💬 MySensor Dioder (Ikea)

mortommy

Delete the MySensors folder in libraries and download it again.

pentti12

Now I downloaded Arduino IDE 1.6.5.zip, then I extracted it into C:/tools folder. Then I deleted everything from the library folder. Then I started Arduino IDE and I added MySensors-1.5.4.zip library. IDE reported that this file does not contain valid library. I closed IDE. So I unzipped MySensors-1.5.4.zip library directly into library folder. Then I started again IDE and checked that IDE can see MySensors-1.5.4 library. I opened MySensorDioder_133.ino and tried to compile it.

Still got the following error:

MySensorDioder_133.ino:38:30: fatal error: MyTransportNRF24.h: No such file or directory
compilation terminated.

How to continue?

pentti12

Mortommy: Can you change your sketch so that it support MySensors 2.0 library?

mortommy

Hi @pentti12 ,
please find the sketch 2.0.0 in the project. I couldn't test it yet, I have converted it following the guidance and I just verified that it compiles successfully.

pentti12

Sorry, but the compiler found a missing library file:

MyTransportNRF24.h

MySensors library 2.0 has MyTransportNRF24.cpp only

pentti12

Hi

I changed my Arduino IDE 1.6.11 using the MySensors development library v2.1.0-beta. Now the compiling went OK. I will continue with that. It will take few days before I have more info about how things went with actual hardware.

pentti12

I tested this latest sketch in my actual hardware (Arduino Mega + Proto shield with additionla components + Ikea Dioder control board). I cannot get system working, nothing happens when I press UP, DOWN buttons. Led-lights stay ON after power up.
I also tested to compile your sketch with Arduino IDE and MySensors Library V2.0.0. Compiling went OK, no progress with actual hardware.

How can I test step by step what is happening during startup?

mortommy

@pentti12 ,
add the line

#define MY_DEBUG

at the begging of the sketch so via Serial Monitor you'll be able to see the messages pushed by the commands println. You can add other println commands in other point to see the steps covered.

pentti12

OK, I added the line and now I get:

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT

So I have to check my radio-module or replace it with new one. I will continue ...

mortommy

ok, something is definitely wrong with the radio module. Can you check the connection according to this page?

pentti12

I changed my Radio-module to new one. Does not help. So I have to check my wiring on prototype board.

pentti12

Wiring was OK, but 10uF elko is missing from the 3.3V supply. I have only 440nF capasitor at the moment. This seems to be too small value. I will have 10uF elko on next monday available. So project will take a break.

pentti12

I added 10uF capasitor between VCC and GND pins of the radio module. I also added #define MY_DEBUG_VERBOSE_RF24 line into sketch. I got the following response:

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
RF24:write register, reg=0, value=14
RF24:write register, reg=3, value=3
RF24:write register, reg=4, value=95
RF24:write register, reg=5, value=76
RF24:write register, reg=6, value=39
RF24:read register, reg=6, value=255
RF24:read register, reg=5, value=255
RF24:Sanity check failed: configuration mismatch! Check wiring, replace module or non-P version
!TSM:RADIO:FAIL
!TSM:FAILURE
TSM:PDT
RF24:write register, reg=0, value=12
RF24:power down

I have changed the radio module to new one without success. So there must be some other reason why this sketch does not work in my hardware. Any ideas?

mortommy

Which module are you using? if it is NRF24L01+ be sure it is the "plus" version.

pentti12

At least I have ordered nRF24L01+ versions. And I use them on other MySensors node and they are working OK.

pentti12

Update:

I changed Arduino Board from Arduino Mega R3 to Arduino UNO board. I placed my protoshield above UNO-board and now I got following response:

Starting sensor (RNNNA-, 2.0.0)
TSM:INIT
RF24:write register, reg=0, value=14
RF24:write register, reg=3, value=3
RF24:write register, reg=4, value=95
RF24:write register, reg=5, value=76
RF24:write register, reg=6, value=39
RF24:read register, reg=6, value=39
RF24:read register, reg=5, value=76
RF24:write register, reg=16, value=115
RF24:write register, reg=29, value=6
RF24:write register, reg=2, value=2
RF24:write register, reg=1, value=0
RF24:write register, reg=28, value=3
RF24:flushRX
RF24:flushTX
RF24:write register, reg=7, value=112
TSM:RADIO:OK
RF24:write register, reg=2, value=3
RF24:write register, reg=1, value=1
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:ASSIGNID:OK (ID=9)
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:MAX_RT
RF24:flushTX
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=255
RF24:write register, reg=10, value=255
RF24:write register, reg=16, value=255
RF24:send message to 255, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:MAX_RT
RF24:flushTX
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
RF24:read message, len=8
RF24:write register, reg=7, value=64
TSP:MSG:READ 0-0-9 s=255,c=3,t=8,pt=1,l=1,sg=0:0
TSP:MSG:FPAR RES (ID=0, dist=0)
TSP:MSG:PAR OK (ID=0, dist=1)
TSM:FPAR:OK
TSM:ID
TSM:CHKID:OK (ID=9)
TSM:UPL
TSP:PING:SEND (dest=0)
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=8
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
RF24:read message, len=8
RF24:write register, reg=7, value=64
TSP:MSG:READ 0-0-9 s=255,c=3,t=25,pt=1,l=1,sg=0:1
TSP:MSG:PONG RECV (hops=1)
TSP:CHKUPL:OK
TSM:UPL:OK
TSM:READY
Setup... end.
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=9
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=ok:0100
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=12
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=ok:2.0.0
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=8
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=ok:0
RF24:read message, len=9
RF24:write register, reg=7, value=64
TSP:MSG:READ 0-0-9 s=255,c=3,t=15,pt=6,l=2,sg=0:0100
Incoming message: 15
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=21
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=11,pt=0,l=14,sg=0,ft=0,st=ok:MySensorDioder
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=12
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=12,pt=0,l=5,sg=0,ft=0,st=ok:2.0.0
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=0,c=0,t=4,pt=0,l=0,sg=0,ft=0,st=ok:
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=7
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=1,c=0,t=26,pt=0,l=0,sg=0,ft=0,st=ok:
Request registration...
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=8
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=ok:2
RF24:read message, len=8
RF24:write register, reg=7, value=64
TSP:MSG:READ 0-0-9 s=255,c=3,t=27,pt=1,l=1,sg=0:1
Node registration=1
Init complete, id=9, parent=0, distance=1, registration=1
Wheel position changed.
Wheel position: 0
Hue value of the Wheel position: 0
Send command to lights.
Bright: 0
Red: 0
Green: 0
Blue: 0
RGB in HEX: 000000

RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=11
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=0,c=1,t=3,pt=4,l=4,sg=0,ft=0,st=ok:0
RF24:stop listening
RF24:write register, reg=0, value=14
RF24:open writing pipe, recipient=0
RF24:write register, reg=10, value=0
RF24:write register, reg=16, value=0
RF24:send message to 0, len=13
RF24:flushTX
RF24:write register, reg=7, value=48
RF24:start listening
RF24:write register, reg=0, value=15
RF24:write register, reg=10, value=9
TSP:MSG:SEND 9-9-0-0 s=1,c=1,t=40,pt=0,l=6,sg=0,ft=0,st=ok:000000

Now sketch seems to work. I will continue by adding IKEA DIODER Leds. More info later.

pentti12

Update:

I can control locally the IKEA DIODER now. So the hardware is more or less working as expected, but do you have good instructions how I can get OpenHAB2 and MySensors Ethernet Gateway working together. Today I can see MySensors Ethernet Gateway ONLINE state and I can manually add Custom Sensor as a thing, but I cannot control items via Openhab.

I use the latest OH2 Snapshot ( on Pine64 with Debian Jessie) and latest MySensors GatewayW5100 (library 2.0) on the MySensors Gateway (Arduino UNO based) and I have tried to start/stop/restart OH2 after MySensors Gateway is up and running without success.

OH2 is capable to control for example Philips HUE lights without problems at the moment.

mortommy

Great news!

Regarding OH, I didn't have the opportunity to play with the v2.0 yet, I'm still on 1.8.1.
I have a serial mysensors gateway and this is my set up:

OH (v1.8.1) <-> OH MQTT binding (as MQTT client) <-> Mosquitto (as MQTT server) <-> mosquitto to serial (python script that reverts messages with topic mysensors to the serial port and vice-versa) <-> serial gateway.

So my items in OH are based on mqtt binding.

I guess OH2 and mysensors openhab binding make everything easier.

pentti12

Do you have interest to try OH2 together with MySensors Ethernet Gateway to get working?

I do not have enough force to push developers to make this happen. At the moment there is some problem on this, because full control is not possible. I think that MySensors Serial Gateway is working with OH2, but I don't like to use it. I like to connect my devices into LAN not cabling via old fashioned way using serial wires.

💬 MySensor Dioder (Ikea)

14

11.7k

11.2k

113.0k