa/h
int sample(float pressure)
{
	// Calculate the average of the last n minutes.
	int index = minuteCount % LAST_SAMPLES_COUNT;
	lastPressureSamples[index] = pressure;

	minuteCount++;
	if (minuteCount > 185)
	{
		minuteCount = 6;
	}

	if (minuteCount == 5)
	{
		pressureAvg = getLastPressureSamplesAverage();
	}
	else if (minuteCount == 35)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) // first time initial 3 hour
		{
			dP_dt = change * 2; // note this is for t = 0.5hour
		}
		else
		{
			dP_dt = change / 1.5; // divide by 1.5 as this is the difference in time from 0 value.
		}
	}
	else if (minuteCount == 65)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) //first time initial 3 hour
		{
			dP_dt = change; //note this is for t = 1 hour
		}
		else
		{
			dP_dt = change / 2; //divide by 2 as this is the difference in time from 0 value
		}
	}
	else if (minuteCount == 95)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) // first time initial 3 hour
		{
			dP_dt = change / 1.5; // note this is for t = 1.5 hour
		}
		else
		{
			dP_dt = change / 2.5; // divide by 2.5 as this is the difference in time from 0 value
		}
	}
	else if (minuteCount == 125)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		pressureAvg2 = lastPressureAvg; // store for later use.
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) // first time initial 3 hour
		{
			dP_dt = change / 2; // note this is for t = 2 hour
		}
		else
		{
			dP_dt = change / 3; // divide by 3 as this is the difference in time from 0 value
		}
	}
	else if (minuteCount == 155)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) // first time initial 3 hour
		{
			dP_dt = change / 2.5; // note this is for t = 2.5 hour
		}
		else
		{
			dP_dt = change / 3.5; // divide by 3.5 as this is the difference in time from 0 value
		}
	}
	else if (minuteCount == 185)
	{
		float lastPressureAvg = getLastPressureSamplesAverage();
		float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
		if (firstRound) // first time initial 3 hour
		{
			dP_dt = change / 3; // note this is for t = 3 hour
		}
		else
		{
			dP_dt = change / 4; // divide by 4 as this is the difference in time from 0 value
		}
		pressureAvg = pressureAvg2; // Equating the pressure at 0 to the pressure at 2 hour after 3 hours have past.
		firstRound = false; // flag to let you know that this is on the past 3 hour mark. Initialized to 0 outside main loop.
	}

	int forecast = UNKNOWN;
	if (minuteCount < 35 && firstRound) //if time is less than 35 min on the first 3 hour interval.
	{
		forecast = UNKNOWN;
	}
	else if (dP_dt < (-0.25))
	{
		forecast = THUNDERSTORM;
	}
	else if (dP_dt > 0.25)
	{
		forecast = UNSTABLE;
	}
	else if ((dP_dt > (-0.25)) && (dP_dt < (-0.05)))
	{
		forecast = CLOUDY;
	}
	else if ((dP_dt > 0.05) && (dP_dt < 0.25))
	{
		forecast = SUNNY;
	}
	else if ((dP_dt >(-0.05)) && (dP_dt < 0.05))
	{
		forecast = STABLE;
	}
	else
	{
		forecast = UNKNOWN;
	}

	// uncomment when debugging
	//Serial.print(F("Forecast at minute "));
	//Serial.print(minuteCount);
	//Serial.print(F(" dP/dt = "));
	//Serial.print(dP_dt);
	//Serial.print(F("kPa/h --> "));
	//Serial.println(weather[forecast]);

	return forecast;

}

I get this error:

Arduino: 1.6.5 (Mac OS X), Board: "Arduino Pro or Pro Mini, ATmega328 (3.3V, 8 MHz)"

Vejrstation_v1.2:31: error: redefinition of 'float lastTemp'
Vejrstation_v1.2:24: error: 'float lastTemp' previously declared here
Vejrstation_v1.2:49: error: redefinition of 'boolean metric'
Vejrstation_v1.2:26: error: 'boolean metric' previously defined here
Vejrstation_v1.2.ino: In function 'void setup()':
Vejrstation_v1.2:89: error: 'incomingMessage' was not declared in this scope
Vejrstation_v1.2:89: error: expected ';' before ')' token
Vejrstation_v1.2.ino: In function 'void loop()':
Vejrstation_v1.2:175: error: redeclaration of 'float temperature'
Vejrstation_v1.2:142: error: 'float temperature' previously declared here
redefinition of 'float lastTemp'

  This report would have more information with
  "Show verbose output during compilation"
  enabled in File > Preferences.

[Heinz]

Wiring is shown here
http://www.mysensors.org/build/pressure

The child ids of BARO and LIGHT are both 2 in your sketch.

[Heinz]

The BMP085 and the DHT have both a temperature: lastTemp of both sketches collide!
Have a look at this sketch which is a merge of a BMP085 and a DHT
https://github.com/windkh/mysensors/blob/master/WeatherStationSensor/WeatherStationSensor.ino

[NBM]

@Heinz I know. But is it possible to use A2 and A3?

[Heinz]

@NBM said:

@Heinz I know. But is it possible to use A2 and A3?

I don't know.

[Heinz]

A function is missing in your case:

void incomingMessage(const MyMessage &message){}

[NBM]

@Heinz Thank you.

I have made this sketch without errors.

// DHT-Sensor
// BMP085 Sensor

#include <SPI.h>
#include <MySensor.h>
#include <Wire.h>
#include <Adafruit_BMP085_U.h>
#include <Adafruit_Sensor.h>
#include <DHT.h>  


const bool sendAlways = true;

const float SEALEVEL = 688; // Westendorf
const float SEALEVEL_PRESSURE = 1013.25;

// ----------------------------------------------------------------------------
#define CHILD_ID_HUM 2
#define CHILD_ID_TEMP 3
#define HUMIDITY_SENSOR_DIGITAL_PIN 3
#define CHILD_ID_LIGHT 1
#define LIGHT_SENSOR_ANALOG_PIN 1

DHT dht;
float lastTemp;
float lastHum;
boolean metric = true;
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);


// ----------------------------------------------------------------------------
#define BARO_CHILD 0
#define TEMP_CHILD 1

unsigned long SLEEP_TIME = 30000; // Sleep time between reads (in milliseconds)
unsigned long SLEEP_TIME1 = 30000; // 1 minute required for forecast algorithm
unsigned long SLEEP_TIME2 = 30000; // 1 minute required for forecast algorithm
unsigned long SLEEP_TIME3 = 900000;  // sleep time between reads (seconds * 1000 milliseconds)


Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(1);    // Digital Pressure Sensor 
MySensor gw;

MyMessage msg(CHILD_ID_LIGHT, V_LIGHT_LEVEL);
int lastLightLevel;
int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
int oldBatteryPcnt = 0;

/*
DP/Dt explanation
0 = "Stable Weather Pattern"
1 = "Slowly rising Good Weather", "Clear/Sunny "
2 = "Slowly falling L-Pressure ", "Cloudy/Rain "
3 = "Quickly rising H-Press",     "Not Stable"
4 = "Quickly falling L-Press",    "Thunderstorm"
5 = "Unknown (More Time needed)
*/

const char *weatherStrings[] = { "stable", "sunny", "cloudy", "unstable", "thunderstorm", "unknown" };
enum FORECAST
{
  STABLE = 0,     // Stable weather
  SUNNY = 1,      // Slowly rising HP stable good weather
  CLOUDY = 2,     // Slowly falling Low Pressure System, stable rainy weather
  UNSTABLE = 3,   // Quickly rising HP, not stable weather
  THUNDERSTORM = 4, // Quickly falling LP, Thunderstorm, not stable
  UNKNOWN = 5     // Unknown, more time needed
};

const char *situationStrings[] = { "very low", "low", "normal", "high", "very high" };
enum WEATHER_SITUATION
{
  VERY_LOW_PRESSURE = 0,    // Tiefdruck p>-7.5hPa
  LOW_PRESSURE = 1,     // Tiefdruck p>-2.5hPa
  NORMAL_PRESSURE = 2,    // Normal  p <+/-02.5hPa  
  HIGH_PRESSURE = 3,      // Hochdruck p>2.5hPa
  VERY_HIGH_PRESSURE = 4,   // Hochdruck p>7.5hPa
};

float lastPressure = -1;
float lastPressureTemp = -1;
int lastForecast = -1;
int lastSituation = NORMAL_PRESSURE;

const int LAST_SAMPLES_COUNT = 5;
float lastPressureSamples[LAST_SAMPLES_COUNT];

// get kPa/h be dividing hPa by 10 
#define CONVERSION_FACTOR (1.0/10.0)

int minuteCount = 0;
bool firstRound = true;

// average value is used in forecast algorithm.
float pressureAvg;
// average after 2 hours is used as reference value for the next iteration.
float pressureAvg2;
float dP_dt;

MyMessage tempMsg(TEMP_CHILD, V_TEMP);
MyMessage pressureMsg(BARO_CHILD, V_PRESSURE);
MyMessage forecastMsg(BARO_CHILD, V_FORECAST);
MyMessage situationMsg(BARO_CHILD, V_VAR1);
MyMessage forecastMsg2(BARO_CHILD, V_VAR2);

void displaySensorDetails(void)
{
  sensor_t sensor;
  bmp.getSensor(&sensor);
  Serial.println(F("------------------------------------"));
  Serial.print(F("Sensor:       ")); Serial.println(sensor.name);
  Serial.print(F("Driver Ver:   ")); Serial.println(sensor.version);
  Serial.print(F("Unique ID:    ")); Serial.println(sensor.sensor_id);
  Serial.print(F("Max Value:    ")); Serial.print(sensor.max_value); Serial.println(F(" hPa"));
  Serial.print(F("Min Value:    ")); Serial.print(sensor.min_value); Serial.println(F(" hPa"));
  Serial.print(F("Resolution:   ")); Serial.print(sensor.resolution); Serial.println(F(" hPa"));
  Serial.println(F("------------------------------------"));
  Serial.println(F(""));
  delay(500);
}

void initPressureSensor()
{
  if (!bmp.begin())
  {
    Serial.println(F("Could not find a valid BMP085 sensor, check wiring!"));
    while (1) {}
  }

  displaySensorDetails();
}

void initHumiditySensor()
{
  dht.setup(HUMIDITY_SENSOR_DIGITAL_PIN);
}

void setup() 
{
     // use the 1.1 V internal reference
  #if defined(__AVR_ATmega2560__)
   analogReference(INTERNAL1V1);
  #else
   analogReference(INTERNAL);
  #endif
  gw.begin();
  gw.sendSketchInfo("Weather Station Sensor", "2.1");

  initPressureSensor();
  initHumiditySensor();

  gw.present(BARO_CHILD, S_BARO);
  gw.present(TEMP_CHILD, S_TEMP);
  gw.present(CHILD_ID_HUM, S_HUM);
  gw.present(CHILD_ID_TEMP, S_TEMP);
  gw.present(CHILD_ID_LIGHT, S_LIGHT_LEVEL);

  metric = gw.getConfig().isMetric;

 int lightLevel = (1023-analogRead(LIGHT_SENSOR_ANALOG_PIN))/10.23; 
  Serial.println(lightLevel);
  if (lightLevel != lastLightLevel) {
      gw.send(msg.set(lightLevel));
      lastLightLevel = lightLevel;
  }
   gw.sleep(SLEEP_TIME);  
}

int getWeatherSituation(float pressure)
{
  int situation = NORMAL_PRESSURE;

  float delta = pressure - SEALEVEL_PRESSURE;
  if (delta > 7.5)
  {
    situation = VERY_HIGH_PRESSURE;
  }
  else if (delta > 2.5)
  {
    situation = HIGH_PRESSURE;
  }
  else if (delta < -7.5)
  {
    situation = VERY_LOW_PRESSURE;
  }
  else if (delta < -2.5)
  {
    situation = LOW_PRESSURE;
  }
  else
  {
    situation = NORMAL_PRESSURE;
  }

  return situation;
}

bool updatePressureSensor()
{
  bool changed = false;

  sensors_event_t event;
  bmp.getEvent(&event);

  if (event.pressure)
  {
    float absolutePressure = event.pressure;
    Serial.print(F("abs Pressure = "));
    Serial.print(absolutePressure);
    Serial.println(F(" hPa"));
    
    //float altitude = bmp.pressureToAltitude(SEALEVEL_PRESSURE, pressure);
    //Serial.print(F("Altitude = "));
    //Serial.print(altitude);
    //Serial.println(F(" m"));

    //sealevel pressure p0 from absolute pressure.
    float pressure = bmp.seaLevelForAltitude(SEALEVEL, absolutePressure);

    float pressureTemperature;
    bmp.getTemperature(&pressureTemperature);

    if (!metric) 
    {
      // Convert to fahrenheit
      pressureTemperature = pressureTemperature * 9.0 / 5.0 + 32.0;
    }

    int forecast = sample(pressure);
    int situation = getWeatherSituation(pressure);


    if (sendAlways || (pressureTemperature != lastPressureTemp))
    {
      changed = true;
      lastPressureTemp = pressureTemperature;
      Serial.print(F("Temperature = "));
      Serial.print(pressureTemperature);
      Serial.println(metric ? F(" *C") : F(" *F"));
      if (!gw.send(tempMsg.set(lastPressureTemp, 1)))
      {
        lastPressureTemp = -1.0;
      }
    }


    if (sendAlways || (pressure != lastPressure))
    {
      changed = true;
      lastPressure = pressure;
      Serial.print(F("sealevel Pressure = "));
      Serial.print(pressure);
      Serial.println(F(" hPa"));
      if (!gw.send(pressureMsg.set(lastPressure, 1)))
      {
        lastPressure = -1.0;
      }
    }


    if (sendAlways || (forecast != lastForecast))
    {
      changed = true;
      lastForecast = forecast;
      Serial.print(F("Forecast = "));
      Serial.println(weatherStrings[forecast]);
      if (gw.send(forecastMsg.set(weatherStrings[lastForecast])))
      {
        if (!gw.send(forecastMsg2.set(lastForecast)))
        {
        }
      }
      else
      {
        lastForecast = -1.0;
      }
    }


    if (sendAlways || (situation != lastSituation))
    {
      changed = true;
      lastSituation = situation;
      Serial.print(F("Situation = "));
      Serial.println(situationStrings[situation]);
      if (!gw.send(situationMsg.set(lastSituation, 0)))
      {
        lastSituation = -1.0;
      }
    }
  }

  return changed;
}

bool updateHumiditySensor()
{
  bool changed = false;

  float temperature = dht.getTemperature();
  float humidity = dht.getHumidity();

  if (!isnan(temperature))
  {
#ifdef SEND_WHEN_CHANGED
    if (temperature != lastTemp)
#endif
    {
      lastTemp = temperature;
      if (!metric)
      {
        temperature = dht.toFahrenheit(temperature);
      }
      changed = true;
      Serial.print(F("T: "));
      Serial.println(temperature);
      if (!gw.send(msgTemp.set(temperature, 1)))
      {
        lastTemp = -1.0;
      }
    }
  }
  else
  {
    Serial.println(F("Failed reading temperature from DHT"));
  }
  
  
  if (!isnan(humidity))
  {
#ifdef SEND_WHEN_CHANGED
    if (humidity != lastHum)
#endif
    {
      lastHum = humidity;
      changed = true;
      Serial.print(F("H: "));
      Serial.println(humidity);
      if (!gw.send(msgHum.set(lastHum, 1)))
      {
        lastHum = -1.0;
      }
    }
  }
  else
  {
    Serial.println(F("Failed reading humidity from DHT"));
  }
  
  return changed;
}

void loop() 
{
   // get the battery Voltage
   int sensorValue = analogRead(BATTERY_SENSE_PIN);
   #ifdef DEBUG
   Serial.println(sensorValue);
   #endif
   
   // 1M, 470K divider across battery and using internal ADC ref of 1.1V
   // Sense point is bypassed with 0.1 uF cap to reduce noise at that point
   // ((1e6+470e3)/470e3)*1.1 = Vmax = 3.44 Volts
   // 3.44/1023 = Volts per bit = 0.003363075
   float batteryV  = sensorValue * 0.003363075;
   int batteryPcnt = sensorValue / 10;

   #ifdef DEBUG
   Serial.print("Battery Voltage: ");
   Serial.print(batteryV);
   Serial.println(" V");

   Serial.print("Battery percent: ");
   Serial.print(batteryPcnt);
   Serial.println(" %");
   #endif

   if (oldBatteryPcnt != batteryPcnt) {
     // Power up radio after sleep
     gw.sendBatteryLevel(batteryPcnt);
     oldBatteryPcnt = batteryPcnt;
   }
  updatePressureSensor();
  gw.sleep(SLEEP_TIME1);
  updateHumiditySensor();
  gw.sleep(SLEEP_TIME2);

  gw.sleep(SLEEP_TIME3);
}


float getLastPressureSamplesAverage()
{
  float lastPressureSamplesAverage = 0;
  for (int i = 0; i < LAST_SAMPLES_COUNT; i++)
  {
    lastPressureSamplesAverage += lastPressureSamples[i];
  }
  lastPressureSamplesAverage /= LAST_SAMPLES_COUNT;

  //Serial.print(F("### 5min-Average:"));
  //Serial.print(lastPressureSamplesAverage);
  //Serial.println(F(" hPa"));

  return lastPressureSamplesAverage;
}



// Algorithm found here
// http://www.freescale.com/files/sensors/doc/app_note/AN3914.pdf
// Pressure in hPa -->  forecast done by calculating kPa/h
int sample(float pressure)
{
  // Calculate the average of the last n minutes.
  int index = minuteCount % LAST_SAMPLES_COUNT;
  lastPressureSamples[index] = pressure;

  minuteCount++;
  if (minuteCount > 185)
  {
    minuteCount = 6;
  }

  if (minuteCount == 5)
  {
    pressureAvg = getLastPressureSamplesAverage();
  }
  else if (minuteCount == 35)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) // first time initial 3 hour
    {
      dP_dt = change * 2; // note this is for t = 0.5hour
    }
    else
    {
      dP_dt = change / 1.5; // divide by 1.5 as this is the difference in time from 0 value.
    }
  }
  else if (minuteCount == 65)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) //first time initial 3 hour
    {
      dP_dt = change; //note this is for t = 1 hour
    }
    else
    {
      dP_dt = change / 2; //divide by 2 as this is the difference in time from 0 value
    }
  }
  else if (minuteCount == 95)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) // first time initial 3 hour
    {
      dP_dt = change / 1.5; // note this is for t = 1.5 hour
    }
    else
    {
      dP_dt = change / 2.5; // divide by 2.5 as this is the difference in time from 0 value
    }
  }
  else if (minuteCount == 125)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    pressureAvg2 = lastPressureAvg; // store for later use.
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) // first time initial 3 hour
    {
      dP_dt = change / 2; // note this is for t = 2 hour
    }
    else
    {
      dP_dt = change / 3; // divide by 3 as this is the difference in time from 0 value
    }
  }
  else if (minuteCount == 155)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) // first time initial 3 hour
    {
      dP_dt = change / 2.5; // note this is for t = 2.5 hour
    }
    else
    {
      dP_dt = change / 3.5; // divide by 3.5 as this is the difference in time from 0 value
    }
  }
  else if (minuteCount == 185)
  {
    float lastPressureAvg = getLastPressureSamplesAverage();
    float change = (lastPressureAvg - pressureAvg) * CONVERSION_FACTOR;
    if (firstRound) // first time initial 3 hour
    {
      dP_dt = change / 3; // note this is for t = 3 hour
    }
    else
    {
      dP_dt = change / 4; // divide by 4 as this is the difference in time from 0 value
    }
    pressureAvg = pressureAvg2; // Equating the pressure at 0 to the pressure at 2 hour after 3 hours have past.
    firstRound = false; // flag to let you know that this is on the past 3 hour mark. Initialized to 0 outside main loop.
  }

  int forecast = UNKNOWN;
  if (minuteCount < 35 && firstRound) //if time is less than 35 min on the first 3 hour interval.
  {
    forecast = UNKNOWN;
  }
  else if (dP_dt < (-0.25))
  {
    forecast = THUNDERSTORM;
  }
  else if (dP_dt > 0.25)
  {
    forecast = UNSTABLE;
  }
  else if ((dP_dt > (-0.25)) && (dP_dt < (-0.05)))
  {
    forecast = CLOUDY;
  }
  else if ((dP_dt > 0.05) && (dP_dt < 0.25))
  {
    forecast = SUNNY;
  }
  else if ((dP_dt >(-0.05)) && (dP_dt < 0.05))
  {
    forecast = STABLE;
  }
  else
  {
    forecast = UNKNOWN;
  }

  Serial.print(F("Forecast at minute "));
  Serial.print(minuteCount);
  Serial.print(F(" dP/dt = "));
  Serial.print(dP_dt);
  Serial.print(F("kPa/h --> "));  
  Serial.println(weatherStrings[forecast]);

  return forecast;
}```

[Dylano]

@Heinz

Is this sketch working great now?
And how is the battery?
How long can work this sketch, on what type battery?

[Heinz]

@Dylano the sketch in this thread is from @NBM, if you mean
https://github.com/windkh/mysensors/blob/master/WeatherStationSensor/WeatherStationSensor.ino
then this one is working very well.

This one is the official mysensors example
https://github.com/mysensors/Arduino/blob/development/libraries/MySensors/examples/WeatherStationSensor/WeatherStationSensor.ino

[Dylano]

still got an error:
C:\Users\DM_PC\Desktop\Mysensors 23-2-2015\Sketches Werkend\sketch_mar05a\sketch_mar05a.ino:8:29: fatal error: Adafruit_Sensor.h: No such file or directory

#include <Adafruit_Sensor.h>

Only where can i download the adafruit library?

[Heinz]

@Dylano

https://github.com/adafruit/Adafruit_Sensor
https://github.com/adafruit/Adafruit_BMP085_Unified

[Dylano]

@Heinz said:

@Dylano

https://github.com/adafruit/Adafruit_Sensor
https://github.com/adafruit/Adafruit_BMP085_Unified

Thanks!!!