About DS18B20 onewire.
Hardware
48
Posts
5
Posters
12.3k
Views
10
Watching
-
@pepson That's not necessary: The sketch reads the bus to get all the necessary info and will just send whatever is found.
If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.
Controller: FHEM; MySensors: 2.3.1, RS485,nRF24,RFM69, serial Gateways
-
@pepson That's not necessary: The sketch reads the bus to get all the necessary info and will just send whatever is found.
If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.
@rejoe2 said in About DS18B20 onewire.:
If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.
Ok i know how add to present description , but still dont know how add description to each sensors.... as in sketch for relay as i show as example.
-
@rejoe2 said in About DS18B20 onewire.:
If you want a "hardcoded version", you'd have to addopt the sketch for something in between these variants: if you use an array for the 1-wire addresses like https://github.com/rejoe2/MySensors-Dallas-Address-ChildID-Consistency/blob/master/Dallas_Addresses_Array_Solution/Dallas_Addresses_Array_Solution.ino does, just built the comment char-array based on that info.
Ok i know how add to present description , but still dont know how add description to each sensors.... as in sketch for relay as i show as example.
@pepson I'd suggest you make a test with the "simple" variant of the sketches. Then we could lateron discuss how to deal with an array containing the hardcoded addresses.
Pls. make also a test with the hardcoded version. Afai remember, it will print the needed array to serial, as long as #define PRINT_ARRAY isn't commented. -
@pepson yes. Just change the present call, just like in your sketch.
Example: change
present(i, S_HEATER);to
present(i, S_HEATER, "Description goes here");@mfalkvidd Can you help me... or change it ?
-
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller * http://www.mysensors.org/build/temp */ // Enable and select radio type attached #define MY_RADIO_NRF24 // Enable debug prints to serial monitor #define MY_DEBUG #define MY_NODE_ID 14 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected #define ATTACHED_DS18B20 40 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. byte D[ATTACHED_DS18B20][8] = { { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12 { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60 { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30 { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm) { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten }; float lastTemperature[ATTACHED_DS18B20]; // Initialize temperature message MyMessage msg(0,V_TEMP); MyMessage heat(0,V_STATUS); void setup() { // Startup up the OneWire library sensors.begin(); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("OneWire Temp+Heating LED", "20180709"); // Fetch the number of attached temperature sensors //numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i=0; i<ATTACHED_DS18B20; i++) { present(i, S_TEMP); } for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) { present(i, S_HEATER); } } void loop() { // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i=0; i<ATTACHED_DS18B20; i++) { //Serial.println(sensors.getResolution(D[i]), DEC); // Fetch and round temperature to one decimal // float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.; float temperature = sensors.getTempC(D[i]); // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature <= 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature,1)); // Save new temperatures for next compare lastTemperature[i]=temperature; } } for (int i=0; i<5;i++){ int value = analogRead(i); /*Serial.print("Pin"); Serial.print(i); Serial.print("="); Serial.println(value); */ int j=i+ATTACHED_DS18B20; if (value>150) { send(heat.setSensor(j).set(1)); } else { send(heat.setSensor(j).set(0)); } } sleep(SLEEP_TIME); }@flopp said in About DS18B20 onewire.:
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller * http://www.mysensors.org/build/temp */ // Enable and select radio type attached #define MY_RADIO_NRF24 // Enable debug prints to serial monitor #define MY_DEBUG #define MY_NODE_ID 14 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected #define ATTACHED_DS18B20 40 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. byte D[ATTACHED_DS18B20][8] = { { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12 { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60 { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30 { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm) { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten }; float lastTemperature[ATTACHED_DS18B20]; // Initialize temperature message MyMessage msg(0,V_TEMP); MyMessage heat(0,V_STATUS); void setup() { // Startup up the OneWire library sensors.begin(); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("OneWire Temp+Heating LED", "20180709"); // Fetch the number of attached temperature sensors //numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i=0; i<ATTACHED_DS18B20; i++) { present(i, S_TEMP); } for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) { present(i, S_HEATER); } } void loop() { // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i=0; i<ATTACHED_DS18B20; i++) { //Serial.println(sensors.getResolution(D[i]), DEC); // Fetch and round temperature to one decimal // float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.; float temperature = sensors.getTempC(D[i]); // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature <= 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature,1)); // Save new temperatures for next compare lastTemperature[i]=temperature; } } for (int i=0; i<5;i++){ int value = analogRead(i); /*Serial.print("Pin"); Serial.print(i); Serial.print("="); Serial.println(value); */ int j=i+ATTACHED_DS18B20; if (value>150) { send(heat.setSensor(j).set(1)); } else { send(heat.setSensor(j).set(0)); } } sleep(SLEEP_TIME); }When i try compile this sketch it get me error:
C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':
Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'
sensors.requestTemperatures();
^
exit status 1
expected initializer before 'sensors' -
@flopp said in About DS18B20 onewire.:
/** * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad <henrik.ekblad@mysensors.org> * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. * ******************************* * * DESCRIPTION * * Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller * http://www.mysensors.org/build/temp */ // Enable and select radio type attached #define MY_RADIO_NRF24 // Enable debug prints to serial monitor #define MY_DEBUG #define MY_NODE_ID 14 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected #define ATTACHED_DS18B20 40 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. byte D[ATTACHED_DS18B20][8] = { { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12 { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60 { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30 { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm) { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten }; float lastTemperature[ATTACHED_DS18B20]; // Initialize temperature message MyMessage msg(0,V_TEMP); MyMessage heat(0,V_STATUS); void setup() { // Startup up the OneWire library sensors.begin(); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("OneWire Temp+Heating LED", "20180709"); // Fetch the number of attached temperature sensors //numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i=0; i<ATTACHED_DS18B20; i++) { present(i, S_TEMP); } for (int i=ATTACHED_DS18B20; i<ATTACHED_DS18B20+5; i++) { present(i, S_HEATER); } } void loop() { // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i=0; i<ATTACHED_DS18B20; i++) { //Serial.println(sensors.getResolution(D[i]), DEC); // Fetch and round temperature to one decimal // float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.; float temperature = sensors.getTempC(D[i]); // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature <= 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature,1)); // Save new temperatures for next compare lastTemperature[i]=temperature; } } for (int i=0; i<5;i++){ int value = analogRead(i); /*Serial.print("Pin"); Serial.print(i); Serial.print("="); Serial.println(value); */ int j=i+ATTACHED_DS18B20; if (value>150) { send(heat.setSensor(j).set(1)); } else { send(heat.setSensor(j).set(0)); } } sleep(SLEEP_TIME); }When i try compile this sketch it get me error:
C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':
Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'
sensors.requestTemperatures();
^
exit status 1
expected initializer before 'sensors' -
@pepson you have a stray } after setWaitForConversion
Tip: use ctrl+t in the editor to easier see this type of mistake
@mfalkvidd
Still is problem after use CTRL+T/** The MySensors Arduino library handles the wireless radio link and protocol between your home built sensors/actuators and HA controller of choice. The sensors forms a self healing radio network with optional repeaters. Each repeater and gateway builds a routing tables in EEPROM which keeps track of the network topology allowing messages to be routed to nodes. Created by Henrik Ekblad <henrik.ekblad@mysensors.org> Copyright (C) 2013-2015 Sensnology AB Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors Documentation: http://www.mysensors.org Support Forum: http://forum.mysensors.org This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation. ******************************* DESCRIPTION Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller http://www.mysensors.org/build/temp */ #define MY_GATEWAY_SERIAL // Enable debug prints to serial monitor #define MY_DEBUG #define MY_NODE_ID 14 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected #define ATTACHED_DS18B20 40 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. byte D[ATTACHED_DS18B20][8] = { { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12 { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60 { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30 { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm) { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten }; float lastTemperature[ATTACHED_DS18B20]; // Initialize temperature message MyMessage msg(0, V_TEMP); MyMessage heat(0, V_STATUS); void setup() { // Startup up the OneWire library sensors.begin(); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("OneWire Temp+Heating LED", "20180709"); // Fetch the number of attached temperature sensors //numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i = 0; i < ATTACHED_DS18B20; i++) { present(i, S_TEMP); } for (int i = ATTACHED_DS18B20; i < ATTACHED_DS18B20 + 5; i++) { present(i, S_HEATER); } void loop() // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i = 0; i < ATTACHED_DS18B20; i++) { //Serial.println(sensors.getResolution(D[i]), DEC); // Fetch and round temperature to one decimal // float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.; float temperature = sensors.getTempC(D[i]); // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature <= 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature, 1)); // Save new temperatures for next compare lastTemperature[i] = temperature; } } for (int i = 0; i < 5; i++) { int value = analogRead(i); /*Serial.print("Pin"); Serial.print(i); Serial.print("="); Serial.println(value); */ int j = i + ATTACHED_DS18B20; if (value > 150) { send(heat.setSensor(j).set(1)); } else { send(heat.setSensor(j).set(0)); } } sleep(SLEEP_TIME); }C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':
Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'
sensors.requestTemperatures();
^
exit status 1
expected initializer before 'sensors' -
@mfalkvidd
Still is problem after use CTRL+T/** The MySensors Arduino library handles the wireless radio link and protocol between your home built sensors/actuators and HA controller of choice. The sensors forms a self healing radio network with optional repeaters. Each repeater and gateway builds a routing tables in EEPROM which keeps track of the network topology allowing messages to be routed to nodes. Created by Henrik Ekblad <henrik.ekblad@mysensors.org> Copyright (C) 2013-2015 Sensnology AB Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors Documentation: http://www.mysensors.org Support Forum: http://forum.mysensors.org This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License version 2 as published by the Free Software Foundation. ******************************* DESCRIPTION Example sketch showing how to send in DS1820B OneWire temperature readings back to the controller http://www.mysensors.org/build/temp */ #define MY_GATEWAY_SERIAL // Enable debug prints to serial monitor #define MY_DEBUG #define MY_NODE_ID 14 #include <SPI.h> #include <MySensors.h> #include <DallasTemperature.h> #define COMPARE_TEMP 0 // Send temperature only if changed? 1 = Yes 0 = No #define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected #define ATTACHED_DS18B20 40 unsigned long SLEEP_TIME = 60000; // Sleep time between reads (in milliseconds) OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs) DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. byte D[ATTACHED_DS18B20][8] = { { 0x10, 0x04, 0xB8, 0x3F, 0x02, 0x08, 0x00, 0xBD }, //KökTbx { 0x10, 0xF4, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0xB1 }, //UppTbx { 0x10, 0x92, 0x9F, 0x3E, 0x02, 0x08, 0x00, 0x98 }, //KökUt { 0x10, 0x4E, 0xE4, 0x3E, 0x02, 0x08, 0x00, 0x3C }, //ToaUt { 0x10, 0x1E, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x33 }, //EfterPump { 0x10, 0x09, 0xA1, 0x3E, 0x02, 0x08, 0x00, 0xF7 }, //HallTbx { 0x10, 0x59, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xFA }, //UppUt { 0x10, 0x07, 0x1B, 0x3F, 0x02, 0x08, 0x00, 0x99 }, //ToaTbx { 0x28, 0xFF, 0xB1, 0xAA, 0x63, 0x15, 0x03, 0xC8 }, //Kök { 0x10, 0x80, 0xB6, 0x3F, 0x02, 0x08, 0x00, 0x29 }, //Panna komp { 0x10, 0x3C, 0x9C, 0x3E, 0x02, 0x08, 0x00, 0x99 }, //Hall ut { 0x10, 0x42, 0xE0, 0x3F, 0x02, 0x08, 0x00, 0xD1 }, //Tvätt { 0x10, 0xCE, 0xE9, 0x3E, 0x02, 0x08, 0x00, 0x3A }, //T12 { 0x10, 0x99, 0xAC, 0x3F, 0x02, 0x08, 0x00, 0x25 }, //V mellan { 0x10, 0x15, 0xDB, 0x3E, 0x02, 0x08, 0x00, 0x01 }, //Hallen { 0x10, 0xF3, 0xD7, 0x3F, 0x02, 0x08, 0x00, 0x34 }, //Panna El { 0x10, 0xFB, 0xCB, 0x3F, 0x02, 0x08, 0x00, 0xC8 }, //Toa Nere { 0x10, 0x97, 0x23, 0x3F, 0x02, 0x08, 0x00, 0x92 }, //Varmvatten { 0x10, 0x0F, 0xE6, 0x3E, 0x02, 0x08, 0x00, 0xFD }, //Carport { 0x10, 0xF3, 0xC6, 0x3F, 0x02, 0x08, 0x00, 0x85 }, //Förrådet { 0x10, 0x9C, 0x3B, 0x52, 0x02, 0x08, 0x00, 0x25 }, //Mark 60 { 0x10, 0xF2, 0x24, 0x3F, 0x02, 0x08, 0x00, 0xEB }, //Vrum V { 0x10, 0x6A, 0x5E, 0x52, 0x02, 0x08, 0x00, 0x26 }, //Mark 30 { 0x10, 0x76, 0xCE, 0x3F, 0x02, 0x08, 0x00, 0xBA }, //Plattan { 0x10, 0x0E, 0x7B, 0x13, 0x02, 0x08, 0x00, 0x7C }, //Utetemp { 0x10, 0xEE, 0xEB, 0x3E, 0x02, 0x08, 0x00, 0x0F }, //Uterum { 0x28, 0x8C, 0x2D, 0xB4, 0x04, 0x00, 0x00, 0x9C }, //Kyl uppe { 0x28, 0xFF, 0xB2, 0x74, 0x63, 0x15, 0x02, 0xCC }, //Kyl mitten { 0x28, 0xFF, 0x08, 0x07, 0x52, 0x04, 0x00, 0xFF }, //Kyl nere { 0x28, 0xFF, 0xE6, 0x06, 0x52, 0x04, 0x00, 0x08 }, //Frys uppe { 0x28, 0xFF, 0xB4, 0x07, 0x55, 0x04, 0x00, 0xEB }, //Kyl bakom { 0x10, 0x1C, 0xA8, 0x3F, 0x02, 0x08, 0x00, 0x3B }, //Lucas { 0x10, 0x83, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x06 }, //Allrum { 0x10, 0xA3, 0xE8, 0x3E, 0x02, 0x08, 0x00, 0x7E }, //Theo { 0x10, 0x33, 0x3C, 0x3F, 0x02, 0x08, 0x00, 0x01 }, //Sovrum { 0x28, 0xFF, 0xFB, 0x3D, 0xC3, 0x16, 0x03, 0x58 }, //Panna luft in(varm) { 0x28, 0xFF, 0xD4, 0x1C, 0x00, 0x17, 0x03, 0x43 }, //Dränering { 0x28, 0xFF, 0x97, 0x11, 0x01, 0x15, 0x04, 0xC0 } // Poolvatten }; float lastTemperature[ATTACHED_DS18B20]; // Initialize temperature message MyMessage msg(0, V_TEMP); MyMessage heat(0, V_STATUS); void setup() { // Startup up the OneWire library sensors.begin(); // requestTemperatures() will not block current thread sensors.setWaitForConversion(false); } void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("OneWire Temp+Heating LED", "20180709"); // Fetch the number of attached temperature sensors //numSensors = sensors.getDeviceCount(); // Present all sensors to controller for (int i = 0; i < ATTACHED_DS18B20; i++) { present(i, S_TEMP); } for (int i = ATTACHED_DS18B20; i < ATTACHED_DS18B20 + 5; i++) { present(i, S_HEATER); } void loop() // Fetch temperatures from Dallas sensors sensors.requestTemperatures(); // query conversion time and sleep until conversion completed int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution()); // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater) sleep(conversionTime); // Read temperatures and send them to controller for (int i = 0; i < ATTACHED_DS18B20; i++) { //Serial.println(sensors.getResolution(D[i]), DEC); // Fetch and round temperature to one decimal // float temperature = static_cast<float>(static_cast<int>((sensors.requestTemperaturesByAddress(D[i])) * 10.)) / 10.; float temperature = sensors.getTempC(D[i]); // Only send data if temperature has changed and no error #if COMPARE_TEMP == 1 if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) { #else if (temperature != -127.00 && temperature <= 85.00) { #endif // Send in the new temperature send(msg.setSensor(i).set(temperature, 1)); // Save new temperatures for next compare lastTemperature[i] = temperature; } } for (int i = 0; i < 5; i++) { int value = analogRead(i); /*Serial.print("Pin"); Serial.print(i); Serial.print("="); Serial.println(value); */ int j = i + ATTACHED_DS18B20; if (value > 150) { send(heat.setSensor(j).set(1)); } else { send(heat.setSensor(j).set(0)); } } sleep(SLEEP_TIME); }C:\Users\Piotrek\Desktop\Temp dallas\Arduino_dallas_18B20_with_desc\Arduino_dallas_18B20_with_desc.ino: In function 'void presentation()':
Arduino_dallas_18B20_with_desc:117:3: error: expected initializer before 'sensors'
sensors.requestTemperatures();
^
exit status 1
expected initializer before 'sensors' -
@mfalkvidd
Where ? please show me more.... :( i am beginner -
But.... Can you also help me to add to this sketch option to send to example to Home Assistant also DESCRIPTION to each sensors ? And description will be get from sketch from name about address sensor ?
As in this sketch which i have for relay:
#define USE_EXPANDER // Enable debug prints to serial monitor //#define MY_DEBUG #define MY_GATEWAY_SERIAL #include <MySensors.h> #include <Bounce2.h> #ifdef USE_EXPANDER #include <Wire.h> // Required for I2C communication #include "PCF8574.h" uint8_t expanderAddresses[] = {0x20}; const int numberOfExpanders = sizeof(expanderAddresses); PCF8574 expander[numberOfExpanders]; #define E(expanderNo, ExpanderPin) (((expanderNo+1)<<8) | (ExpanderPin)) #endif // No Button Constant #define NOB -1 #define MULTI_RELAY_VERSION 9 #define RELAY_STATE_STORAGE 1 const uint8_t RELAY_TRIGGER_LOW = 0; const uint8_t RELAY_TRIGGER_HIGH = 1; const uint8_t RELAY_STARTUP_ON = 2; const uint8_t RELAY_STARTUP_OFF = 4; const uint8_t RELAY_STARTUP_MASK = RELAY_STARTUP_ON | RELAY_STARTUP_OFF; enum ButtonType { MONO_STABLE = 0, BI_STABLE = 1, DING_DONG = 2 // HIGH state immediatly after push, LOW state after release }; typedef struct { int sensorId; int relay; int button; uint8_t relayOptions; ButtonType buttonType; const char * relayDescription; } RelayButton; // CONFIGURE ONLY THIS ARRAY! // Row params: sensor ID - sensor ID reported on MySensor Gateway // relay pin - Expander supported // button pin - <0 for virtual buttons (only available in MySensor Gateway); no support for Expander // relay options - [RELAY_TRIGGER_LOW|RELAY_TRIGGER_HIGH] {RELAY_STARTUP_ON|RELAY_STARTUP_OFF} // button type - [MONO_STABLE|BI_STABLE|DING_DONG] // relay description - reported on MySensor Gateway, can help identify device on initial configuration in Home Automation App, can be empty ("") RelayButton myRelayButtons[] = { {0, 2, A0, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł2 - kinkiet [C10]"}, // WŁ: Ł2 {1, 16, A1, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 2 [A9]"}, // WŁ: Salon 2 {2, 15, A2, RELAY_TRIGGER_LOW, BI_STABLE, "Salon 1 [A10]"}, // WŁ: Salon 1 {3, E(0,1), A3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, BI_STABLE, "Halogen - Taras [B8]"}, // WŁ: Taras {4, 22, A4, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia [B2]"}, // WŁ: Kuchnia 1 {5, 23, A5, RELAY_TRIGGER_LOW, BI_STABLE, "Kuchnia - Kinkiet [B3]"}, // WŁ: Kuchnia 2 {6, 28, A6, RELAY_TRIGGER_LOW, BI_STABLE, "Jadalnia 2 [A4]"}, // WŁ: Hall I/Jadalnia prawy {17, 17, A7, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Kinkiet [A11]"}, // WŁ: Hall I/Ł1 prawy {8, 31, A8, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"}, // WŁ: Kotłownia/Garaż {8, 31, A9, RELAY_TRIGGER_LOW, MONO_STABLE, "Garaż [A7]"}, // WŁ: Garaż {10, 14, A10, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, BI_STABLE, "Halogen - wejście [B4]"}, // WŁ: Drzwi wejściowe {11, E(0,7), A11, RELAY_TRIGGER_LOW, DING_DONG, "Dzwonek [?]"}, // WŁ: Dzwonek {12, 29, A12, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"}, // WŁ: Hall I/Jadalnia lewy {12, 29, A13, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"}, // WŁ: Hall I/Wiatrołap {14, 32, A14, RELAY_TRIGGER_LOW, BI_STABLE, "Wiatrołap [A8]"}, // WŁ: Wiatrołap/Hall I {15, 19, A15, RELAY_TRIGGER_LOW, MONO_STABLE, "Kotłownia [B1]"}, // WŁ: Kotłownia/Hall I {16, 24, 53, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 - Taśma LED [C1]"}, // WŁ: Hall I/Ł1 środek {17, 17, 52, RELAY_TRIGGER_LOW, MONO_STABLE, "Ł1 - Kinkiet [A11]"}, // WŁ: Ł1 {18, 18, 51, RELAY_TRIGGER_LOW, BI_STABLE, "Ł1 [A12]"}, // WŁ: Hall I/Ł1 lewy {19, 6, 50, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"}, // WŁ: Hall I/Schody 1 {12, 29, 49, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 1 [A5]"}, // WŁ: Hall I/Schody 2 {21, 26, 48, RELAY_TRIGGER_LOW, BI_STABLE, "Gabinet [A2]"}, // WŁ: Gabinet {22, 7, 47, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"}, // WŁ: Hall II/Schody 1 {19, 6, 46, RELAY_TRIGGER_LOW, BI_STABLE, "Klatka Schodowa [B7]"}, // WŁ: Hall II/Schody 2 {24, 10, 45, RELAY_TRIGGER_LOW, BI_STABLE, "Garderoba [C12]"}, // WŁ: Garderoba {25, 4, 44, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad kuchnią 2 [B10]"}, // WŁ: Pok. nad kuchnią 2 {26, 5, 43, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad kuchnią 1 [B9]"}, // WŁ: Pok. nad kuchnią 1 {27, 8, 42, RELAY_TRIGGER_LOW, BI_STABLE, "Pok. nad salonem 2 [B12]"}, // WŁ: Pok. nad salonem 2 {28, 9, 41, RELAY_TRIGGER_LOW, MONO_STABLE, "Pok. nad salonem 1 [B11]"}, // WŁ: Pok. nad salonem 1 {29, 3, 40, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 [C7]"}, // WŁ: Hall II/Ł2 1 {30, E(0,3), 39, RELAY_TRIGGER_LOW, BI_STABLE, "Ł2 - Taśma LED [?]"}, // WŁ: Hall II/Ł2 2 {22, 7, 38, RELAY_TRIGGER_LOW, BI_STABLE, "Hall 2 [B5]"}, // WŁ: Hall II/Sypialnia {32, 11, 37, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 2 [C9]"}, // WŁ: Sypialnia 2 {33, 12, 36, RELAY_TRIGGER_LOW, BI_STABLE, "Sypialnia 1 [C8]"}, // WŁ: Sypialnia 1 {34, 25, -1, RELAY_TRIGGER_LOW | RELAY_STARTUP_ON, MONO_STABLE, "Halogen - Garaż [A1]"}, // WŁ: Virtual Button 1 {35, 30, -2, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł1 - Wentylator [A3]"}, // WŁ: Virtual Button 2 {36, E(0,2), -3, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Halogen - wschód [B6]"}, // WŁ: Virtual Button 3 {37, E(0,4), -4, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki schodowe [C6]"}, // WŁ: Virtual Button 4 {38, E(0,5), -5, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe I [C4]"}, // WŁ: Virtual Button 5 {39, E(0,6), -6, RELAY_TRIGGER_LOW, MONO_STABLE, "Lampki podłogowe II [C2]"}, // WŁ: Virtual Button 6 {40, E(0,0), -7, RELAY_TRIGGER_LOW | RELAY_STARTUP_OFF, MONO_STABLE, "Ł2 - wentylator [C11]"}, // WŁ: Virtual Button 7 }; const int numberOfRelayButtons = sizeof(myRelayButtons) / sizeof(RelayButton); typedef struct { int firstButton; int nextButton; } RelayMultiButtons; RelayMultiButtons relayMultiButtons[numberOfRelayButtons]; uint8_t myRelayState[numberOfRelayButtons]; // MySensors - Sending Data // To send data you have to create a MyMessage container to hold the information. MyMessage msgs[numberOfRelayButtons]; Bounce myButtonDebouncer[numberOfRelayButtons]; //Function Declaration uint8_t loadRelayState(int relayNum, uint8_t forceEeprom = 0); void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom); void saveRelayState(int relayNum, uint8_t state); void changeRelayState(int relayNum, uint8_t relayState); // MySensors - This will execute before MySensors starts up void before() { Serial.begin(115200); #ifdef USE_EXPANDER /* Start I2C bus and PCF8574 instance */ for(int i = 0; i < numberOfExpanders; i++) { expander[i].begin(expanderAddresses[i]); } #endif // initialize multiple buttons list structure for (int i = 0; i < numberOfRelayButtons; i++) { relayMultiButtons[i].firstButton = -1; relayMultiButtons[i].nextButton = -1; } // find multiple buttons for the same relay (uni-directional list) for (int i = 0; i < numberOfRelayButtons-1; i++) { if (relayMultiButtons[i].firstButton == -1) { int prevRelayButton = i; for (int j = i+1; j < numberOfRelayButtons; j++) { if (myRelayButtons[i].relay == myRelayButtons[j].relay) { relayMultiButtons[prevRelayButton].firstButton = i; relayMultiButtons[prevRelayButton].nextButton = j; relayMultiButtons[j].firstButton = i; prevRelayButton = j; } } } } // if version has changed, reset state of all relays int versionChangeResetState = (MULTI_RELAY_VERSION == loadState(0) ) ? 0 : 1; for (int i = 0; i < numberOfRelayButtons; i++) { // if this relay has multiple buttons, load only first if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) { // Then set relay pins in output mode #ifdef USE_EXPANDER if ( myRelayButtons[i].relay & 0xff00 ) { // EXPANDER int expanderNo = (myRelayButtons[i].relay >> 8) - 1; int expanderPin = myRelayButtons[i].relay & 0xff; expander[expanderNo].pinMode(expanderPin, OUTPUT); } else { #endif pinMode(myRelayButtons[i].relay, OUTPUT); #ifdef USE_EXPANDER } #endif uint8_t isTurnedOn = 0; if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) { isTurnedOn = 1; } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) { } else { // Set relay to last known state (using eeprom storage) isTurnedOn = loadRelayState(i, 1); // 1 - true, 0 - false if (versionChangeResetState && isTurnedOn) { saveRelayState(i, 0, 1); isTurnedOn = 0; } } changeRelayState(i, isTurnedOn); myRelayState[i] = isTurnedOn; } } if (versionChangeResetState) { // version has changed, so store new version in eeporom saveState(0, MULTI_RELAY_VERSION); } } // executed AFTER mysensors has been initialised void setup() { for(int i = 0; i < numberOfRelayButtons; i++) { if (myRelayButtons[i].button >= 0) { // No Expander support for buttons (de-bouncing) pinMode(myRelayButtons[i].button, INPUT_PULLUP); // HIGH state when button is not pushed } } // Setup locally attached sensors delay(5000); // Send state to MySensor Gateway for(int i = 0; i < numberOfRelayButtons; i++) { // if this relay has multiple buttons, send only first if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) { msgs[i] = MyMessage(myRelayButtons[i].sensorId, V_LIGHT); uint8_t relayState; if (myRelayButtons[i].relayOptions & RELAY_STARTUP_ON) { relayState = 1; } else if (myRelayButtons[i].relayOptions & RELAY_STARTUP_OFF) { relayState = 0; } else { relayState = loadRelayState(i); } send(msgs[i].set(relayState)); // send current state } } // Setup buttons for(int i = 0; i < numberOfRelayButtons; i++) { if (myRelayButtons[i].button >= 0) { // setup debouncer myButtonDebouncer[i] = Bounce(); myButtonDebouncer[i].attach(myRelayButtons[i].button); myButtonDebouncer[i].interval(50); } } } void loop() { for(int i = 0; i < numberOfRelayButtons; i++) { if (myRelayButtons[i].button >= 0 && myButtonDebouncer[i].update()) { int buttonState = myButtonDebouncer[i].read(); #ifdef MY_DEBUG Serial.print("# Button "); Serial.print(i); Serial.print(" changed to: "); Serial.println(buttonState); #endif int relayNum = (relayMultiButtons[i].firstButton == -1) ? i : relayMultiButtons[i].firstButton; if (myRelayButtons[i].buttonType == DING_DONG) { if (buttonState == LOW) { // button pressed changeRelayState(relayNum, 1); send(msgs[relayNum].set(1)); } else { // button released changeRelayState(relayNum, 0); send(msgs[relayNum].set(0)); } } else if (myRelayButtons[i].buttonType == BI_STABLE || buttonState == HIGH) { // If button type is BI_STABLE, any change will toggle relay state // For MONO_STABLE, button must be pushed and released (HIGH) uint8_t isTurnedOn = ! loadRelayState(relayNum); // 1 - true, 0 - false changeRelayState(relayNum, isTurnedOn); send(msgs[relayNum].set(isTurnedOn)); saveRelayState(relayNum, isTurnedOn); } } } } // MySensors - Presentation // Your sensor must first present itself to the controller. // The presentation is a hint to allow controller prepare for the sensor data that eventually will come. // Executed after "before()" and before "setup()" in: _begin (MySensorsCore.cpp) > gatewayTransportInit() > presentNode() void presentation() { // Send the sketch version information to the gateway and Controller sendSketchInfo("Multi Relay", "1.2"); // Register every relay as separate sensor for (int i = 0; i < numberOfRelayButtons; i++) { // if this relay has multiple buttons, register only first if (relayMultiButtons[i].firstButton == -1 || relayMultiButtons[i].firstButton == i) { // Register all sensors to gw (they will be created as child devices) // void present(uint8_t childSensorId, uint8_t sensorType, const char *description, bool ack); // childSensorId - The unique child id you want to choose for the sensor connected to this Arduino. Range 0-254. // sensorType - The sensor type you want to create. // description An optional textual description of the attached sensor. // ack - Set this to true if you want destination node to send ack back to this node. Default is not to request any ack. present(myRelayButtons[i].sensorId, S_BINARY, myRelayButtons[i].relayDescription); } } } // MySensors - Handling incoming messages // Nodes that expects incoming data, such as an actuator or repeating nodes, // must implement the receive() - function to handle the incoming messages. // Do not sleep a node where you expect incoming data or you will lose messages. void receive(const MyMessage &message) { // We only expect one type of message from controller. But we better check anyway. if (message.type == V_STATUS) { uint8_t isTurnedOn = message.getBool(); // 1 - true, 0 - false changeRelayState(message.sensor, isTurnedOn); // Store state in eeprom if changed if (loadRelayState(message.sensor) != isTurnedOn) { saveRelayState(message.sensor, isTurnedOn); } send(msgs[message.sensor].set(isTurnedOn)); // support for OPTIMISTIC=FALSE (Home Asistant) #ifdef MY_DEBUG // Write some debug info Serial.print("# Incoming change for sensor: " + message.sensor); Serial.println(", New status: " + isTurnedOn); #endif } } uint8_t loadRelayState(int relayNum, uint8_t forceEeprom) { uint8_t relayState; if (forceEeprom) { relayState = loadState(RELAY_STATE_STORAGE + relayNum); } else { relayState = myRelayState[relayNum]; } #ifdef MY_DEBUG Serial.print("# loadRelayState: "); Serial.print(relayNum); if (forceEeprom) { Serial.print("(byte "); Serial.print(RELAY_STATE_STORAGE + relayNum); Serial.print(")"); } Serial.print(" = "); Serial.println(relayState); #endif return(relayState); } void saveRelayState(int relayNum, uint8_t state, uint8_t useEeprom) { int mainRelayNum = (relayMultiButtons[relayNum].firstButton == -1) ? relayNum : relayMultiButtons[relayNum].firstButton; myRelayState[mainRelayNum] = state; if (useEeprom && (relayNum == mainRelayNum)) { saveState(RELAY_STATE_STORAGE + mainRelayNum, state); } int nextButton = mainRelayNum; // update all buttons while ((nextButton = relayMultiButtons[nextButton].nextButton) != -1) { myRelayState[nextButton] = state; }; } void saveRelayState(int relayNum, uint8_t state) { uint8_t useEeprom = ((myRelayButtons[relayNum].relayOptions & RELAY_STARTUP_MASK) == 0); saveRelayState(relayNum, state, useEeprom); } void changeRelayState(int relayNum, uint8_t relayState) { uint8_t relayTrigger = myRelayButtons[relayNum].relayOptions & RELAY_TRIGGER_HIGH; uint8_t digitalOutState = relayState ? relayTrigger : ! relayTrigger; #ifdef USE_EXPANDER if ( myRelayButtons[relayNum].relay & 0xff00 ) { int expanderNo = (myRelayButtons[relayNum].relay >> 8) - 1; int expanderPin = myRelayButtons[relayNum].relay & 0xff; expander[expanderNo].digitalWrite(expanderPin, digitalOutState); } else { #endif digitalWrite(myRelayButtons[relayNum].relay, digitalOutState); #ifdef USE_EXPANDER } #endif }And in Home assistant show example decription: Ł2 - kinkiet [C10] or for second Salon 2 [A9] etc.
Please help me... because it will be good to identify sensors when add to Controller.
